Page 1 Grand Cherokee Grand Cherokee Grand Cherokee 2 0 1 4 2 0 1 4 2 0 1 4 O W N E R ’ S M A N U A L O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of fea- Chrysler Group LLC shall be deemed to be deleted and the tures and equipment that are either standard or optional on name Chrysler Canada Inc.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....8 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, Congratulations on selecting your new Chrysler Group particularly those used for braking, steering, transmis- LLC vehicle. Be assured that it represents precision sion, and transfer case shifting.
Page 7: Rollover Warning
INTRODUCTION 5 This Owner’s Manual has been prepared with the assis- ROLLOVER WARNING tance of service and engineering specialists to acquaint Utility vehicles have a significantly higher rollover rate you with the operation and maintenance of your vehicle. than other types of vehicles. This vehicle has a higher It is supplemented by Warranty Information, and various ground clearance and a higher center of gravity than customer-oriented documents.
Page 8: How To Use This Manual
6 INTRODUCTION two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
Page 9 INTRODUCTION 7...
Page 10: Warnings And Cautions
8 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against oper- ating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information.
Page 11: Vehicle Modifications/Alterations
INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 13: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ... . .14 To Arm The System .....21 Keyless Ignition Node (KIN) .
Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information ....28 OCCUPANT RESTRAINTS ....49 REMOTE STARTING SYSTEM —...
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Seat Belt Lock Out..... .67 ENGINE BREAK-IN RECOMMENDATIONS . . .108 Seat Belts And Pregnant Women ...67 SAFETY TIPS .
Page 16: A Word About Your Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate Your vehicle uses a keyless ignition system. This system when in position. The three positions are OFF, ACC, and consists of a Key Fob with Remote Keyless Entry (RKE) ON/RUN.
Page 17: Key Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The emergency key is also for locking the glove box. You can keep the emergency key with you when valet parking. To remove the emergency key, slide the mechanical latch on the back of the Key Fob sideways with your thumb and then pull the key out with your other hand.
Page 18: Ignition Or Accessory On Message
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
Page 19 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! WARNING! (Continued) • Do not leave children or animals inside parked • When leaving the vehicle, always remove the Key vehicles in hot weather. Interior heat build-up may Fob from the vehicle and lock your vehicle. cause serious injury or death.
Page 20: Sentry Key
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY® it indicates that someone used an invalid Key Fob to start the engine. Either of these conditions will result in the The Sentry Key® Immobilizer system prevents unauthor- engine being shut off after two seconds. ized vehicle operation by disabling the engine.
Page 21: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Replacement Keys At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). NOTE: Only Key Fobs that are programmed to the Keep the PIN in a secure location. This number is vehicle electronics can be used to start and operate the required for authorized dealer replacement of Key Fobs.
Page 22: General Information
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information and/or turn signals will flash repeatedly for three min- utes. If the disturbance is still present (driver’s door, The Sentry Key® system complies with FCC rules Part 15 passenger door, other doors, ignition) after three minutes, and with RSS-210 of Industry Canada.
Page 23: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To Arm The System exterior zone (refer to Keyless Enter-N-Go™ in Things To Know Before Starting Your Vehicle for further infor- Follow these steps to arm the Vehicle Security Alarm: mation). 1. Remove the key from the ignition system (refer to •...
Page 24: Tamper Alert
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle • The driver’s door key cylinder and the liftgate button and open a door, the alarm will sound.
Page 25: Illuminated Entry - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 ILLUMINATED ENTRY — IF EQUIPPED NOTE: • The front courtesy overhead console and door cour- The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the tesy lights will turn on if the dimmer control is in the doors or open any door.
Page 26: To Unlock The Doors And Liftgate
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Driving at speeds 5 mph (8 km/h) and above To Unlock The Doors And Liftgate disables the system from responding to all RKE transmit- Press and release the UNLOCK button on the RKE ter buttons for all RKE transmitters.
Page 27: To Lock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Flash Lights With Remote Key To Lock The Doors And Liftgate This feature will cause the turn signal lights to flash when Press and release the LOCK button on the RKE transmit- the doors are locked or unlocked with the RKE transmit- ter to lock all doors and liftgate.
Page 28: Using The Panic Alarm
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • You may need to be less than 35 ft (11 m) from the Using The Panic Alarm vehicle when using the RKE transmitter to turn off the To turn the Panic Alarm feature on or off, press and hold Panic Alarm due to the radio frequency noises emitted the PANIC button on the RKE transmitter for at least by the system.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 1. Remove the emergency key by sliding the mechanical latch on the back of the RKE transmitter sideways with your thumb and then pull the key out with your other hand. 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart.
Page 30: Things To Know Before Starting Your Vehicle General Information
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE new battery with your fingers. Skin oils may cause If your RKE transmitter fails to operate from a normal battery deterioration. If you touch a battery, clean it distance, check for these two conditions: with rubbing alcohol.
Page 31: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • RKE PANIC button not pressed NOTE: • The vehicle must be equipped with an automatic • Fuel meets minimum requirement transmission to be equipped with Remote Start. • System not disabled from previous remote start event •...
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle To Enter Remote Start Mode Information Center (EVIC) — If Equipped The following messages will display in the EVIC if the Press and release the REMOTE START button vehicle fails to remote start or exits remote start prema- on the RKE transmitter twice within five sec- turely:...
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of the 15-minute cycle, press and release in the Remote Start mode.
Page 34: Door Locks
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Comfort Systems — If Equipped DOOR LOCKS When remote start is activated, the heated steering The power door locks can be manually locked from wheel, and driver heated seat features will automatically inside the vehicle by using the door lock knob.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! (Continued) • When leaving the vehicle, always remove the Key Fob from the vehicle and lock your vehicle. Unsu- pervised use of vehicle equipment may cause severe personal injuries or death. •...
Page 36: Power Door Locks
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks If you press the door lock switch while the Key Fob is in the vehicle and the driver’s door is open, the doors will The power door lock switch is located on each front door not lock.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 3. Repeat steps 1 and 2 for the opposite rear door. Child-Protection Door Lock Function Child-Protection Door Lock Location WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged (locked).
Page 38: Keyless Enter-N-Go
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the vehicle is unlocked by Passive Entry and no door NOTE: For emergency exit from the rear seats when the Child-Protection Door Lock System is engaged, manually goes ajar within 60 seconds, the vehicle will re-lock raise the door lock knob to the unlocked position, roll and if equipped will arm the theft alarm.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Unlock From The Passenger Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automati- cally.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If one of the vehicle doors is open and the door panel NOTE: If the vehicle is unlocked then the liftgate will open switch is used to lock the vehicle, once all open doors with the handle and no RKE Transmitter is required.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Lock The Liftgate To Lock The Vehicle’s Doors With a valid Passive Entry RKE transmitter within 3 ft With one of the vehicle’s Passive Entry RKE transmitters (1.0 m) of the liftgate, press the passive entry lock button within 5 ft (1.5 m) of the driver or passenger front door located to the right of electronic liftgate handle.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do NOT grab the door handle, when pressing the door NOTE: handle lock button. This could unlock the door(s). • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle.
Page 43: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door and rear doors which operate the front passenger and rear passenger door windows.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press to the first detent WARNING! and release it when you want the window to stop. Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, and do not leave a vehicle equipped with Keyless Enter-N-Go™...
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 To stop the window from going all the way up during the NOTE: If the window runs into any obstacle during Auto Up operation, push down on the switch briefly. Auto Up it will reverse direction and then go back down. Remove the obstacle and use the window switch again to To close the window part way, lift the window switch to close the window.
Page 46: Wind Buffeting
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Resetting The Auto Up Feature Should the Auto Up feature stop working, the window probably needs to be reset. To reset Auto Up: 1. Pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 47: Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 open or partially open positions. This is a normal occur- NOTE: The liftgate passive entry lock button will only rence and can be minimized. If the buffeting occurs with lock the liftgate, the liftgate unlock feature is built into the rear windows open, then open the front and rear the electronic liftgate handle.
Page 48: Power Liftgate - If Equipped
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Liftgate — If Equipped The power liftgate may be opened by pressing the electronic liftgate handle (refer to Keyless Enter-N-Go located in Things To Know Before Starting) or by pressing the LIFTGATE button on the Remote Keyless Entry (RKE) transmitter.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 When the LIFTGATE button on the RKE transmitter is WARNING! pressed two times, the turn signals will flash twice to signal that the liftgate is opening or closing (if Flash During power operation, personal injury or cargo Lamps with Lock is enabled in the EVIC) and the liftgate damage may occur.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If anything obstructs the power liftgate while it is • If the power liftgate encounters multiple obstructions closing or opening, the liftgate will automatically within the same cycle, the system will automatically reverse to the closed or open position, provided it stop and the liftgate must be opened or closed manually.
Page 51: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • An energy-absorbing steering column and steering OCCUPANT RESTRAINTS wheel Some of the most important safety features in your • Knee bolsters for front seat occupants vehicle are the restraint systems: • Three-point lap and shoulder belts for the driver and •...
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you will be carrying children too small for adult-sized WARNING! seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold Infants in rear facing child restraints should never infant and child restraint systems.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 If a child from 1 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact as far back as possible and use the proper child restraint.
Page 54: Lap/Shoulder Belts
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Supplemental Side Air Bag Inflatable Curtain and cause a collision that includes you. This can happen (SABIC) and Seat-Mounted Side Air Bags (SAB) far away from home or on your own street.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 This feature allows the shoulder part of the belt to move WARNING! (Continued) freely with you under normal conditions. However, in an • Two people should never be belted into a single collision the belt will lock and reduce the risk of you seat belt.
Page 56: Lap/Shoulder Belt Operating Instructions
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! • A shoulder belt placed behind you will not protect • A lap belt worn too high can increase the risk of you from injury during a collision. You are more injury in a collision.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
Page 60: Lap/Shoulder Belt Untwisting Procedure
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Adjustable Upper Shoulder Belt Anchorage Use the following procedure to untwist a twisted lap/ In the front seating positions, the shoulder belt can be shoulder belt. adjusted upward or downward to position the belt away from your neck.
Page 61: Seat Belts In Passenger Seating Positions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 As a guide, if you are shorter than average, you will additional information, refer to “Installing Child Re- prefer a lower position, and if you are taller than average, straints Using The Vehicle Seat Belt” under the “Child you will prefer a higher position.
Page 62: Automatic Locking Retractor Mode (Alr) - If Equipped
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to retract completely in this case and then carefully pull How To Engage The Automatic Locking Mode out only the amount of webbing necessary to comfort- 1. Buckle the combination lap and shoulder belt. ably wrap around the occupant’s mid-section.
Page 63: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Seat Belt Pretensioners WARNING! The seat belts for both front seating positions are • The belt and retractor assembly must be replaced if equipped with pretensioning devices that are designed to the seat belt assembly Automatic Locking Retractor remove slack from the seat belt in the event of a collision.
Page 64: Supplemental Active Head Restraints (Ahr)
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Active Head Restraints (AHR) When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap These head restraints are passive, deployable compo- between the back of the occupant’s head and the AHR.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 66: Things To Know Before Starting Your Vehicle 11
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the Active into the back decorative plastic half.
Page 68: Enhanced Seat Belt Use Reminder System (Beltalert®)
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System unbuckled while traveling at speeds greater than 5 mph (BeltAlert®) (8 km/h), BeltAlert® will provide both audio and visual notification. BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger The front passenger seat BeltAlert®...
Page 69: Seat Belt Lock Out
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Seat Belt Lock Out Seat Belt Extender The center rear seat belt system has a lock out feature that If a seat belt is too short even when fully extended and will not allow you to extract the center webbing unless when the adjustable upper shoulder belt anchorage (if the rear seat upper latch is engaged.
Page 70: Supplemental Restraint System (Srs) - Air Bags
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 The Advanced Front Air Bags have a multistage inflator This vehicle is equipped with Supplemental Seat-Mounted design. This allows the air bag to have different rates of Side Air Bags (SAB) to provide enhanced protection for an inflation based on several factors, including the severity occupant during a side impact.
Page 72: Advanced Front Air Bag Features
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front and Side Impact Sensors Air Bag System Components • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, Your vehicle may be equipped with the following air bag system components: and Seat Track Position Sensors •...
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Supplemental Seat-Mounted Side Air Bags (SAB) WARNING! Supplemental Seat-Mounted Side Air Bags (SAB) may • No objects should be placed over or near the air bag provide enhanced protection to help protect an occupant on the instrument panel, because any such objects during a side impact.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 NOTE: WARNING! • Air Bag covers may not be obvious in the interior trim, • Your vehicle is equipped with left and right but they will open during air bag deployment. SABIC, do not stack luggage or other cargo up high •...
Page 76: Air Bag Deployment Sensors And Controls
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Always sit upright as possible with your back against the Along with seat belts and pretensioners, Advanced Front seat back, use the seat belts properly, and use the Air Bags work with the knee bolsters to provide im- appropriate sized child restraint, infant restraint or proved protection for the driver and front passenger.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 ORC deploys the Advanced Front Air Bags, Supplemen- depending on the type and location of impact, Advanced tal Driver Side Knee Air Bag, SABIC air bags, SAB air Front Air Bags and Supplemental Driver Side Knee Air bags, and front seat belt pretensioners, as required, Bag may deploy in crashes with little vehicle front-end depending on several factors, including the severity and...
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE position, in the ACC position, or not in the ignition, the WARNING! air bag system is not on and the air bags will not inflate. Ignoring the Air Bag Warning Light in your instru- The ORC contains a backup power supply system that ment panel could mean you won’t have the air bags may deploy the air bags even if the battery loses power or...
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 are possible, based on several factors, including the Based on the severity and type of collision, the side air collision type and severity. The steering wheel hub trim bag inflator on the crash side of the vehicle may be cover and the upper right side of the instrument panel triggered, releasing a quantity of non-toxic gas.
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE folds out of the way allowing the air bag to inflate to the where the SABIC inflates. This especially applies to full size. The air bag fully inflates in about 15 to 20 mil- children.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 event the ORC will determine whether to have the If A Deployment Occurs Enhanced Accident Response System perform the follow- The Advanced Front Air Bags are designed to deflate ing functions: immediately after deployment. •...
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a Do not drive your vehicle after the air bags have de- few days, or if you have any blistering, see your doctor ployed. If you are involved in another collision, the air immediately.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 84: Event Data Recorder (Edr)
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may You will want to have the air bags ready to not be ready to inflate for your protection.
Page 85: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 time, typically 30 seconds or less. The EDR in this vehicle are recorded. However, other parties, such as law en- is designed to record such data as: forcement, could combine the EDR data with the type of personally identifying data routinely acquired during a •...
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years or younger should ride properly NOTE: For additional information, refer buckled up in a rear seat, if available. According to crash to www.seatcheck.org or call 1–866–SEATCHECK. statistics, children are safer when properly restrained in Canadian residents should refer to Transport the rear seats rather than in the front.
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight or Age Recommended Type of Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convertible younger and who have not reached Child Restraint, facing rearward in the the height or weight limits of their...
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearward- reach the highest weight or height allowed by their facing in the vehicle until they are two years old or until convertible child seat.
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Older Children And Child Restraints seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt. Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- WARNING! facing in the vehicle.
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 4.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – LATCH – Child + Child Lower Anchors Seat Belt + Top Lower Anchors Seat Belt Only Restraint...
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchor / Top Tether Locations Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol...
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint LATCH Positions What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Can two child restraints be attached using Never “share” a LATCH anchorage with a common lower LATCH anchorage? two or more child restraints. If the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH...
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages Locating The LATCH Anchorages The lower anchorages are round bars that are The lower anchorages are round bars that are found at the rear of the seat cushion where it found at the rear of the seat cushion where it meets the seatback.
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Pulling Down The Carpet Floor Panel To Access Top Pulling Down The Carpet Floor Panel To Access Top Tether Strap Tether Strap...
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems will be WARNING! equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower Never use the same lower anchorage to attach more anchorage and a way to tighten the connection to the than one child restraint.
Page 99 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 1. To access the center seat arm rest tether, first lower the 3. Raise the armrest and attach the tether hook to the arm rest. The tether is located behind the armrest and strap located on the front of the arm rest.
Page 100 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Install A LATCH-compatible Child Restraint 4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- 1. If the selected seating position has a Switchable Auto- ing position.
Page 101 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 How To Stow An Unused ALR Seatbelt WARNING! When using the LATCH attaching system to install a Improper installation of a child restraint to the child restraint, stow all ALR seat belts that are not being LATCH anchorages can lead to failure of the re- used by other occupants or being used to secure child straint.
Page 102 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE be “switched” into a locked mode by pulling all of the Lap/Shoulder Belt Systems for Installing Child webbing out of the retractor and then letting the webbing Restraints in this Vehicle retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back into the retractor.
Page 103 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 What is the weight limit (child’s weight Weight limit of the Always use the tether anchor when using + weight of the child restraint) for using Child Restraint the seat belt to install a forward facing the Tether Anchor with the seat belt to child restraint, up to the recommended attach a forward facing child restraint?
Page 104 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint with a Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 105 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 8. If the child restraint has a top tether strap and the Installing A Child Restraint With A Cinching seating position has a top tether anchorage, connect Latch Plate (CINCH) — If Equipped the tether strap to the anchorage and tighten the tether 1.
Page 106 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the child restraint has a top tether strap and the If the buckle or the cinching latch plate is too close to the seating position has a top tether anchorage, connect belt path opening of the child restraint, you may have the tether strap to the anchorage and tighten the tether trouble tightening the seat belt.
Page 107 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Installing Child Restraints Using The Top Tether Anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage.
Page 108 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
Page 109 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 WARNING! The top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. Installing Child Restraints Using The Top Tether Anchorage —...
Page 110: Engine Break-In Recommendations
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Air Bags deploying in the front seat could harm your pet. Wide-open throttle acceleration in low gear can be detri- An unrestrained pet will be thrown about and possibly mental and should be avoided.
Page 111: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 NOTE: A new engine may consume some oil during its WARNING! first few thousand miles (kilometers) of operation. This • Do not leave children or animals inside parked should be considered a normal part of the break-in and not interpreted as an indication of difficulty.
Page 112: Exhaust Gas
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 113: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 Safety Checks You Should Make Inside The dealer. If the light stays on, flickers, or comes on while Vehicle driving, have the system checked by an authorized dealer. Seat Belts Defroster Inspect the belt system periodically, checking for cuts, frays, and loose parts.
Page 114 112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 115: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 117: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS MIRRORS ......123 Heated Mirrors — If Equipped ...127 Inside Day/Night Mirror .
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS ......138 60/40 Split Rear Seat ....154 Power Seats —...
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Automatic High Beam — If Equipped ..166 Ambient Light......172 Daytime Running Lights —...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER TILT/TELESCOPING STEERING Activating Adaptive Cruise Control (ACC)..191 COLUMN — IF EQUIPPED ....180 To Activate ......192 HEATED STEERING WHEEL —...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Normal (Fixed Speed) Cruise Control Mode . . .210 PARKSENSE® FRONT AND REAR PARK ASSIST — IF EQUIPPED ... .228 FORWARD COLLISION WARNING (FCW) WITH MITIGATION —...
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning ParkView® On Or Off — With Troubleshooting Tips ....251 Uconnect® 8.4/8.4A....241 General Information.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 COMMANDVIEW® SUNROOF WITH Ignition OFF Operation ....260 POWER SHADE — IF EQUIPPED ..256 Sunroof Fully Closed .
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover — REAR WINDOW FEATURES ....277 If Equipped ......274 Rear Window Wiper/Washer .
Page 125: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting.
Page 126: Automatic Dimming Mirror - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting.
Page 127: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirrors All outside mirrors are hinged and may be moved either to center on the adjacent lane of traffic with a slight forward or rearward to resist damage.
Page 128: Power Mirrors
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the mirror is manually folded after electrically cycled, Power Mirrors a potential extra button push is required to get the The power mirror switch is located on the driver’s side mirrors back to the home position. If the mirror does not door trim panel.
Page 129: Outside Automatic Dimming Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Memory Seat” in “Understanding The Features Of Your Vehicle” for further information. Outside Automatic Dimming Mirrors — If Equipped The drivers outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror.
Page 130: Tilt Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tilt Mirrors In Reverse (Available With Memory Illuminated Vanity Mirrors Seat Only) — If Equipped To access an illuminated vanity mirror, flip down one of Tilt Mirrors in Reverse provides automatic outside mirror the visors.
Page 131: Sun Visor "Slide-On-Rod" Feature - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Sun Visor “Slide-On-Rod” Feature — If Equipped The sun visor “Slide-On-Rod” feature allows for addi- tional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor. 2.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if The BSM detection zone covers approximately one lane on both sides of the vehicle (12 ft or 3.8 m). The zone your vehicle is towing a trailer. Therefore, visually starts at the outside rear view mirror and extends ap- verify the adjacent lane is clear for both your vehicle proximately 23 ft (7 m) to the rear of the vehicle.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Sensor Location (Driver Side Shown) Warning Light Location The BSM system notifies the driver of objects in the The BSM system monitors the detection zone from three detection zones by illuminating the BSM warning light different entry points (side, rear, front) while driving to located in the outside mirrors in addition to sounding an see if an alert is necessary.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles Vehicles that move into your adjacent lanes from either that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 137: Rear Cross Path
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 138: Modes Of Operation
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Modes Of Operation With EVIC sensors are blocked by other structures or vehicles, the Three selectable modes of operation are available in the system will not be able to alert the driver.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Blind Spot Alert NOTE: • Whenever an audible alert is requested by the BSM When operating in Blind Spot Alert mode, the BSM system, the radio is also muted. system will provide a visual alert in the appropriate side view mirror based on a detected object.
Page 140: Understanding The Features Of Your Vehicle Seats
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats — If Equipped Seats are part of the Occupant Restraint System of the Some models may be equipped with eight-way power vehicle. driver and front passenger seats. The power seat switches are located on the outboard side of the seat.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining The Seatback WARNING! (Continued) The angle of the seatback can be adjusted forward or • Do not ride with the seatback reclined so that the rearward. Push the seatback switch forward or rearward, shoulder belt is no longer resting against your chest.
Page 143: Passenger's Power Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Passenger’s Power Seat Adjusting The Seat Up Or Down Some models are equipped with a six-way power pas- The height of the seats can be adjusted up or down. Pull senger seat. The power seat switch is located on the upward or push downward on the seat switch, the seat outboard side of the seat.
Page 144: Power Lumbar - If Equipped
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support.
Page 145: Manual Front Seats Forward/Rearward Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Manual Front Seats Forward/Rearward While sitting in the seat, lift up on the bar located under Adjustment the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired Some models may be equipped with manual front driver position.
Page 146: Manual Front Passenger Seatback Adjustment - Recline
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Passenger Seatback Adjustment — WARNING! Recline Do not ride with the seatback reclined so that the To adjust the seatback, lift the lever located on the shoulder belt is no longer resting against your chest. outboard side of the seat, lean back to the desired In a collision you could slide under the seat belt, position and release the lever.
Page 147: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped with Remote Start Press the “Driver” or “Passenger” seat soft-key once to select HI-level heating. Press the soft-key a second time On models that are equipped with remote start, the to select LO-level heating. Press the soft-key a third time driver’s heated seat and heated steering wheel can be to shut the heating elements OFF.
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Front Heated Seats With Uconnect® 8.4/8.4A — When the HI-level setting is selected, the heater will If Equipped provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the There are two heated seat soft-keys that allow the driver normal HI-level.
Page 150 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Heated Seats You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of On some models, the two outboard seats are equipped heat in use. Two indicator lights will illuminate for with heated seats.
Page 151: Front Ventilated Seats With Uconnect® 8.4/8.4A - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 approximately 60 minutes of continuous operation. At Press the “Driver” or “Passenger” seat soft-key once to that time, the number of illuminated LEDs changes from select HI-level ventilation. Press the soft-key a second two to one, indicating the change.
Page 152: Head Restraints
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury Active Head Restraints are passive, deployable compo- by restricting head movement in the event of a rear- nents, and vehicles with this equipment cannot be readily impact.
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint. To lower the head restraint, press the push forward and rearward. To tilt the head restraint closer to button, located at the base of the head restraint, and push the back of your head, pull forward on the bottom of the downward on the head restraint.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 The center head restraint has limited adjustment. Lift WARNING! (Continued) upward on the head restraint to raise it, or push down- • Active Head Restraints may be deployed if they ward on the head restraint to lower it. are struck by an object such as a hand, foot or loose cargo.
Page 156: 60/40 Split Rear Seat
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Be sure that the front seats are fully upright and WARNING! positioned forward. This will allow the rear seatback to fold down easily. Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a 1.
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: To Raise Rear Seat • Do not fold the 60% rear seat down with the left Raise the rear seatback and lock it into place. If interfer- outboard or rear center seat belt buckled. ence from the cargo area prevents the seatback from fully •...
Page 158: Reclining Rear Seat
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Rear Seat WARNING! To recline the seatback, lift the lever located on the Do not ride with the seatback reclined so that the outboard side of the seat, lean back and release the lever shoulder belt is no longer resting against your chest.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 NOTE: Your vehicle is equipped with two RKE trans- mitters. One RKE transmitter can be linked to memory position 1 and the other transmitter can be linked to memory position 2. The memory seat switch is located on the driver’s door trim panel.
Page 160: Programming The Memory Feature
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming The Memory Feature Vehicles Not Equipped With Keyless Enter-N-Go NOTE: To create a new memory profile, perform the 1. Insert the ignition key fob, and turn the ignition switch following: to the ON/RUN position. Vehicles Equipped With Keyless Enter-N-Go 2.
Page 161: Linking And Unlinking The Remote Keyless Entry Transmitter To Memory
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • The Recall Memory with Remote Linked to Memory To program your RKE transmitters, perform the following: feature can be enabled through the Uconnect® system 1. Remove the Key Fob from the ignition (or change the screen.
Page 162: Memory Position Recall
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Your RKE transmitters can be unlinked to your Driver Two Memory Position Recall memory settings by following steps 1-4 above and press- • To recall the memory setting for driver two using the ing the UNLOCK button (instead of LOCK) on the RKE memory switch, press MEMORY button number 2 on transmitter in Step 4.
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 The distance the driver seat moves depends on where (22.7 mm and 67.7 mm) forward of the rear stop. The you have the driver seat positioned when you remove the seat will return to its previously set position when you Key Fob from the ignition (or change the ignition to OFF, place the ignition to the ACC or RUN position.
Page 164: To Open And Close The Hood
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 2. Reach under the hood, move safety latch to the left and lift the hood. To open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door.
Page 165: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 LIGHTS CAUTION! Headlight Switch To prevent possible damage, do not slam the hood to The headlight switch is located on the left side of the close it. Use a firm downward push at the center of instrument panel, next to the steering wheel.
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore differ- ent lens cleaning procedures must be followed.
Page 167: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Automatic Headlights — If Equipped the wiper system is on. The programmable settings are available in the in the Uconnect® system screen. Refer This system automatically turns the headlights on or off to “Customer- Programmable Features — Uconnect® according to ambient light levels.
Page 168: Automatic High Beam - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic High Beam — If Equipped and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to The automatic high beam system provides increased function improperly. forward lighting at night by automating high beam control through the use of a digital camera mounted on To Activate...
Page 169: Daytime Running Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 To Deactivate Automatic Headlight Leveling — HID Headlights Only 1. Pull the multifunction lever toward you (or rearward This feature prevents the headlights from interfering in car) to manually deactivate the system (normal with the vision of oncoming drivers.
Page 170: Headlight Delay
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Adaptive Headlight System can be turned On or Off Parking Lights And Panel Lights using the Uconnect® System, refer to “Uconnect® Set- tings” in “Understanding Your Instrument Panel” for To turn on the parking lights and instrument further information.
Page 171: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 the headlight switch is rotated to the off position, or the high beam is selected. Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to the its farthest upward position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless...
Page 172: Lights-On Reminder
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE supplement the brightness of the odometer, trip odom- Lights-On Reminder eter, radio and overhead console by rotating the control If the headlights, parking lights, or cargo lights are left on to its farthest position up until you hear a click. This after the ignition is turned OFF, a chime will sound when feature is termed the “Parade”...
Page 173: Front Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Front Map/Reading Lights Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night The front map/reading lights are mounted in the over- time visibility.
Page 174: Courtesy Lights
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy Lights Ambient Light The courtesy lights can be turned on by pressing the top The overhead console is equipped with an ambient light corner of the lens. To turn the lights off, press the lens a feature.
Page 175: Multifunction Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Multifunction Lever Turn Signals The multifunction lever is located on the left side of the Move the multifunction lever up or down and the arrows steering column. on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 176: Flash-To-Pass
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-To-Pass located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Features” in You can signal another vehicle with your headlights by “Understanding The Features Of Your Vehicle”. partially pulling the multifunction lever toward the steer- ing wheel.
Page 177: Windshield Wiper Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Windshield Wiper Operation CAUTION! Rotate the end of the lever to one of the first four detent Always remove any buildup of snow that prevents positions for intermittent settings, the fifth detent for the windshield wiper blades from returning to the low wiper operation and the sixth detent for high wiper “park”...
Page 178: Windshield Washer Operation
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected. Intermittent Wiper Operation NOTE: If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.
Page 179: Mist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 If the end of the lever is pushed while the wipers are in NOTE: The mist feature does not activate the washer the off position, the wipers will operate for several wipe pump; therefore, no washer fluid will be sprayed on the cycles, then turn off.
Page 180: Rain Sensing Wipers - If Equipped
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature may not function properly when Rain Sensing Wipers — If Equipped ice, or dried salt water is present on the windshield. This feature senses moisture on the windshield and •...
Page 181: Tilt/Telescoping Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 • Transmission In NEUTRAL Position — When the TILT/TELESCOPING STEERING COLUMN ignition is ON, and the transmission is in the NEU- This feature allows you to tilt the steering column upward TRAL position, the Rain Sensing system will not or downward.
Page 182: Power Tilt/Telescoping Steering Column - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, push the lever downward POWER TILT/TELESCOPING STEERING (toward the floor). To tilt the steering column, move the COLUMN — IF EQUIPPED steering wheel upward or downward as desired. To This feature allows you to tilt the steering column lengthen or shorten the steering column, pull the steering upward or downward.
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmit- ter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre- programmed positions.
Page 184: Heated Steering Wheel - If Equipped
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HEATED STEERING WHEEL — IF EQUIPPED Touch the “Controls” soft-key then touch the “Heated Steering Wheel” soft-key to turn on the heated steering The steering wheel contains a heating element that helps wheel. Press the “Heated Steering Wheel” soft-key a warm your hands in cold weather.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 during a remote start. Refer to “Remote Starting Sys- tem — If Equipped” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion, or other physical conditions must exercise...
Page 186: Electronic Speed Control - If Equipped
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 20 mph (32 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel.
Page 187: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 188: To Deactivate
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate Pressing the SET (+) button once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANCEL the button results in an increase of 1 mph (1 km/h).
Page 189: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 While the Normal (Fixed Speed) Cruise Control is set, the On steep hills, a greater speed loss or gain may occur so set speed can be decreased by pressing and holding the it may be preferable to drive without Electronic Speed SET - button.
Page 190: Adaptive Cruise Control (Acc) - If Equipped
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADAPTIVE CRUISE CONTROL (ACC) — IF the original set speed) automatically to maintain a EQUIPPED preset following distance, while matching the speed of the vehicle ahead. Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling WARNING! on highways and major roadways.
Page 191 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING! (Continued) WARNING! • The ACC system: You should switch off the ACC system: • Does not react to pedestrians, oncoming vehicles, • When driving in fog, heavy rain, heavy snow, sleet, and stationary objects (e.g., a stopped vehicle in a heavy traffic, and complex driving situations (i.e., traffic jam or a disabled vehicle).
Page 192: Adaptive Cruise Control (Acc) Operation
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Cruise Control system has two control modes: • Adaptive Cruise Control mode for maintaining an appropriate distance between vehicles. • Normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “Normal (Fixed Speed) Cruise Control Mode”...
Page 193: Activating Adaptive Cruise Control (Acc)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 NOTE: Any chassis/suspension or tire size modifica- NOTE: You cannot enable ACC under the following tions to the vehicle will effect the performance of the conditions: Adaptive Cruise Control. • When in Four-Wheel Drive Low. Activating Adaptive Cruise Control (ACC) •...
Page 194: To Activate
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate To turn the system OFF, push and release the Adaptive Cruise Control (ACC) ON/OFF button again. At this Push and release the Adaptive Cruise Control (ACC) time, the system will turn off and the EVIC will display ON/OFF button.
Page 195: To Set A Desired Acc Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 NOTE: ACC cannot be set if there is a stationary vehicle WARNING! in front of your vehicle in close proximity. Leaving the Adaptive Cruise Control (ACC) system on Remove your foot from the accelerator pedal. If you do when not in use is dangerous.
Page 196: To Cancel
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Driver door is opened at low speeds. To Cancel • The driver switches ESC to full-off mode. The following conditions cancel the system: • The brake pedal is applied. NOTE: If ACC is resumed or set with the ESC/TCS off, ESC will automatically be re-engaged.
Page 197: To Resume
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 To Resume WARNING! (Continued) If there is a set speed in memory press the RES (resume) that is too high or too low for prevailing traffic and button and then remove your foot from the accelerator road conditions could cause the vehicle to accelerate pedal.
Page 198: Setting The Following Distance In Acc
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ACC system applies the brakes when following While ACC is set, the set speed can be decreased by pressing the SET - button. the host vehicle and will hold the brakes at a complete stop for 2 seconds and then release.
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Distance Setting 4 Bars (Longest) Distance Setting 3 Bars (Long)
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short)
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 • The vehicle ahead moves out of your lane or view of To increase the distance setting, press the Distance Set- ting — Increase button and release. Each time the button the sensor. is pressed, the distance setting increases by one bar •...
Page 202: Overtake Aid
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “BRAKE” will flash in the EVIC and a chime will sound Overtake Aid while ACC continues to apply its maximum braking When driving with ACC engaged and following a target capacity. vehicle, the system will provide an additional accelera- tion to assist in passing vehicles in front.
Page 203: Adaptive Cruise Control (Acc) Menu
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Adaptive Cruise Control (ACC) Menu Press the SET + or the SET- button (located on the steering wheel) and the following will display in the EVIC: The EVIC displays the current ACC system settings. The EVIC is located in the center of the instrument cluster.
Page 204: Display Warnings And Maintenance
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Display Warnings And Maintenance highly reflective areas (i.e. tunnels with reflective tiles, or ice and snow). The ACC system will recover after the “Wipe Front Radar Sensor In Front Of Vehicle” vehicle has left these areas. Under rare conditions, when Warning the radar is not tracking any vehicles or objects in its path The “ACC / FCW Unavailable Wipe Front Radar Sensor”...
Page 205 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 To keep the ACC System operating properly, it is impor- When the condition that deactivated the system is no tant to note the following maintenance items: longer present, the system will return to the “Adaptive Cruise Control Off”...
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Clean Front Windshield” Warning recover after the vehicle has left these areas. Under rare conditions, when the camera is not tracking any vehicles The “ACC / FCW Limited Functionality Clean Front or objects in its path this warning may temporarily occur. Windshield”...
Page 207 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Removing ACC Sensor For Off-Roading Store the sensor and bracket assembly in a safe location. The wiring and connector must be stowed properly after NOTE: When off-roading, it may be advisable to remove the sensor and bracket assembly is removed.
Page 208: Precautions While Driving With Acc
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service ACC/FCW Warning Offset Driving If the system turns off, and the EVIC displays “ACC/FCW ACC may not detect a vehicle in the same lane that is Unavailable Service Required”or “Cruise/FCW Unavail- offset from your direct line of travel, or a vehicle merging able Service Required”, there may be an internal system in from a side lane.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Turns And Bends When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original Set Speed.
Page 210 208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead.
Page 212: General Information
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary FCC Requirements For Vehicular Radar Systems vehicles. For example, ACC will not react in situations Classification Specifications: where the vehicle you are following exits your lane and 47 C.F.R.
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 To change between the different cruise control modes, To Set A Desired Speed press the ADAPTIVE CRUISE CONTROL (ACC) ON/ Turn the Normal (Fixed Speed) Cruise Control ON. OFF button which turns the ACC and the NORMAL When the vehicle has reached the desired speed, press (Fixed Speed) CONTROL OFF.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the SET (+) button once will result in a 1 mph Pressing the SET (-) button once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of (1 km/h) decrease in set speed.
Page 215: Forward Collision Warning (Fcw) With Mitigation - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 • The vehicle parking brake is applied. FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED • The braking temperature exceeds normal range Forward Collision Warning (FCW) With Mitigation (overheated). Operation • The shift lever is removed from the Drive position. The Forward Collision Warning (FCW) system with To Resume Speed mitigation provides the driver with audible warnings,...
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of autonomous braking to help slow the vehicle and mitigate the potential forward collision. If the driver reacts to the warnings by braking and the system determines that the driver intends to avoid the collision by braking but has not applied sufficient brake force, the...
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 NOTE: Turning FCW ON Or OFF NOTE: The default status of FCW is “On”, this allows • The minimum speed for FCW activation is 5 mph the system to warn you of a possible collision with the (10 km/h).
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The FCW system state is kept in memory from 5. Press the “Active Braking” On or Off soft-key. one key cycle to the next. If the system is turned OFF, it NOTE: A check mark will appear in the selection box to will remain off when the vehicle is restarted.
Page 219 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 5. Press the “FWD Collision Warning” Far or Near NOTE: soft-key for your desired preference. Then press the • The system will retain the last setting selected by the back arrow. driver after ignition shut down. 6.
Page 220: Parksense® Rear Park Assist - If Equipped
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Although the vehicle is still drivable under normal PARKSENSE® REAR PARK ASSIST — conditions, the active braking may not be fully available. IF EQUIPPED Once the condition that limited the system performance The ParkSense® Rear Park Assist system provides visual is no longer present, the system will return to its full and audible indications of the distance between the rear performance state.
Page 221: Parksense® Sensors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 above. The system will become active again if the vehicle Information Center (EVIC) or from the Uconnect® System speed is decreased to speeds less than approximately (if available). Refer to “Electronic Vehicle Information 6 mph (9 km/h).
Page 222: Parksense® Display
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Display The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on When the vehicle is in REVERSE, the EVIC will display the object’s distance and location relative to the vehicle.
Page 223 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Single 1/2 Second Tone Slow Tone...
Page 224 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone Continuous Tone The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 225 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous...
Page 226: Enabling And Disabling Parksense
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling And Disabling ParkSense® Service The ParkSense® Rear Park Assist System ParkSense® can be enabled and disabled with the When the ParkSense® Rear Park Assist System is mal- ParkSense® switch. functioning, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the When the ParkSense®...
Page 227: Cleaning The Parksense® System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 If “PARKSENSE UNAVAILABLE WIPE REAR SENSORS” ParkSense® System Usage Precautions appears in the Electronic Vehicle Information Center NOTE: (EVIC) make sure the outer surface and the underside of • Ensure that the rear bumper is free of snow, ice, mud, the rear fascia/bumper is clean and clear of snow, ice, mud, dirt and debris to keep the ParkSense®...
Page 228 226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • ParkSense®, when on, will reduce the volume of the • On vehicles equipped with a tailgate, ParkSense® radio when it is sounding a tone. should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE.
Page 229 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 WARNING! WARNING! (Continued) • Before using ParkSense®, it is strongly recom- • Drivers must be careful when backing up even mended that the ball mount and hitch ball assem- when using ParkSense®. Always check carefully bly is disconnected from the vehicle when the behind your vehicle, look behind you, and be sure vehicle is not used for towing.
Page 230: Parksense® Front And Rear Park Assist - If Equipped
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE® FRONT AND REAR PARK until the vehicle speed is increased to approximately ASSIST — IF EQUIPPED 7 mph (11 km/h) or above. The system will become active again if the vehicle speed is decreased to speeds The ParkSense®...
Page 231: Parksense® Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 The six ParkSense® sensors, located in the front fascia/ (if equipped). Refer to “Electronic Vehicle Information bumper, monitor the area in front of the vehicle that is Center (EVIC)/Personal Settings (Customer-Program- within the sensors’ field of view. The sensors can detect mable Features)”...
Page 232: Parksense® Display
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Display The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on The warning display will turn ON indicating the system the object’s distance and location relative to the vehicle. status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected.
Page 233 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Single 1/2 Second Tone Slow Tone...
Page 234 232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle:...
Page 235 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than 12 in (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) (30 cm) Front Distance Greater than 47-39 in 39-25 in 25-12 in...
Page 236: Enabling And Disabling Parksense
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Park Assist Audible Alerts Enabling And Disabling ParkSense® ParkSense® will turn off the Front Park Assist audible ParkSense® can be enabled and disabled with the alert (chime) after approximately 3 seconds when an ParkSense®...
Page 237: Service The Parksense® Park Assist System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Service The ParkSense® Park Assist System Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the ParkSense® System is malfunctioning, the instrument cluster will actuate a single chime, once per If PARKSENSE UNAVAILABLE WIPE REAR SENSORS ignition cycle, and it will display the PARKSENSE or PARKSENSE UNAVAILABLE WIPE FRONT SEN-...
Page 238: Parksense® System Usage Precautions
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • ParkSense®, when on, will reduce the volume of the ParkSense® System Usage Precautions radio when it is sounding a tone. NOTE: • Clean the ParkSense® sensors regularly, taking care • Ensure that the front and rear bumper are free of snow, not to scratch or damage them.
Page 239 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 • On vehicles equipped with a tailgate, ParkSense® WARNING! should be disabled when the tailgate is in the lowered • Drivers must be careful when backing up even or open position. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle.
Page 240: Parkview® Rear Back Up Camera - If Equipped
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW® REAR BACK UP CAMERA — WARNING! (Continued) IF EQUIPPED • Before using ParkSense®, it is strongly recom- Your vehicle may be equipped with the ParkView® Rear mended that the ball mount and hitch ball assem- Back Up Camera that allows you to see an on-screen bly is disconnected from the vehicle when the image of the rear surroundings of your vehicle whenever...
Page 241 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 When the vehicle is shifted out of REVERSE (with camera When displayed, dynamic grid lines will illustrate the delay turned ON), The rear view image with dynamic width of the vehicle while a dashed center-line will grid lines will be displayed for up to 10 seconds after indicate the center of the vehicle to assist with aligning to shifting out of REVERSE unless the forward vehicle...
Page 242: Turning Parkview® On Or Off - With Uconnect® 5.0
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be Drivers must be careful when backing up even when driven slowly when using ParkView® to be able to using the ParkView® Rear Back Up Camera. Always stop in time when an obstacle is seen.
Page 243: Turning Parkview® On Or Off - With Uconnect® 8.4/8.4A
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 NOTE: A check mark will appear in the selection box to OVERHEAD CONSOLE indicate the system is turned ON. The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Turning ParkView® On Or Off — With Opener (HomeLink®), power liftgate and power sunroof Uconnect®...
Page 244: Front Map/Reading Lights
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will Lights are mounted in the overhead console. Each light also turn on when the UNLOCK button on the RKE is can be turned on by pressing the switch on either side of pressed.
Page 245: Courtesy Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 Courtesy Lights Sunglasses Bin Door The courtesy lights can be turned on by pressing the top At the front of the console a compartment is provided for corner of the lens. To turn the lights off, press the lens a the storage of a pair of sunglasses.
Page 246: Garage Door Opener - If Equipped
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery.
Page 247: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.
Page 248: Programming A Rolling Code
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
Page 249 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 1. Cycle the ignition to the ON/RUN position. attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAIN- 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) ING”...
Page 250: Programming A Non-Rolling Code
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program To reprogram a channel that has been previously trained, while keeping the HomeLink®...
Page 251: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 • To program the remaining two HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
Page 252 250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Continue to press and hold the HomeLink® button, If you unplugged the garage door opener/device for while you press and release (“cycle”), your hand-held programming, plug it back in at this time. transmitter every two seconds until HomeLink®...
Page 253: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 Using HomeLink® Troubleshooting Tips To operate, press and release the programmed HomeLink® If you are having trouble programming HomeLink®, button. Activation will now occur for the programmed here are some of the most common solutions: device (i.e., garage door opener, gate operator, security •...
Page 254: General Information
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following while you are programming the universal trans- two conditions: ceiver.
Page 255: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children unattended in a vehicle, and visors on the overhead console. do not leave the key in the ignition switch (or leave the ignition of a vehicle equipped with Keyless Enter-N-Go™...
Page 256: Opening Sunroof - Express
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express position. The sunroof will close fully and stop automati- cally. This is called “Express Close”. During Express Press the switch rearward and release it within one-half Close operation, any movement of the switch will stop second and the sunroof will open automatically from any the sunroof.
Page 257: Venting Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 NOTE: If three consecutive sunroof close attempts result Wind Buffeting in Pinch Protect reversals, the fourth close attempt will be Wind buffeting can be described as the perception of a Manual Close movement with Pinch Protect disabled. pressure on the ears or a helicopter-type sound in the ears.
Page 258: Ignition Off Operation
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition OFF Operation The power sunroof switches remain active for up to approximately ten minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. The time is programmable. Refer to “Elec- tronic Vehicle Information Center (EVIC)/Personal Set- tings (Customer-Programmable Features)”...
Page 259: Opening Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 Opening Sunroof — Express WARNING! Press the switch rearward and release it within one- • Never leave children unattended in a vehicle, and half second. The sunroof and sunshade will open auto- do not leave the key in the ignition switch (or leave matically from any position.
Page 260: Closing Sunroof - Manual Mode
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE automatically. This is called “Express Close”. During This is called “Express Open”. During Express Open Express Close operation, any movement of the switch operation, any movement of the shade switch will stop the will stop the sunroof.
Page 261: Closing Power Shade - Manual Mode
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 any position. The shade will close fully and stop auto- sunroof will automatically retract. Remove the obstruc- matically. This is called “Express Close”. During Express tion if this occurs. Next, press the switch forward and Close operation, any movement of the switch will stop release to Express Close.
Page 262: Sunroof Maintenance
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance ELECTRICAL POWER OUTLETS Use only a non-abrasive cleaner and a soft cloth to clean Your vehicle is equipped with 12 Volt (13 Amp) power the glass panel. outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories.
Page 263 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 CAUTION! Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.
Page 264 262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In addition to the front power outlet, there is also a power The rear power outlet is located in the right rear cargo outlet located in the storage area of the center console. area.
Page 265 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 NOTE: The rear power outlet can be switched to “bat- tery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel. Power Outlet Fuse Locations 1 —...
Page 266 264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of outlet power from the vehicle’s battery, even when not should be inserted into any 12 Volt outlet.
Page 267: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 POWER INVERTER — IF EQUIPPED There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 Watts.
Page 268: Cupholders
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE inverter should automatically reset. To avoid overloading CUPHOLDERS the circuit, check the power ratings on electrical devices There are two cupholders for the front seat passengers prior to using the inverter. located in the center console. WARNING! To avoid serious injury or death: •...
Page 269: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 There are two cupholders for the rear seat passengers STORAGE located in the fold-down center armrest. Glove Compartment The glove compartment is located on the right side of the instrument panel. Rear Cupholders Glove Compartment...
Page 270: Door Storage
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the glove compartment, pull outward on the Door Storage latch and lower the glove box door. Large storage areas are built into the door panels for easy access. Opened Glove Compartment Door Panel Storage...
Page 271: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 Console Features To open the upper storage compartment, pull upward on the small latch located on the lid. The center console contains both an upper and a lower storage area. Storage Compartment Latches Storage Compartment...
Page 272 270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift upward on the larger of the latches to access the Your vehicle may have an optional CD or DVD player lower storage compartment. located in the center console. Lower Storage Compartment Lower Storage Compartment CD/DVD Player - If Equipped...
Page 273: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 Press in on the flashlight to release it. WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving.
Page 274: Cargo Storage Bins
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To operate the flashlight, press the switch once for high, Cargo Storage Bins twice for low, and a third time to return to off. There are four removable storage bins located in the rear cargo area.
Page 275 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor) to the liftgate opening. Lower Storage Bins Tether Strap...
Page 276: Retractable Cargo Area Cover
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1.
Page 277: Rear Cargo Tie-Downs
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 WARNING! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment.
Page 278 276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Do not carry loads which exceed the load limits • To help protect against personal injury, passengers described on the label attached to the left door or should not be seated in the rear cargo area. The rear left door center pillar.
Page 279: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 REAR WINDOW FEATURES Rotate the center portion of the lever upward to the first detent for intermittent operation and to Rear Window Wiper/Washer the second detent for continuous rear wiper operation. The rear wiper/washer controls are located on the mul- Rotating the center portion upward once more tifunction lever on the left side of the steering column.
Page 280: Rear Window Defroster
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the rear wiper is operating when the ignition is turned NOTE: To prevent excessive battery drain, use the rear OFF, the wiper will automatically return to the “park” window defroster only when the engine is operating. position.
Page 281: Roof Luggage Rack - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 ROOF LUGGAGE RACK — IF EQUIPPED keeping the crossbars parallel to the rack frame. Once the crossbar is in the desired position, retighten the with the The crossbars and siderails are designed to carry the wrench to lock the crossbar into position.
Page 282 280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Travel at reduced speeds and turn corners carefully • To prevent damage to the roof of your vehicle, do when carrying large or heavy loads on the roof not carry any loads on the roof rack without the rack.
Page 283: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..283 EVIC Red Telltales .....304 INSTRUMENT CLUSTER .
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — CLIMATE CONTROLS ....332 IF EQUIPPED ......329 General Overview .
Page 285: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 283 INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Lower Switch Bank 11 — Hood Release 2 — Instrument Cluster 7 — Hazard Switch 12 — Fuel Door Release 3 — Radio 8 — Storage Bin (SD Card, AUX, USB Media Hub) 13 —...
Page 286: Instrument Cluster
284 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 287: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 285 INSTRUMENT CLUSTER DESCRIPTIONS 3. Anti-Lock Brake (ABS) Light 1. Tachometer This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition Indicates the engine speed in revolutions per minute switch is turned to the ON/RUN position and (RPM x 1000).
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL 4. High Beam Indicator NOTE: If either indicator flashes at a rapid rate, check for a defective outside light bulb. Indicates that headlights are on high beam. 8. Speedometer 5. Front Fog Light Indicator — If Equipped Indicates vehicle speed.
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 does not come on when turning the key from OFF to WARNING! ON/RUN, have the condition checked promptly. A malfunctioning catalytic converter, as referenced Certain conditions, poor fuel quality, etc., may illuminate above, can reach higher temperatures than in normal the light after engine start.
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Engine Temperature Indicator CAUTION! This light warns of an overheated engine condi- Driving with a hot engine cooling system could tion. As temperatures rise and the gauge ap- damage your vehicle. If the temperature gauge reads proaches H, this indicator will illuminate and a single “H”...
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 In this case, the light will remain on until the condition WARNING! (Continued) has been corrected. If the problem is related to the brake look under the hood yourself, see “Maintaining Your booster, the ABS pump will run when applying the brake Vehicle”.
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN position. Driving a vehicle with the red brake light on is NOTE: This light shows only that the parking brake is dangerous.
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 vehicle placard or tire inflation pressure label, you should Your vehicle has also been equipped with a TPMS determine the proper tire inflation pressure for those malfunction indicator to indicate when the system is not tires.) operating properly.
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL U.S. Federal regulations require that upon transfer of CAUTION! vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your The TPMS has been optimized for the original odometer needs to be repaired or serviced, the repair equipment tires and wheels.
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 17. Selectable EVIC Menu 19. Vehicle Security Light This area of the cluster will display the EVIC selectable This light will flash rapidly for approximately menu. For further information, refer to “Electronic Ve- 15 seconds when the vehicle theft alarm is hicle Information Center (EVIC) —...
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Electronic Stability Control (ESC) Activation/ NOTE: Malfunction Indicator Light — If Equipped The “ESC Off Indicator Light” and the “ESC Activation/ The “ESC Activation/Malfunction Indicator Malfunction Indicator Light” come on momentarily each Light” in the instrument cluster will come on time the ignition switch is turned to ON/RUN.
Page 297: Electronic Vehicle Information
UNDERSTANDING YOUR INSTRUMENT PANEL 295 ELECTRONIC VEHICLE INFORMATION CENTER This system allows the driver to select a variety of useful (EVIC) information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: The Electronic Vehicle Information Center (EVIC) fea- •...
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL • UP Arrow Button The system allows the driver to select information by pressing the following buttons mounted on the steering Press and release the UP arrow button to scroll wheel: upward through the main menu and sub- menus (Main Gauge, MPH/km/h, Vehicle Info, Terrain, Driver Assist, Fuel Economy, Trip A, Trip B, Audio, Stored Messages, Screen Set Up).
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 • BACK/LEFT Arrow Button 2. Audio / Phone Information and Sub-menu Informa- tion — Whenever there are sub-menus available, the Press and release the LEFT arrow button to position within the sub-menus is shown here. access the information screens or sub-menu screens of a main menu item.
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL • Unstored Messages The main display area will normally display the main menu or the screens of a selected feature of the main This message type is displayed indefinitely or until the menu. The main display area also displays “pop up” condition that activated the message is cleared.
Page 301: Engine Oil Change Indicator System
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Engine Oil Change Indicator System Vehicles Equipped With Keyless Enter-N-Go™ Oil Change Required 1. Without pressing the brake pedal, press the ENGINE START/STOP button and cycle the ignition to the Your vehicle is equipped with an engine oil change ON/ RUN position (Do not start the engine.) indicator system.
Page 302: Electronic Vehicle Information Center (Evic) Messages
300 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Power Steering Electronic Vehicle Information Center (EVIC) Messages • Cruise Off • Front Seatbelts Unbuckled • Cruise Ready • Driver Seatbelt Unbuckled • Cruise Set To XXX MPH • Passenger Seatbelt Unbuckled • Tire Pressure Screen With Low Tire(s) “Inflate Tire to XX” •...
Page 303 UNDERSTANDING YOUR INSTRUMENT PANEL 301 • Right Turn Signal Light Out • Remote Start Aborted Time Expired • Left Turn Signal Light Out • Remote Start Disabled Start to Reset • Turn Signal On • Service Airbag System • Vehicle Not in Park •...
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL • Autostick Unavailable Service Required • Off Road 1 Ride Height Achieved • Automatic Unavailable Use Autostick Service Req. • Off Road 2 Ride Height Achieved • Transmission Getting Hot Press Brake • Entry/Exit Ride Height Achieved •...
Page 305: Evic Amber Telltales
UNDERSTANDING YOUR INSTRUMENT PANEL 303 • Fuel Saved Gal • Windshield Washer Fluid Low Indicator • Fuel Saved L This telltale will turn on to indicate the wind- shield washer fluid is low. The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the •...
Page 306: Evic Red Telltales
304 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Forward Collision Warming EVIC Red Telltales This area will show reconfigurable red telltales. These This light warns the driver of a potential collision with telltales include: the vehicle in front and prompts the driver to take action in order to avoid the collision.
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 • Oil Temperature Warning Light • Electronic Throttle Control (ETC) Light This telltale indicates engine oil temperature is This light informs you of a problem with the high. If the light turns on while driving, stop Electronic Throttle Control (ETC) system.
Page 308: Evic Green Telltales
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Temperature Warning Light • Electric Power Steering Malfunction – If Equipped This light warns of an overheated engine condi- This telltale is on when the Electric Power tion. As temperatures rise and the gauge ap- Steering is not operating and needs service.
Page 309: Evic Selectable Menu Items
UNDERSTANDING YOUR INSTRUMENT PANEL 307 EVIC Selectable Menu Items LEFT or RIGHT arrow button to scroll through the infor- mation sub-menus and press the OK button to select or Press and release the UP or DOWN arrow buttons until reset the following resettable sub-menus: the desired Selectable Menu icon is highlighted in the EVIC.
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Tire PSI is an information only function and cannot be reset. Press and release the LEFT arrow button to return Press and release the UP or DOWN arrow button until to the main menu. “Tire Pressure”...
Page 311 UNDERSTANDING YOUR INSTRUMENT PANEL 309 Hold the OK button to reset all the information. Fuel Economy Trip B Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted. Press and release the Left or Right arrow but- ton until the Trip B icon is highlighted in the EVIC (Toggle left or right to select Trip A or •...
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL Audio Driver Assist Press and release the UP or DOWN arrow Press and release the UP or DOWN arrow button button until the Driver Assist display icon is until the Audio display icon is highlighted in the highlighted in the EVIC.
Page 313: Screen Setup Driver Selectable Items
UNDERSTANDING YOUR INSTRUMENT PANEL 311 Diagnostics — If Equipped Upper Left • None Press and release the UP or DOWN arrow • Compass button until the Diagnostics display icon is • Outside Temp (default setting) highlighted in the EVIC. Press and release the RIGHT arrow button to display the diagnostic •...
Page 314: Uconnect® Access Settings
312 UNDERSTANDING YOUR INSTRUMENT PANEL Upper Right Restore To Defaults (Restores All Settings To Default Settings) • None • Cancel • Compass (default setting) • Okay • Outside Temp Uconnect® ACCESS SETTINGS • Oil Temp The Uconnect® Access system uses a combination of soft •...
Page 315: Hard-Keys
UNDERSTANDING YOUR INSTRUMENT PANEL 313 Hard-Keys Hard-Keys are located below the Uconnect® Access system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instru- ment panel.
Page 316: Soft-Keys
314 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys next to the setting, showing that setting has been se- lected. Once the setting is complete either press the Back Soft-Keys are accessible on the Uconnect® Access display. Arrow soft-key or the Back hard-key to return to the Customer Programmable Features —...
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 • Display Brightness With Headlights ON language soft-key until a check-mark appears next to the language, showing that setting has been selected. Touch When in this display, you may select the brightness with the back arrow soft-key to return to the previous menu. the headlights on.
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL • Touchscreen Beep Clock After pressing the Clock soft-key the following settings When in this display, you may turn on or shut off the will be available. sound heard when a touch screen button (soft-key) is pressed.
Page 319 UNDERSTANDING YOUR INSTRUMENT PANEL 317 • Set Time Minutes • Front Collision Sensitivity — If Equipped When in this display, you may adjust the minutes. The The Front Collision Warning (FCW) feature can be can be Sync with GPS Time soft-key must be unchecked. To set to Far, or set to Near.
Page 320 318 UNDERSTANDING YOUR INSTRUMENT PANEL • Blind Spot Alert (18 km/h). The system can be enabled with Sound Only, or Sound and Display. To change the Park Assist status, touch When this feature is selected, the Blind Spot Alert feature and release the Sound Only or Sounds and Display button.
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 NOTE: If your vehicle has experienced any damage in until a check-mark appears next to setting, showing that the area where the sensor is located, even if the fascia is setting has been selected. Touch the back arrow soft-key not damaged, the sensor may have become misaligned.
Page 322 320 UNDERSTANDING YOUR INSTRUMENT PANEL • Headlights With Wipers — If Equipped the Hill Start Assist soft-key, until a check-mark appears next to setting, showing that setting has been selected. When this feature is selected, and the headlight switch is Touch the back arrow soft-key to return to the previous in the AUTO position, the headlights will turn on ap- menu.
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 to return to the previous menu. Refer to “Lights/ Smart- next to setting, showing that setting has been selected. Beam™ — If Equipped” in “Understanding The Features Touch the back arrow soft-key to return to the previous Of Your Vehicle”...
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Lock Keyless Entry (RKE) transmitter UNLOCK button. When 1st Press Of Key Fob Unlocks is selected, you must press When this feature is selected, the horn will sound when the RKE transmitter UNLOCK button twice to unlock the the door locks are activated.
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 • Passive Entry NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set This feature allows you to lock and unlock the vehicles to ON) when the Remote Keyless Entry (RKE) transmitter door(s) without having to press the Remote Keyless is used to unlock the door.
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL • Auto-On Driver Heated/Ventilated Seat & Steering • Engine Off Power Delay Wheel With Vehicle Start — If Equipped When this feature is selected, the power window switches, When this feature is selected the driver’s heated seat and radio, Uconnect®...
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 Compass Settings – If Equipped After pressing the Compass Settings soft-key the follow- ing settings will be available. • Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map.
Page 328 326 UNDERSTANDING YOUR INSTRUMENT PANEL CAL until the compass is calibrated. You may also setting soft-keys or by selecting any point on the scale calibrate the compass by pressing the ON soft-key and between the + and – soft-keys. Then touch the arrow back completing one or more 360-degree turns (in an area free soft-key.
Page 329 UNDERSTANDING YOUR INSTRUMENT PANEL 327 • Suspension Display Messages Phone/Bluetooth After pressing the Phone/Bluetooth soft-key the follow- When All is selected, all the Air Suspension Alerts will be ing settings will be available. displayed. When Warnings Only is selected only the Air •...
Page 330 328 UNDERSTANDING YOUR INSTRUMENT PANEL • Subscription Information the feature showing the system has been activated or the check-mark is removed showing the system has been New vehicle purchasers or lessees will receive a free deactivated. limited time subscription to SiriusXM Satellite Radio with •...
Page 331: Uconnect® Radios - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 329 Uconnect® RADIOS — IF EQUIPPED STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED For detailed information about your Uconnect® radio refer to your Uconnect® Supplement Manual. The remote sound system controls are located on the rear surface of the steering wheel.
Page 332: Radio Operation
330 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch with a Radio Operation push-button in the center and controls the volume and Pressing the top of the switch will “Seek” up for the next mode of the sound system. Pressing the top of the rocker listenable station and pressing the bottom of the switch switch will increase the volume, and pressing the bottom will “Seek”...
Page 333: Cd/Dvd/Blu-Ray Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 331 CD/DVD/BLU-RAY DISC MAINTENANCE NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating To keep a CD/DVD/Blu-ray disc in good condition, take removed, a hair, moisture or dew on the disc) oversized, the following precautions: or have protection encoding.
Page 334: Climate Controls
332 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS General Overview The air conditioning and heating system is designed to Hard-Keys make you comfortable in all types of weather. This The hard-keys located below the Uconnect® screen. system can be operated through either the Automatic Climate Controls on the instrument panel or through the Uconnect®...
Page 335 UNDERSTANDING YOUR INSTRUMENT PANEL 333 Soft-Keys Button Descriptions (Applies To Both Hard-keys And Soft-keys) Soft-keys are accessible on the Uconnect® system screen. 1. MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 336 334 UNDERSTANDING YOUR INSTRUMENT PANEL 4. AUTO Operation Button An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically Automatically controls the interior cabin temperature by turns off after 10 minutes. adjusting airflow distribution and amount. Performing this function will cause the ATC to switch between CAUTION! manual mode and automatic modes.
Page 337 UNDERSTANDING YOUR INSTRUMENT PANEL 335 7. Passenger Temperature Control Up Button 9. SYNC Provides the passenger with independent temperature Press the Sync soft-key to toggle the Sync feature On/Off. control. Push the hard-key button for warmer tempera- The Sync indicator is illuminated when this feature is ture settings or on the touch-screen, press and slide the enabled.
Page 338 336 UNDERSTANDING YOUR INSTRUMENT PANEL speeds can be selected using either hard-keys or soft-keys Panel Mode as follows: Air comes from the outlets in the instrument Hard-key panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the The blower speed increases as you turn the control center outlets and outboard outlets can be moved up and clockwise from the lowest blower setting.
Page 339 UNDERSTANDING YOUR INSTRUMENT PANEL 337 Floor Mode 13. Driver Temperature Control Down Button Air comes from the floor outlets. A slight amount Provides the driver with independent temperature con- of air is directed through the defrost and side trol. Push the hard-key button for cooler temperature window demister outlets.
Page 340: Climate Control Functions
338 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control Functions (located in front of the radiator), for an accumulation of dirt or insects. Clean with a gentle water spray from A/C (Air Conditioning) behind the radiator and through the condenser. Fabric The Air Conditioning (A/C) button allows the operator front fascia protectors may reduce airflow to the to manually activate or deactivate the air conditioning condenser, reducing air conditioning performance.
Page 341: Automatic Temperature Control (Atc)
UNDERSTANDING YOUR INSTRUMENT PANEL 339 Recirculation Automatic Temperature Control (ATC) When outside air contains smoke, odors, or Automatic Operation high humidity, or if rapid cooling is desired, 1. Press the AUTO hard-key or soft-key button (4) on the you may wish to recirculate interior air by Automatic Temperature Control (ATC) Panel.
Page 342 340 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Manual Operation • It is not necessary to move the temperature settings for The system allows for manual selection of blower speed, air distribution mode, A/C status and recirculation con- cold or hot vehicles. The system automatically adjusts trol.
Page 343: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Operating Tips Winter Operation Use of the air Recirculation mode during Winter months NOTE: Refer to the chart at the end of this section for is not recommended because it may cause window suggested control settings for various weather conditions. fogging.
Page 344 342 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 345 UNDERSTANDING YOUR INSTRUMENT PANEL 343 Control Setting Suggestions for Various Weather Conditions...
Page 347: Starting And Operating
STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....351 AUTOMATIC TRANSMISSION ... .357 Automatic Transmission ....351 Key Ignition Park Interlock.
Page 348 346 STARTING AND OPERATING Shift Positions ......371 OFF-ROAD DRIVING TIPS ....386 Shifting Procedures .
Page 349 STARTING AND OPERATING 347 FUEL SAVER TECHNOLOGY 5.7L ENGINE Hill Descent Control (HDC) — Four-Wheel Drive ONLY – IF EQUIPPED ....395 Models With MP3023 Two-Speed Transfer Case Only .
Page 350 348 STARTING AND OPERATING TIRES — GENERAL INFORMATION..422 Tire Spinning ......429 Tire Pressure .
Page 351 STARTING AND OPERATING 349 5.7L Engine – If Equipped ....442 Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles ..448 Reformulated Gasoline .
Page 352 350 STARTING AND OPERATING Trailer Towing Weights RECREATIONAL TOWING (Maximum Trailer Weight Ratings) ..461 (BEHIND MOTORHOME, ETC.) ... .471 Trailer And Tongue Weight ....462 Towing This Vehicle Behind Another Vehicle .
Page 353: Starting Procedures
STARTING AND OPERATING 351 STARTING PROCEDURES Automatic Transmission Before starting your vehicle, adjust your seat, adjust the The shift lever must be in the NEUTRAL or PARK inside and outside mirrors, fasten your seat belt, and if position before you can start the engine. Apply the brakes present, instruct all other occupants to buckle their seat before shifting into any driving gear.
Page 354: Keyless Enter-N-Go
352 STARTING AND OPERATING Using Fob With Integrated Key (Tip Start) Keyless Enter-N-Go™ NOTE: Normal starting of either a cold or a warm This feature allows the driver to oper- engine is obtained without pumping or pressing the ate the ignition switch with the push accelerator pedal.
Page 355 STARTING AND OPERATING 353 3. The system takes over and attempts to start the 3. If the shift lever is not in PARK, the ENGINE START/ vehicle. If the vehicle fails to start, the starter will STOP button must be held for two seconds and vehicle disengage automatically after 10 seconds.
Page 356: Extreme Cold Weather (Below -20°F Or −29°C)
354 STARTING AND OPERATING ENGINE START/STOP Button Functions – With Extreme Cold Weather (Below –20°F Or −29°C) Driver’s Foot OFF The Brake Pedal (In PARK Or To ensure reliable starting at these temperatures, use of NEUTRAL Position) an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended.
Page 357 STARTING AND OPERATING 355 3. Press and release the ENGINE START/STOP button WARNING! (Continued) once. • If the vehicle has a discharged battery, booster The starter motor will engage automatically, run for cables may be used to obtain a start from a booster 10 seconds, and then disengage.
Page 358: After Starting
356 STARTING AND OPERATING The starter motor will disengage automatically in 10 sec- The engine block heater must be plugged in at least one onds. Once this occurs, release the accelerator pedal, turn hour to have an adequate warming effect on the engine. the ignition switch to the LOCK position, wait 10 to The engine block heater cord is located: 15 seconds, then repeat the “Normal Starting”...
Page 359: Automatic Transmission
STARTING AND OPERATING 357 AUTOMATIC TRANSMISSION WARNING! • Unintended movement of a vehicle could injure CAUTION! those in or near the vehicle. As with all vehicles, Damage to the transmission may occur if the follow- you should never exit a vehicle while the engine is ing precautions are not observed: running.
Page 360: Key Ignition Park Interlock
358 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL • Children should be warned not to touch the park- if the engine speed is higher than idle speed. If ing brake, brake pedal or the shift lever. •...
Page 361: Brake/Transmission Shift Interlock System
STARTING AND OPERATING 359 Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the shift lever in PARK unless the brakes are applied. To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.
Page 362: Eight-Speed Automatic Transmission
360 STARTING AND OPERATING • The engine idle speed will be lower. brake pedal to shift the transmission out of PARK, or to shift from NEUTRAL into DRIVE or REVERSE when the • The overall driving performance will be more vehicle is stopped or moving at low speeds (refer to conservative.
Page 363 STARTING AND OPERATING 361 The transmission shift lever provides PARK, REVERSE, NEUTRAL, DRIVE and SPORT shift positions. Once in the DRIVE range, tapping the shift lever rearward will toggle between SPORT mode and DRIVE mode. You do not need to press the shift lever button when toggling between DRIVE and SPORT modes.
Page 364 362 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to NOTE: On four-wheel drive vehicles be sure that the allow the selected gear to engage before accelerating. transfer case is in a drive position. This is especially important when the engine is cold. WARNING! PARK •...
Page 365 STARTING AND OPERATING 363 WARNING! (Continued) WARNING! (Continued) • Never leave children alone in a vehicle, or with vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit access to an unlocked vehicle. Allowing children to someone or something.
Page 366 364 STARTING AND OPERATING REVERSE CAUTION! This range is for moving the vehicle backward. Shift into • DO NOT race the engine when shifting from REVERSE only after the vehicle has come to a complete PARK or NEUTRAL into another gear range, as this stop.
Page 367 STARTING AND OPERATING 365 When frequent transmission shifting occurs (such as CAUTION! when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, Towing the vehicle, coasting, or driving for any other or while towing heavy trailers), use the Paddle Shift reason with the transmission in NEUTRAL can cause switches (refer to Paddle Shift Mode in this section) to severe transmission damage.
Page 368 366 STARTING AND OPERATING SPORT illuminated. A message in the instrument cluster will inform the driver of the more serious conditions, and This mode alters the transmission’s automatic shift sched- indicate what actions may be necessary. ule for sportier driving. Upshift speeds are increased to make full use of available engine power.
Page 369 STARTING AND OPERATING 367 5. Restart the engine. braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can 6. Shift into the desired gear range. If the problem is no also provide you with more control during passing, city longer detected, the transmission will return to normal driving, cold slippery conditions, mountain driving, trailer operation.
Page 370 368 STARTING AND OPERATING • If a requested downshift would cause the engine to In Paddle Shift mode, the transmission will shift up or down when (+/-) is manually selected by the driver, over-speed, that shift will not occur. unless an engine lugging or overspeed condition would •...
Page 371: Four-Wheel Drive Operation
STARTING AND OPERATING 369 To disengage Paddle Shift mode, press and hold the (+) FOUR-WHEEL DRIVE OPERATION shift paddle until D or S is once again displayed in the Quadra-Trac I® Operating Instructions/ instrument cluster. You can shift in or out of Paddle Shift Precautions –...
Page 372: Quadra-Trac Ii® Operating Instructions/Precautions - If Equipped
370 STARTING AND OPERATING Quadra-Trac II® Operating Instructions/ When operating your vehicle in 4WD LOW, the engine Precautions – If Equipped speed is approximately three times that of the 4WD HI position at a given road speed. Take care not to overspeed The Quadra-Trac II®...
Page 373: Shift Positions
STARTING AND OPERATING 371 NEUTRAL WARNING! (Continued) This range disengages both the front and rear driveshafts the parking brake. The transfer case NEUTRAL (N) from the powertrain. It is to be used for flat towing position disengages both the front and rear drive- behind another vehicle.
Page 374: Shifting Procedures
372 STARTING AND OPERATING Shifting Procedures 4WD HI To 4WD LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the ON position or the engine running, shift the transmission into NEUTRAL, and press the “4WD LOW”...
Page 375 STARTING AND OPERATING 373 NOTE: If shift conditions/interlocks are not met, or a NOTE: transfer case motor temperature protection condition • If shift conditions/interlocks are not met, or a transfer exists, a “For 4x4 Low Slow Below 3 MPH or 5 KPH Put case motor temperature protection condition exists, a Trans in N Press 4 Low”...
Page 376 374 STARTING AND OPERATING NEUTRAL Shift Procedure will display on the EVIC (Electronic Vehicle Informa- tion Center). Refer to “Electronic Vehicle Information 1. Bring the vehicle to a complete stop, with the engine Center (EVIC)” in “Understanding Your Instrument running. Panel”...
Page 377: Quadra-Drive® Ii System - If Equipped
STARTING AND OPERATING 375 6. After the shift is completed and the NEUTRAL (N) Quadra-Drive® II System – If Equipped light stays on, release the NEUTRAL (N) button. The optional Quadra-Drive® II System features two torque transfer couplings. The couplings include an 7.
Page 378: Selec-Terrain™ - If Equipped
376 STARTING AND OPERATING SELEC-TERRAIN™ — IF EQUIPPED Selec-Terrain™ consists of the following positions: • Snow – Tuning set for additional stability in inclement Description weather. Use on and off road on loose traction surfaces Selec-Terrain™ combines the capabilities of the vehicle such as snow.
Page 379 STARTING AND OPERATING 377 • Sand – Off road calibration for use on low traction • Rock – Off-road calibration only available in 4WD surfaces such as sand or wet grass. Driveline is maxi- Low range. The vehicle is raised (if equipped with Air mized for traction.
Page 380: Electronic Vehicle Information Center (Evic) Display Messages
378 STARTING AND OPERATING Electronic Vehicle Information Center (EVIC) Display Messages When the appropriate conditions exist, a message will appear in the EVIC display. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. QUADRA-LIFT™ — IF EQUIPPED Description The Quadra-Lift™...
Page 381 STARTING AND OPERATING 379 • Normal Ride Height (NRH) – This is the standard • Off-Road 2 (OR2) (Raises the vehicle approximately position of the suspension and is meant for normal 2.6 in (65 mm) – This position is intended for off- driving.
Page 382 380 STARTING AND OPERATING return to NRH from Aero Mode if the vehicle speed (40 km/h) the Entry/Exit Mode change will be can- remains between 30 mph (48 km/h) and 35 mph celled. To exit Entry/Exit Mode, press the “Up” button (56 km/h) for greater than 20 seconds or if the vehicle once while in Park Mode or drive the vehicle over speed falls below 30 mph (48 km/h).
Page 383 STARTING AND OPERATING 381 The system requires that the engine be running for all To assist with changing a spare tire, the Quadra-Lift™ air changes. When lowering the vehicle all of the doors, suspension system has a feature which allows the auto- including the liftgate, must be closed.
Page 384: Air Suspension Modes
382 STARTING AND OPERATING Air Suspension Modes Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further The Air Suspension system has multiple modes to protect information. the system in unique situations: Wheel Alignment Mode Tire/Jack Mode Before performing a wheel alignment this mode must be To assist with changing a spare tire, the air suspension enabled.
Page 385: Electronic Vehicle Information Center (Evic) Display Messages
STARTING AND OPERATING 383 Electronic Vehicle Information Center (EVIC) When lowering, if multiple indicators are flashing on the Display Messages Up button the lowest solid indicator lamp is the posi- tion the system is working to achieve. When the appropriate conditions exist, a message will appear in the EVIC display.
Page 386 384 STARTING AND OPERATING • Entry/Exit Mode – Indicator lamp 3 will be illumi- requested level by one position down to a minimum of Park Mode or the lowest position allowed based on nated when the vehicle is in Entry/Exit Mode. If current conditions (i.e.
Page 387: On-Road Driving Tips
STARTING AND OPERATING 385 • Transport Mode - No indicator lamps will be illumi- An advantage of the higher ground clearance is a better nated. Customer driving will disable Transport Mode. view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as •...
Page 388: Off-Road Driving Tips
386 STARTING AND OPERATING OFF-ROAD DRIVING TIPS NOTE: Prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with seven quarter turn fasteners and can be removed by hand. The front license plate bracket must be removed first if equipped.
Page 389: Quadra-Lift™ - If Equipped
STARTING AND OPERATING 387 Quadra-Lift™ – If Equipped When To Use 4WD LOW Range – If Equipped When off-roading, it is recommended that the lowest When off-road driving, shift to 4WD LOW for additional useable vehicle height that will clear the current obstacle traction.
Page 390: Driving Through Water
388 STARTING AND OPERATING Driving Through Water Driving through water more than a few inches/centi- meters deep will require extra caution to ensure safety Although your vehicle is capable of driving through and prevent damage to your vehicle. If you must drive water, there are a number of precautions that must be through water, try to determine the depth and the bottom considered before entering the water.
Page 391: Driving In Snow, Mud And Sand
STARTING AND OPERATING 389 Standing Water Refer to “Four-Wheel Drive Operation” in “Starting and Operating” for further information. Do not shift to a Avoid driving in standing water deeper than 20 inches lower gear than necessary to maintain forward motion. (51 cm), and reduce speed appropriately to minimize Over-revving the engine can spin the wheels and traction wave effects.
Page 392: Traction Downhill
390 STARTING AND OPERATING If you stall or begin to lose forward motion while Remember, never drive diagonally across a hill always climbing a steep hill, allow your vehicle to come to a stop drive straight up or down. and immediately apply the brakes. Restart the engine, If the wheels start to slip as you approach the crest of a and shift into REVERSE.
Page 393: After Driving Off-Road
STARTING AND OPERATING 391 • After extended operation in mud, sand, water, or After Driving Off-Road similar dirty conditions, have the radiator, fan, brake Off-road operation puts more stress on your vehicle than rotors, wheels, brake linings, and axle yokes inspected does most on-road driving.
Page 394: Power Steering
392 STARTING AND OPERATING POWER STEERING If the “SERVICE POWER STEERING SYSTEM” message and a flashing icon are displayed on 3.6L Engine the EVIC screen, it indicates that the vehicle Your vehicle is equipped with an electro-hydraulic power needs to be taken to the dealer for service. It is steering system that will give you good vehicle response likely the vehicle has lost power steering assistance.
Page 395: L Engine
STARTING AND OPERATING 393 NOTE: NOTE: • Even if power steering assistance is no longer opera- • Increased noise levels at the end of the steering wheel tional, it is still possible to steer the vehicle. Under travel are considered normal and do not indicate that these conditions there will be a substantial increase in there is a problem with the power steering system.
Page 396: Power Steering Fluid Check
394 STARTING AND OPERATING CAUTION! CAUTION! Prolonged operation of the steering system at the end Do not use chemical flushes in your power steering of the steering wheel travel will increase the steering system as the chemicals can damage your power fluid temperature and it should be avoided when steering components.
Page 397: Fuel Saver Technology 5.7L Engine Only - If Equipped
STARTING AND OPERATING 395 FUEL SAVER TECHNOLOGY 5.7L ENGINE ONLY – IF EQUIPPED This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required.
Page 398 396 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the transmis- • Never use the PARK position as a substitute for the sion is placed in gear, the “Brake Warning Light” will parking brake. Always apply the parking brake flash.
Page 399: Electronic Brake Control System
STARTING AND OPERATING 397 WARNING! (Continued) CAUTION! • Do not leave the key fob in or near the vehicle (or If the “Brake Warning Light” remains on with the in a location accessible to children), and do not parking brake released, a brake system malfunction leave the ignition of a vehicle equipped with is indicated.
Page 400: Anti-Lock Brake System (Abs)
398 STARTING AND OPERATING Also, your vehicle is equipped with Trailer Sway Control WARNING! (TSC), Hill Start Assist (HSA), Brake Lock Differential (BLD), Ready Alert Braking, Rain Brake Support and, if it The ABS cannot prevent the natural laws of physics has four-wheel drive with the MP 3023 two-speed transfer from acting on the vehicle, nor can it increase the case, Hill Descent Control (HDC), Selec Speed Control...
Page 401: Brake Assist System (Bas)
STARTING AND OPERATING 399 A feature of the TCS system, Brake Limited Differential quickly results in the best BAS assistance. To receive the (BLD), functions similar to a limited-slip differential and benefit of the system, you must apply continuous brak- controls the wheel spin across a driven axle.
Page 402: Electronic Roll Mitigation (Erm)
400 STARTING AND OPERATING Electronic Roll Mitigation (ERM) WARNING! This system anticipates the potential for wheel lift by Many factors, such as vehicle loading, road condi- monitoring the driver’s steering wheel input and the tions, and driving conditions, influence the chance speed of the vehicle.
Page 403 STARTING AND OPERATING 401 counteracting the oversteer or understeer condition. The “ESC Activation/Malfunction Indicator Light” also Engine power may also be reduced to help the vehicle flashes when the TCS is active. If the “ESC Activation/ maintain the desired path. Malfunction Indicator Light”...
Page 404 402 STARTING AND OPERATING 4WD HIGH range, the ESC system will be in this “On” WARNING! (Continued) mode. This mode should be used for most driving attentive, and skillful driver can prevent collisions. situations. ESC should only be turned to “Partial Off” The capabilities of an ESC equipped vehicle must mode for specific reasons as noted below.
Page 405: Trailer Sway Control (Tsc)
STARTING AND OPERATING 403 NOTE: To improve the vehicle’s traction when driving Trailer Sway Control (TSC) with snow chains, or starting off in deep snow, sand, or TSC uses sensors in the vehicle to recognize an exces- gravel, it may be desirable to switch to the “Partial Off” sively swaying trailer and will take the appropriate mode by pressing the “ESC OFF”...
Page 406: Hill Start Assist (Hsa)
404 STARTING AND OPERATING HSA Activation Criteria WARNING! The following criteria must be met in order for HSA to If TSC activates while driving, slow the vehicle down, activate: stop at the nearest safe location, and adjust the trailer • Vehicle must be stopped. load to eliminate trailer sway.
Page 407 STARTING AND OPERATING 405 WARNING! WARNING! (Continued) brake pedal is released, there may not be enough There may be situations on minor hills (i.e., less than brake pressure to hold the vehicle and trailer on a 8%), with a loaded vehicle, or while pulling a trailer, hill and this could cause a collision with another when the system will not activate and slight rolling vehicle or object behind you.
Page 408: Ready Alert Braking - If Equipped
406 STARTING AND OPERATING HSA Off Rain Brake Support – If Equipped If you wish to turn off the HSA system, it can be done Rain Brake Support may improve braking performance using the Uconnect® Access Settings. Refer to “Uconnect® in wet conditions.
Page 409 STARTING AND OPERATING 407 When HDC is enabled, the HDC icon will be illuminated HDC Operation In 4WD Low Range in the instrument cluster. HDC will automatically apply To enable HDC, press the HDC switch. The HDC icon the brakes to control downhill speed to the selected level will be illuminated in the instrument cluster and HDC when necessary on grades greater than approximately will function.
Page 410: Select Speed Control (Ssc) - Four-Wheel Drive Models With Mp3023 Two-Speed Transfer Case Only
408 STARTING AND OPERATING • 8th = 5 mph (8 km/h) WARNING! • REVERSE = .6 mph (1 km/h) HDC is only intended to assist the driver in control- • NEUTRAL = 1.2 mph (2 km/h) ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and •...
Page 411 STARTING AND OPERATING 409 The SSC speed may be adjusted by the driver to suit the 4WD Low Range Set Speeds driving conditions. The speed corresponds to the trans- • 1st = .6 mph (1 km/h) mission gear selected. SSC operation can be overridden •...
Page 412: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
410 STARTING AND OPERATING SSC is intended for low speed off-road driving only. At running. If the “ESC Activation/Malfunction Indicator vehicle speeds above 20 mph (32 km/h), SSC remains Light” comes on continuously with the engine running, a enabled but does not function. If the vehicle speed is malfunction has been detected in the ESC system.
Page 413: Tire Safety Information
STARTING AND OPERATING 411 NOTE: TIRE SAFETY INFORMATION • The “ESC Activation/Malfunction Indicator Light” Tire Markings and the “ESC OFF Indicator Light” come on momen- tarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESC system will be ON even if it was turned off previously.
Page 414 412 STARTING AND OPERATING • Temporary spare tires are spares designed for tempo- NOTE: rary emergency use only. Temporary high pressure • P (Passenger) - Metric tire sizing is based on U.S. compact spare tires have the letter “T” or “S” molded design standards.
Page 415 STARTING AND OPERATING 413 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 416 414 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 417: Tire Identification Number (Tin)
STARTING AND OPERATING 415 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire, the outboard side, then you will find it on the inboard however, the date code may only be on one side.
Page 418: Tire Terminology And Definitions
416 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) — 01 means the year 2001 — Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
Page 419: Tire Loading And Tire Pressure
STARTING AND OPERATING 417 Term Definition Recommended Cold Tire Vehicle manufacturer’s recommended cold tire inflation pressure as shown on Inflation Pressure the tire placard. Tire Placard A paper label permanently attached to the vehicle describing the vehicle’s loading capacity, the original equipment tire sizes and the recommended cold tire inflation pressures.
Page 420 418 STARTING AND OPERATING Tire And Loading Information Placard 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading...
Page 421 STARTING AND OPERATING 419 To determine the maximum loading conditions of your 4. The resulting figure equals the available amount of vehicle, locate the statement “The combined weight of cargo and luggage load capacity. For example, if occupants and cargo should never exceed XXX lbs or “XXX”...
Page 422 420 STARTING AND OPERATING NOTE: • The following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle.
Page 423 STARTING AND OPERATING 421...
Page 424: Tires - General Information
422 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 425: Tire Inflation Pressures
STARTING AND OPERATING 423 stability of the vehicle and can produce a feeling of WARNING! (Continued) sluggish response or over responsiveness in the steering. • Unequal tire pressures from one side of the vehicle Unequal tire pressures from side to side may cause erratic to the other can cause the vehicle to drift to the and unpredictable steering response.
Page 426 424 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, always the winter.
Page 427: Tire Pressures For High Speed Operation
STARTING AND OPERATING 425 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires on speeds, maintaining correct tire inflation pressure is very your vehicle will cause your vehicle to handle poorly.
Page 428: All Season Tires - If Equipped
426 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and on ice. Summer tires will not contain the all season additional information. designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to Damaged Run Flat tires, or Run Flat tires that have do so may adversely affect the safety and handling of experienced a loss of pressure should be replaced imme-...
Page 429: Spare Tire Matching Original Equipped Tire And Wheel - If Equipped
STARTING AND OPERATING 427 original equipment or an authorized tire dealer for Compact Spare Tire – If Equipped recommended safe operating speeds, loading and cold The compact spare is for temporary emergency use only. tire inflation pressures. You can identify if your vehicle is equipped with a While studded tires improve performance on ice, skid compact spare by looking at the spare tire description on and traction capability on wet or dry surfaces may be...
Page 430: Full Size Spare - If Equipped
428 STARTING AND OPERATING Do not install more than one compact spare tire and tire may have limited tread life. When the tread is worn wheel on the vehicle at any given time. to the tread wear indicators, the temporary use full size spare tire needs to be replaced.
Page 431: Tire Spinning
STARTING AND OPERATING 429 Tire Spinning WARNING! When stuck in mud, sand, snow, or ice conditions, do not Limited-use spares are for emergency use only. In- spin your vehicle’s wheels above 30 mph (48 km/h) or stallation of this limited-use spare tire affects vehicle for longer than 30 seconds continuously without stop- handling.
Page 432: Tread Wear Indicators
430 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth Tread wear indicators are in the original equipment tires becomes 1/16 in (2 mm). When the tread is worn to the to help you in determining when your tires should be tread wear indicators, the tire should be replaced.
Page 433: Replacement Tires
STARTING AND OPERATING 431 “Tread Wear Indicators”. Refer to the Tire and Loading WARNING! Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Tires and the spare tire should be replaced after six Speed Symbol for your tire will be found on the original years, regardless of the remaining tread.
Page 434 432 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use a tire with a smaller load index or • Do not use a tire, wheel size or rating other than capacity, other than what was originally equipped that specified for your vehicle. Some combinations on your vehicle.
Page 435: Tire Chains (Traction Devices)
STARTING AND OPERATING 433 TIRE CHAINS (TRACTION DEVICES) CAUTION! Use of traction devices require sufficient tire-to-body clear- To avoid damage to your vehicle or tires, observe the ance. Follow these recommendations to guard against following precautions: damage. • Because of restricted traction device clearance be- •...
Page 436: Tire Rotation Recommendations
434 STARTING AND OPERATING These effects can be reduced by timely rotation of tires. CAUTION! (Continued) The benefits of rotation are especially worthwhile with • Observe the traction device manufacturer’s instruc- aggressive tread designs such as those on On/Off-Road tions on the method of installation, operating speed, type tires.
Page 437: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 435 The suggested rotation method is the “forward-cross” TIRE PRESSURE MONITOR SYSTEM (TPMS) shown in the following diagram. The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the Receiver Module.
Page 438 436 STARTING AND OPERATING • Various Tire Pressure Monitoring System Messages, pressure will also increase as the vehicle is driven - this is which display in the Electronic Vehicle Information normal and there should be no adjustment for this Center (EVIC), and a graphic displaying tire pressures increased pressure.
Page 439 STARTING AND OPERATING 437 The vehicle may need to be driven for up to 20 minutes CAUTION! above 15 mph (24 km/h) to receive this information. • The TPMS has been optimized for the original For example, your vehicle has a recommended cold equipment tires and wheels.
Page 440: Tire Pressure Monitoring Low Pressure Warnings
438 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, NOTE: and the TPMS will monitor the actual tire pressure in • The TPMS is not intended to replace normal tire care the tire. and maintenance, or to provide warning of a tire failure or condition.
Page 441: Service Tpm System Warning
STARTING AND OPERATING 439 Should a low tire condition occur on any of the four active in place of the pressure value(s), indicating which Tire road tire(s), you should stop as soon as possible, and inflate Pressure Monitoring Sensor(s) is not being received. the low tire(s) that is in a different color on the graphic NOTE: Your system can be set to display pressure units display to the vehicle’s recommended cold tire pressure...
Page 442 440 STARTING AND OPERATING 3. Lots of snow or ice around the wheels or wheel NOTE: There is no tire pressure monitoring sensor in the housings. spare tire. The TPMS will not be able to monitor the tire pressure. If you install the spare tire in place of a road tire 4.
Page 443: General Information
STARTING AND OPERATING 441 Telltale Light will flash on and off for 75 seconds and then General Information remain on solid, and the EVIC will display a SERVICE This device complies with Part 15 of the FCC rules and TPM SYSTEM message for five seconds and then dis- RSS 210 of Industry Canada.
Page 444: Fuel Requirements
442 STARTING AND OPERATING FUEL REQUIREMENTS recommends the use of 89 octane for optimum perfor- mance. The use of premium gasoline is not recommended, 3.6L Engine – If Equipped as it will not provide any benefit over regular gasoline in these engines.
Page 445: Reformulated Gasoline
STARTING AND OPERATING 443 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner DO NOT use gasoline containing Methanol or gaso- burning gasoline referred to as “Reformulated Gasoline.” line containing more than 10% Ethanol. Use of these Reformulated gasolines contain oxygenates and are spe- blends may result in starting and driveability prob- cifically blended to reduce vehicle emissions and im-...
Page 446: E-85 Usage In Non-Flex Fuel Vehicles
444 STARTING AND OPERATING • disconnect and reconnect the battery to reset the E-85 Usage In Non-Flex Fuel Vehicles engine controller memory Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol content More extensive repairs will be required for prolonged may void the vehicle’s warranty.
Page 447: Materials Added To Fuel
STARTING AND OPERATING 445 Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to • An out-of-tune engine or certain fuel or ignition contain effective detergent additives. Use of additional malfunctions can cause the catalytic converter to detergents or other additives is not needed under normal overheat.
Page 448: Carbon Monoxide Warnings
446 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 449: Ethanol Fuel (E-85)
STARTING AND OPERATING 447 Ethanol Fuel (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and Only vehicles with the E-85 fuel filler door label can 15% unleaded gasoline. operate on E-85. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
Page 450: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
448 STARTING AND OPERATING • Some additives used in regular gasoline are not fully For best results, a refueling pattern that avoids alternating between E-85 and unleaded gasoline is recommended. compatible with E-85 and may form deposits in your engine. To eliminate driveability issues that may be When you do switch fuel types it is recommended that: caused by these deposits, a supplemental gasoline addi- •...
Page 451: Starting
STARTING AND OPERATING 449 Starting Replacement Parts The characteristics of E-85 fuel make it unsuitable for use Many components in your Flexible Fuel Vehicle (FFV) are when ambient temperatures fall below 0°F (-18°C). In the designed to be compatible with ethanol. Always be sure range of 0°F (-18°C) to 32°F (0°C), you may experience an that your vehicle is serviced with correct ethanol com- increase in the time it takes for your engine to start, and...
Page 452: Adding Fuel
450 STARTING AND OPERATING ADDING FUEL 1. Press the fuel filler door release switch (located under the headlamp switch). Fuel Filler Door 3. There is no fuel filler cap. A flapper door inside the pipe seals the system. 4. Insert the fuel nozzle fully into the filler pipe – the nozzle Fuel Filler Door Release Switch opens and holds the flapper door while refueling.
Page 453 STARTING AND OPERATING 451 • Pour fuel into funnel opening. NOTE: Only the correct size nozzle opens the latches allowing the flapper door to open. • Remove funnel from filler pipe, clean off prior to 5. Fill the vehicle with fuel – when the fuel nozzle putting back in the spare tire storage area.
Page 454: Emergency Fuel Filler Door Release
452 STARTING AND OPERATING 4. Remove the storage bin. WARNING! (Continued) 5. Pull the release cable. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
Page 455: Vehicle Loading
STARTING AND OPERATING 453 VEHICLE LOADING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Certification Label Payload As required by National Highway Traffic Safety Admin- istration regulations, your vehicle has a certification label The payload of a vehicle is defined as the allowable load affixed to the driver’s side door or pillar.
Page 456 454 STARTING AND OPERATING Tire Size values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are The tire size on the Vehicle Certification Label represents added. the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Page 457: Trailer Towing
STARTING AND OPERATING 455 specified weight limitations are met. Store the heavier TRAILER TOWING items down low and be sure that the weight is distributed In this section you will find safety tips and information equally. Stow all loose items securely before driving. on limits to the type of towing you can reasonably do with your vehicle.
Page 458 456 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle WARNING! (Continued) Certification Label” in “Starting and Operating” for standard weight-carrying hitch, you could lose control further information. of your vehicle and cause a collision. Gross Trailer Weight (GTW) Gross Combination Weight Rating (GCWR) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem-...
Page 459 STARTING AND OPERATING 457 Trailer Sway Control WARNING! The trailer sway control can be a mechanical telescoping It is important that you do not exceed the maximum link that can be installed between the hitch receiver and front or rear GAWR. A dangerous driving condition the trailer tongue that typically provides adjustable fric- can result if either rating is exceeded.
Page 460 458 STARTING AND OPERATING Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted weight-distributing hitch age through spring (load) bars. They are typically used system may reduce handling, stability, and braking for heavier loads, to distribute trailer tongue weight to performance, and could result in a collision.
Page 461 STARTING AND OPERATING 459 Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct)
Page 462: Trailer Hitch Classification
460 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 463: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 461 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain: Max. GTW Max. Trailer Tongue Engine Model Frontal Area (Gross Trailer Wt.) Wt. (See Note) 3.6L 55 sq ft (5.11 sq m) 6,200 lbs (2 812 kg)
Page 464: Trailer And Tongue Weight
462 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer.
Page 465: Towing Requirements
STARTING AND OPERATING 463 NOTE: Remember that everything put into or on the CAUTION! trailer adds to the load on your vehicle. Also, additional • Do not tow a trailer at all during the first 500 miles factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
Page 466 464 STARTING AND OPERATING WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to a collision. Follow these vehicle and trailer. Always connect the chains to guidelines to make your trailer towing as safe as the hook retainers of the vehicle hitch.
Page 467 STARTING AND OPERATING 465 “Tires – General Information” in “Starting and Oper- WARNING! (Continued) ating” for proper tire inflation procedures. • Total weight must be distributed between the tow • Check the trailer tires for proper tire inflation pres- vehicle and the trailer such that the following four sures before trailer usage.
Page 468 466 STARTING AND OPERATING Towing Requirements – Trailer Brakes CAUTION! • Do not interconnect the hydraulic brake system or If the trailer weighs more than 1,000 lbs (454 kg) vacuum system of your vehicle with that of the trailer. loaded, it should have its own brakes and they This could cause inadequate braking and possible should be of adequate capacity.
Page 469 STARTING AND OPERATING 467 The electrical connections are all complete to the vehicle WARNING! (Continued) but you must mate the harness to a trailer connector. • Towing any trailer will increase your stopping Refer to the following illustrations. distance. When towing you should allow for addi- tional space between your vehicle and the vehicle in front of you.
Page 470: Towing Tips
468 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic Transmission The DRIVE range can be selected when towing. The transmission controls include an adaptive drive strategy to avoid frequent shifting when towing.
Page 471 STARTING AND OPERATING 469 AutoStick® Electronic Speed Control – If Equipped • When using the AutoStick® shift control, select the • Do not use in hilly terrain or with heavy loads. highest gear that allows for adequate performance and • When using the speed control, if you experience speed avoids frequent downshifts.
Page 472: Snow Plow
470 STARTING AND OPERATING Cooling System SNOW PLOW To reduce potential for engine and transmission over- Snow plows, winches, and other aftermarket equipment heating, take the following actions: should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the City Driving front end structure.
Page 473: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 471 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Wheel OFF the Two-Wheel Drive Models Four-Wheel Drive Models Condition Ground Flat Tow NONE NOT ALLOWED See Instructions • Transmission in PARK • Transfer case in NEUTRAL (N) •...
Page 474: Recreational Towing - Two-Wheel Drive Models
472 STARTING AND OPERATING Recreational Towing – Two-Wheel Drive Models 6. Install a suitable clamping device, designed for tow- ing, to secure the front wheels in the straight position. DO NOT flat tow this vehicle. Damage to the drivetrain will result. CAUTION! Recreational towing (for two-wheel drive models) is Towing with the rear wheels on the ground will...
Page 475 STARTING AND OPERATING 473 CAUTION! CAUTION! (Continued) • Do not use a bumper-mounted clamp-on tow bar on • DO NOT dolly tow any 4WD vehicle. Internal dam- your vehicle. The bumper face bar will be damaged. age to the transmission or transfer case will occur if a dolly is used when recreational towing.
Page 476 474 STARTING AND OPERATING Use the following procedure to prepare your vehicle for 4. If vehicle is equipped with Quadra-Lift™ air suspen- recreational towing. sion, ensure the vehicle is set to Normal Ride Height. 5. Using a ballpoint pen or similar object, press and hold CAUTION! the recessed transfer case NEUTRAL (N) button (lo- cated by the selector switch) for four seconds.
Page 477 STARTING AND OPERATING 475 8. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 9. Shift the transmission back into NEUTRAL 10. With the transmission and transfer case in NEU- TRAL, press and hold the ENGINE START/STOP button until the engine turns off.
Page 478 476 STARTING AND OPERATING • If the vehicle is equipped with Quadra-Lift™ air NOTE: suspension, the engine should be started and left • Steps 1 through 4 are requirements that must be met running for a minimum of 60 seconds (with all the before pressing the NEUTRAL (N) button, and must doors closed) at least once every 24 hours.
Page 479 STARTING AND OPERATING 477 6. Using a ballpoint pen or similar object, press and hold 8. After the NEUTRAL (N) button has been released, the the recessed transfer case NEUTRAL (N) button (lo- transfer case will shift to the position indicated by the cated by the selector switch) for one second.
Page 480 478 STARTING AND OPERATING NOTE: • Steps 1 through 5 are requirements that must be met prior to pressing the NEUTRAL (N) button, and must continue to be met until the shift has been completed. If any of these requirements are not met prior to pressing the NEUTRAL (N) button or are no longer met during the shift, the NEUTRAL (N) indicator light will flash continuously until all requirements are met...
Page 481: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...480 Preparations For Jump-Start ....492 IF YOUR ENGINE OVERHEATS ... .480 Jump-Starting Procedure .
Page 482: Hazard Warning Flashers
480 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the switch bank just above the climate controls. potential for overheating by taking the appropriate action. •...
Page 483: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 481 JACKING AND TIRE CHANGING CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT • Do not attempt to change a tire on the side of the (H), pull over and stop the vehicle.
Page 484: Jack Location
482 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
Page 485: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 483 Preparations For Jacking 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. CAUTION! 4. Place the shift lever into PARK. Always lift or jack the vehicle from the correct jacking points. Failure to follow this information could cause 5.
Page 486: Jacking Instructions
484 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. • Do not get under the vehicle when it is on a jack. If Carefully follow these tire changing warnings to help prevent personal injury or damage to your you need to get under a raised vehicle, take it to a...
Page 487 WHAT TO DO IN EMERGENCIES 485 Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. Jack and Tool Assembly 1. Remove the spare tire, jack, and tools from storage. CAUTION! 2.
Page 488 486 WHAT TO DO IN EMERGENCIES 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. Jacking Locations Lift Point Symbol On Sill Molding...
Page 489 WHAT TO DO IN EMERGENCIES 487 5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged.
Page 490 488 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Remove the lug nuts and wheel. 8.
Page 491 WHAT TO DO IN EMERGENCIES 489 9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks. 10. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage.
Page 492 490 WHAT TO DO IN EMERGENCIES 12. Remove the small center cap and securely store the 13. Have the aluminum road wheel and tire repaired as road wheel in the cargo area. soon as possible, properly secure the spare tire with the special wing nut torqued to 3.7 ft-lbs (5 N·m), reinstall the jack and tool kit foam tray, and latch the rear load floor cover.
Page 493: Road Tire Installation
WHAT TO DO IN EMERGENCIES 491 Road Tire Installation 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased 1. Mount the road tire on the axle. leverage. Tighten the lug nuts in a star pattern until 2.
Page 494: Jump-Starting
492 WHAT TO DO IN EMERGENCIES JUMP-STARTING WARNING! If your vehicle has a discharged battery it can be jump- Do not attempt jump-starting if the battery is frozen. started using a set of jumper cables and a battery in It could rupture or explode and cause personal injury. another vehicle or by using a portable battery booster pack.
Page 495 WHAT TO DO IN EMERGENCIES 493 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
Page 496: Jump-Starting Procedure
494 WHAT TO DO IN EMERGENCIES 1. Set the parking brake, shift the automatic transmission Jump-Starting Procedure into PARK and turn the ignition to LOCK. WARNING! 2. Turn off the heater, radio, and all unnecessary electri- cal accessories. Failure to follow this procedure could result in per- sonal injury or property damage due to battery ex- 3.
Page 497 WHAT TO DO IN EMERGENCIES 495 1. Connect the positive (+) end of the jumper cable to the 5. Start the engine in the vehicle that has the booster remote positive (+) post of the discharged vehicle. battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery.
Page 498: Freeing A Stuck Vehicle
496 WHAT TO DO IN EMERGENCIES If frequent jump-starting is required to start your vehicle FREEING A STUCK VEHICLE you should have the battery and charging system tested If your vehicle becomes stuck in mud, sand or snow, it at your authorized dealer. can often be moved using a rocking motion.
Page 499 WHAT TO DO IN EMERGENCIES 497 NOTE: Press the ESC Off switch (if necessary), to place CAUTION! the Electronic Stability Control (ESC) system in Partial • When “rocking” a stuck vehicle by shifting be- Off mode, before rocking the vehicle. Refer to “Elec- tronic Brake Control”...
Page 500: Emergency Tow Hooks - If Equipped
498 WHAT TO DO IN EMERGENCIES WARNING! (Continued) WARNING! explode and injure someone. Do not spin your vehi- • Do not use a chain for freeing a stuck vehicle. cle’s wheels faster than 30 mph (48 km/h) or for Chains may break, causing serious injury or death. longer than 30 seconds continuously without stop- •...
Page 501: Manual Park Release- 8 Speed Transmission
WHAT TO DO IN EMERGENCIES 499 MANUAL PARK RELEASE– 8 SPEED Follow these steps to use the Manual Park Release: TRANSMISSION 1. Open the center console and locate the Manual Park Release cover, remove it by snapping the cover away WARNING! from the console hinges.
Page 502 500 WHAT TO DO IN EMERGENCIES 2. Using a screwdriver or similar tool, push the metal 3. While the metal latch is the open position, simultane- latch in towards the tether strap. ously pull upwards on the tether strap until it clicks and releases out of the park position.
Page 503 WHAT TO DO IN EMERGENCIES 501 To Disengage the Manual Park Release Lever: 2. Once the tension has been released and the lever has been unlocked be sure it is stowed properly and locks 1. To disengage the Manual Park Release apply tension into position.
Page 504: Towing A Disabled Vehicle
502 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE leveling disabled, before tying them down (from the body) on a trailer or flatbed truck. Refer to the section on This section describes procedures for towing a disabled Quadra-Lift™ for more information. If the vehicle cannot be vehicle using a commercial wrecker service.
Page 505 WHAT TO DO IN EMERGENCIES 503 Proper towing or lifting equipment is required to prevent If the key fob is unavailable, or the vehicle’s battery is damage to your vehicle. Use only tow bars and other discharged, refer to “Manual Park Release” in “What to equipment designed for this purpose, following equip- Do in Emergencies”...
Page 506: Two-Wheel Drive Models
504 WHAT TO DO IN EMERGENCIES Two-Wheel Drive Models If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than The manufacturer recommends towing your vehicle with 30 miles (48 km), tow with the rear wheels OFF the all four wheels OFF the ground using a flatbed.
Page 507: Four-Wheel Drive Models
WHAT TO DO IN EMERGENCIES 505 Four-Wheel Drive Models Vehicles equipped with a single-speed transfer case have no NEUTRAL position, and therefore must be towed The manufacturer recommends towing with all wheels with all four wheels OFF the ground. OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and CAUTION! the opposite end on a towing dolly.
Page 509: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ENGINE COMPARTMENT — 3.6L ..509 Engine Air Cleaner Filter ....518 ENGINE COMPARTMENT — 5.7L ..510 Maintenance-Free Battery .
Page 510 508 MAINTAINING YOUR VEHICLE Transfer Case ......538 Front Turn Signal .....558 Automatic Transmission .
Page 511: Engine Compartment - 3.6L
MAINTAINING YOUR VEHICLE 509 ENGINE COMPARTMENT — 3.6L 1 — Power Distribution Center (Fuses) 6 — Air Cleaner Filter 2 — Engine Oil Dipstick 7 — Washer Fluid Reservoir 3 — Engine Oil Fill 8 — Coolant Pressure Cap (Radiator) 4 —...
Page 512: Engine Compartment - 5.7L
510 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Power Distribution Center 5 — Washer Fluid Reservoir 2 — Engine Oil Fill 6 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 7 — Coolant Pressure Cap (Radiator) 4 — Air Cleaner Filter 8 —...
Page 513: Onboard Diagnostic System (Obd Ii)
MAINTAINING YOUR VEHICLE 511 ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and drivability.
Page 514 512 MAINTAINING YOUR VEHICLE For states that require an Inspection and Mainte- 3. As soon as you turn the ignition switch to the ON nance (I/M), this check verifies the “Malfunction position, you will see the MIL symbol come on as part Indicator Light (MIL)”...
Page 515: Replacement Parts
MAINTAINING YOUR VEHICLE 513 you may need to do nothing more than drive your DEALER SERVICE vehicle as you normally would in order for your OBD II Your authorized dealer has the qualified service person- system to update. A recheck with the above test routine nel, special tools, and equipment to perform all service may then indicate that the system is now ready.
Page 516: Maintenance Procedures
514 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance • Your vehicle has been built with improved fluids services determined by the engineers who designed your that protect the performance and durability of your vehicle.
Page 517 MAINTAINING YOUR VEHICLE 515 check the engine oil level is about five minutes after a Change Engine Oil fully warmed engine is shut off, or before starting the The oil change indicator system will remind you that it is engine after it has sat overnight. time to take your vehicle in for scheduled maintenance.
Page 518 516 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Engine Oil Viscosity – 3.6L Engine Identification Symbol SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature This symbol means that the oil has starting and vehicle fuel economy.
Page 519 MAINTAINING YOUR VEHICLE 517 The engine oil filler cap also shows the recommended Materials Added To Engine Oil engine oil viscosity for your engine. For information on The manufacturer strongly recommends against the addi- engine oil filler cap location, refer to “Engine Com- tion of any additives (other than leak detection dyes) to the partment”...
Page 520: Engine Oil Filter
518 MAINTAINING YOUR VEHICLE Engine Oil Filter WARNING! The engine oil filter should be replaced with a new filter The air induction system (air cleaner, hoses, etc.) can at every engine oil change. provide a measure of protection in the case of engine Engine Oil Filter Selection backfire.
Page 521: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 519 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
Page 522: Air Conditioner Maintenance
520 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer battery that the positive cable is attached to the at the start of each warm season.
Page 523 MAINTAINING YOUR VEHICLE 521 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental approved by the manufacturer for your air condi- Protection Agency and is an ozone-saving product. How- tioning system.
Page 524 522 MAINTAINING YOUR VEHICLE A/C Air Filter Refer to the “Maintenance Schedule” for the proper maintenance intervals. WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box.
Page 525: Body Lubrication
MAINTAINING YOUR VEHICLE 523 attention should also be given to hood latching compo- CAUTION! nents to ensure proper function. When performing other underhood services, the hood latch, release mechanism The A/C air filter is identified with an arrow to and safety catch should be cleaned and lubricated. indicate airflow direction through the filter.
Page 526 524 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use.
Page 527: Adding Washer Fluid
MAINTAINING YOUR VEHICLE 525 3. Grab the bottom of the wiper blade and rotate it 4. Install the wiper blade pivot pin into the wiper blade forward to unsnap the blade pivot pin from the wiper holder at the end of the wiper arm, and firmly press blade holder.
Page 528: Exhaust System
526 MAINTAINING YOUR VEHICLE When refilling the washer fluid reservoir, take some Exhaust System washer fluid and apply it to a cloth or towel and wipe The best protection against carbon monoxide entry into clean the wiper blades, this will help blade performance. the vehicle body is a properly maintained engine exhaust To prevent freeze-up of your windshield washer system system.
Page 529 MAINTAINING YOUR VEHICLE 527 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 530 528 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is age: important to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 531: Cooling System
MAINTAINING YOUR VEHICLE 529 Cooling System authorized dealer. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by WARNING! gently spraying water from a garden hose vertically down the face of the condenser. You or others can be badly burned by hot engine Check the engine cooling system hoses for brittle rubber, coolant (antifreeze) or steam from your radiator.
Page 532 530 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, And Refill CAUTION! (Continued) If the engine coolant (antifreeze) is dirty or contains Organic Additive Technology (OAT) engine cool- visible sediment, clean and flush with OAT coolant ant is different and should not be mixed with (antifreeze) that meets the requirements of Chrysler Hybrid Organic Additive Technology (HOAT) en- Material Standard MS-12106.
Page 533 MAINTAINING YOUR VEHICLE 531 Please review these recommendations for using Organic CAUTION! (Continued) Additive Technology (OAT) engine coolant (antifreeze) • This vehicle has not been designed for use with that meets the requirements of Chrysler Material Stan- propylene glycol-based engine coolant (antifreeze). dard MS-12106.
Page 534 532 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to main- The cap should be inspected and cleaned if there is any tain the proper level of protection against freezing ac- accumulation of foreign material on the sealing surfaces. cording to the temperatures occurring in the area where the vehicle is operated.
Page 535 MAINTAINING YOUR VEHICLE 533 Disposal Of Used Engine Coolant The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for Used ethylene glycol-based engine coolant (antifreeze) is engine coolant (antifreeze) freeze point or replacing cool- a regulated substance requiring proper disposal.
Page 536 534 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are Points To Remember required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming •...
Page 537: Brake System
MAINTAINING YOUR VEHICLE 535 Brake System Fluid Level Check – Brake Master Cylinder In order to assure brake system performance, all brake The fluid level of the master cylinder should be checked system components should be inspected periodically. when performing under the hood service, or immedi- Refer to the “Maintenance Schedule”...
Page 538 536 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) fluid in a open container absorbs moisture from • Use only manufacturer’s recommended brake the air resulting in a lower boiling point. This may fluid. Refer to “Fluids, Lubricants, and Genuine cause it to boil unexpectedly during hard or pro- Parts”...
Page 539: Front/Rear Axle Fluid
MAINTAINING YOUR VEHICLE 537 Front/Rear Axle Fluid Rear Axle Fluid Level Check For normal service, periodic fluid level checks are not The rear axle oil level needs to be between 1/8 in (3 mm) required. When the vehicle is serviced for other reasons the below the bottom of the fill hole and the bottom of the fill exterior surfaces of the axle assembly should be inspected.
Page 540: Transfer Case
538 MAINTAINING YOUR VEHICLE Transfer Case CAUTION! Fluid Level Check When installing plugs, do not overtighten. You could For normal service, periodic fluid level checks are not damage them and cause them to leak. required. When the vehicle is serviced for other reasons Selection Of Lubricant the exterior surfaces of the transfer case assembly should be inspected.
Page 541 MAINTAINING YOUR VEHICLE 539 “Maintaining Your Vehicle” for fluid specifications. It is Special Additives important to maintain the transmission fluid at the The manufacturer strongly recommends against using correct level using the recommended fluid. any special additives in the transmission. NOTE: No chemical flushes should be used in any Automatic Transmission Fluid (ATF) is an engineered transmission;...
Page 542 540 MAINTAINING YOUR VEHICLE Fluid Level Check CAUTION! The fluid level is preset at the factory and does not • If a transmission fluid leak occurs, visit your au- require adjustment under normal operating conditions. thorized dealer immediately. Severe transmission Routine fluid level checks are not required, therefore the damage may occur.
Page 543: Appearance Care And Protection From Corrosion
MAINTAINING YOUR VEHICLE 541 Appearance Care And Protection From Corrosion What Causes Corrosion? Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 544 542 MAINTAINING YOUR VEHICLE Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- • Do not use abrasive or strong cleaning materials hicle in the shade using MOPAR® Car Wash, or a mild such as steel wool or scouring powder that will car wash soap, and rinse the panels completely with scratch metal and painted surfaces.
Page 545 MAINTAINING YOUR VEHICLE 543 • If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care touch them up immediately. The cost of such repairs is • All wheels and wheel trim, especially aluminum and considered the responsibility of the owner.
Page 546 544 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure – Interior Care If Equipped Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following manner: carpeting. • Remove as much of the stain as possible by blotting Use MOPAR®...
Page 547 MAINTAINING YOUR VEHICLE 545 Do not use abrasive cleaning components, solvents, steel WARNING! wool or other aggressive material to clean the lenses. Do not use volatile solvents for cleaning purposes. Glass Surfaces Many are potentially flammable, and if used in All glass surfaces should be cleaned on a regular basis closed areas they may cause respiratory harm.
Page 548: Fuses
546 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses If the belts need cleaning, use MOPAR® Total Clean, a mild soap solution, or lukewarm water. Do not remove The lenses in front of the instruments in this vehicle are the belts from the vehicle to wash them. Dry with a soft molded in clear plastic.
Page 549 MAINTAINING YOUR VEHICLE 547 Cavity Car- Micro Description tridge Fuse Fuse 40 Amp Compressor for Green Air Suspension if equipped 40 Amp Antilock Brakes/ Green Electronic Stability Control Pump 40 Amp Starter Solenoid Green Power Distribution Center 40 Amp Emission sensors Green (Diesel engine only) Cavity...
Page 550 548 MAINTAINING YOUR VEHICLE Cavity Car- Micro Description Cavity Car- Micro Description tridge Fuse tridge Fuse Fuse Fuse 30 Amp Trailer Tow Electric 30 Amp Body Controller #1 Pink Brake - If Equipped Pink 40 Amp Body Controller #3 30 Amp Driver Door Green / Interior Lights...
Page 551 MAINTAINING YOUR VEHICLE 549 Cavity Car- Micro Description Cavity Car- Micro Description tridge Fuse tridge Fuse Fuse Fuse 20 Amp Trailer Tow 30 Amp Rear Blower - Yellow Parking Lights - Pink If Equipped If Equipped 30 Amp Power Inverter 30 Amp Trailer Tow Recep- Pink...
Page 552 550 MAINTAINING YOUR VEHICLE Cavity Car- Micro Description Cavity Car- Micro Description tridge Fuse tridge Fuse Fuse Fuse 10 Amp Tire Pressure 20 Amp Trailer Tow – Left Monitor Yellow Turn/Stop Lights - If Equipped 10 Amp Integrated Central Stack / Climate 15 Amp Additional Content Control...
Page 553 MAINTAINING YOUR VEHICLE 551 Cavity Car- Micro Description Cavity Car- Micro Description tridge Fuse tridge Fuse Fuse Fuse 20 Amp Ignition Coils 20 Amp Fuel Pump Motor Yellow (Gas), Urea Heater Yellow (Diesel) 30 Amp Audio Amplifier 25 Amp Fuel Injectors / Green Natural Powertrain...
Page 554 552 MAINTAINING YOUR VEHICLE Cavity Car- Micro Description Cavity Car- Micro Description tridge Fuse tridge Fuse Fuse Fuse 10 Amp Drivetrain Control 10 Amp Steering Column Module/Front Axle Control Module/ Disconnect Module Cruise Control 10 Amp Engine Control 10 Amp Fuel Door Module / Electric Power Steering -...
Page 555 MAINTAINING YOUR VEHICLE 553 Cavity Car- Micro Description Cavity Car- Micro Description tridge Fuse tridge Fuse Fuse Fuse 10 Amp Air Suspension / 10 Amp Rear Camera / Trailer Tow / Park Assist Steering Column 10 Amp Rear Seat Heater Control Module Switch / Flashlamp 15 Amp...
Page 556 554 MAINTAINING YOUR VEHICLE Cavity Car- Micro Description CAUTION! tridge Fuse • When installing the power distribution center Fuse cover, it is important to ensure the cover is properly F100 10 Amp Active Damping - positioned and fully latched. Failure to do so may If Equipped allow water to get into the power distribution F101...
Page 557: Vehicle Storage
MAINTAINING YOUR VEHICLE 555 VEHICLE STORAGE REPLACEMENT BULBS If you are leaving your vehicle dormant for more than Interior Bulbs 21 days you may want to take steps to protect your battery. You may: Bulb Number • Disconnect the negative cable from the battery. Glove Box Lamp Grab Handle Lamp L002825W5W...
Page 558 556 MAINTAINING YOUR VEHICLE Exterior Bulbs Bulb Number Bulb Number Auxiliary Liftgate Tail Lamps LED - (Service at Headlamps (Low Beam) Authorized Dealer) Premium Headlamps D3S (Serviced at Liftgate Backup Lamps 921 (W16W) (Low/High Beam) Authorized Dealer) Rear License Lamps LED - (Service at Headlamps (High Beam) 9005...
Page 559: Bulb Replacement
MAINTAINING YOUR VEHICLE 557 BULB REPLACEMENT NOTE: On vehicles equipped with High Intensity Dis- charge (HID) headlamps , when the headlamps are turned High Intensity Discharge Headlamps (HID) – on, there is a blue hue to the lamps. This diminishes and If Equipped becomes more white after approximately 10 seconds, as the The headlamps are a type of high voltage discharge tube.
Page 560: Front Turn Signal
558 MAINTAINING YOUR VEHICLE Front Turn Signal Front Fog Lamps 1. Open the hood. 1. Reach through the cutout in the splash shield and disconnect the wiring harness from the fog lamp 2. Turn the turn signal bulb one–quarter turn counter- connector.
Page 561: Rear Tail, Stop, And Turn Signal Lamps
MAINTAINING YOUR VEHICLE 559 Rear Tail, Stop, and Turn Signal Lamps CAUTION! (Continued) 1. Raise the liftgate. • Always use the correct bulb size and type for replacement. An incorrect bulb size or type may 2. Remove the two push-pins from the tail lamp housing. overheat and cause damage to the lamp, the socket 3.
Page 562: Rear Liftgate Mounted Tail Lamp
560 MAINTAINING YOUR VEHICLE 4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to remove it from the socket. 6. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Rear Liftgate Mounted Tail Lamp 1.
Page 563 MAINTAINING YOUR VEHICLE 561 Rear Liftgate Tail Lamps 1 — Auxiliary LED Tail Connector – Do Not Remove 5. Tail lamps are now visible. Rotate socket(s) counter 2 — Backup Bulb Socket clockwise. 6. Remove/replace bulb(s). 7. Reinstall the socket(s) 8.
Page 564: Center High-Mounted Stop Lamp (Chmsl)
562 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Lamp (CHMSL) Rear License Lamp The center high mounted stop lamp is LED. Service at The rear license lamps are LED. Service at Authorized Authorized Dealer. Dealer. Center High-Mounted Stop Lamp...
Page 565: Fluid Capacities
MAINTAINING YOUR VEHICLE 563 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 3.6L and 5.7L Engines 25 Gallons 94 Liters Engine Oil With Filter 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters 5.7L Engine (SAE 5W-20, API Certified) 7 Quarts 6.6 Liters Cooling System* 3.6L Engine (MOPAR®...
Page 566: Fluids, Lubricants And Genuine Parts
564 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). Engine Oil – 3.6L Engine We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 567: Chassis
MAINTAINING YOUR VEHICLE 565 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission We recommend you only use Mopar® ZF 8&9 Speed ATF™ Automatic Trans- mission Fluid or Shell L12108 Transmission Fluid. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer Case –...
Page 568 566 MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Brake Master Cylinder We recommend you use MOPAR® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Power Steering Reservoir –...
Page 569: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS MAINTENANCE SCHEDULE ... . .568 Maintenance Chart.....570...
Page 570 568 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a Your vehicle is equipped with an automatic oil change scheduled oil change is performed by someone other indicator system.
Page 571 MAINTENANCE SCHEDULES 569 Once A Month Or Before A Long Trip: At Every Oil Change Interval As Indicated By • Check engine oil level Oil Change Indicator System: • Change oil and filter. • Check windshield washer fluid level • Rotate the tires. Rotate at the first sign of irregu- •...
Page 572 570 MAINTENANCE SCHEDULES Maintenance Chart Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 573 MAINTENANCE SCHEDULES 571 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Inspect the brake linings, parking brake function. Inspect transfer case fluid. Additional Maintenance Replace engine air filter. Replace the air conditioning filter. Replace spark plugs (3.6L engine).** Replace spark plugs (5.7L engine).**...
Page 574 572 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change transfer case fluid. Inspect and replace PCV valve if necessary.
Page 575 MAINTENANCE SCHEDULES 573 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 577: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE Customer Assistance For The Hearing Or Speech FOR YOUR VEHICLE ....577 Impaired (TDD/TTY)....579 Prepare For The Appointment.
Page 578 576 IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION Traction Grades ..... . .583 UNIFORM TIRE QUALITY GRADES ..583 Temperature Grades.
Page 579: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 577 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 580: Chrysler Group Llc Customer Center
578 IF YOU NEED CONSUMER ASSISTANCE • Authorized dealer name service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and • Vehicle Identification Number (VIN) the latest information to ensure the vehicle is fixed • Vehicle delivery date and mileage correctly and in a timely manner.
Page 581: In Mexico Contact
IF YOU NEED CONSUMER ASSISTANCE 579 In Mexico contact: Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered Av. Prolongacion Paseo de la Reforma, 1240 by Bell Canada. For TTY teletypewriter users, dial 711 Sante Fe C.P.
Page 582: Warranty Information
580 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service WARNING! contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than Engine exhaust, some of its constituents, and certain the manufacturer’s service contract.
Page 583: Mopar® Parts
IF YOU NEED CONSUMER ASSISTANCE 581 MOPAR® PARTS To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), MOPAR® fluids, lubricants, parts, and accessories are or go to http://www.safercar.gov; or write to: Administra- available from an authorized dealer.
Page 584: Publication Order Forms
582 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS Diagnostic Procedure Manuals To order the following manuals, you may use either the Diagnostic Procedure Manuals are filled with diagrams, website or the phone numbers listed below. Visa, Master- charts and detailed illustrations. These practical manuals card, American Express, and Discover orders are accepted.
Page 585 IF YOU NEED CONSUMER ASSISTANCE 583 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled • 1–800–387–1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 586 584 IF YOU NEED CONSUMER ASSISTANCE The grade C corresponds to a level of performance, WARNING! which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A The traction grade assigned to this tire is based on represent higher levels of performance on the laboratory straight-ahead braking traction tests, and does not test wheel, than the minimum required by law.
Page 587 INDEX...
Page 588 586 INDEX Adaptive Cruise Control (ACC) (Cruise Control) . . .188 Alarm (Security Alarm) ..... .20 Adding Engine Coolant (Antifreeze) ... .531 Alterations/Modifications, Vehicle .
Page 589 INDEX 587 Special Additives ..... . .539 Brake/Transmission Interlock ....359 Auxiliary Electrical Outlet (Power Outlet) .
Page 590 588 INDEX Center High Mounted Stop Light ....562 Cooling System......529 Certification Label.
Page 591 INDEX 589 Defroster, Rear Window.....278 Electronic Brake Control System ....397 Defroster, Windshield .
Page 592 590 INDEX Exhaust Gas Caution .....48 Exhaust System......110 Fails to Start .
Page 593 INDEX 591 Fluid Capacities ......563 Fuel ........442 Fluid Leaks .
Page 594 592 INDEX Gasoline (Fuel) ......442 Passing ......174 Gasoline, Reformulated .
Page 595 INDEX 593 Instrument Panel and Controls ....283 Keys ........14 Instrument Panel Lens Cleaning .
Page 596 594 INDEX Brake Warning ......289 Rear Tail ......559 Bulb Replacement .
Page 597 INDEX 595 Maintenance Free Battery....519 Mopar Parts ......513 Maintenance Procedures .
Page 598 596 INDEX Filter Disposal ......517 Park Sense System, Rear ....218 Identification Logo .
Page 599 INDEX 597 Pretensioners Rear Wiper/Washer......277 Seat Belts ......61 Reclining Front Seats .
Page 600 598 INDEX Restraints, Child ......83 Extender ......67 Restraints, Occupant .
Page 601 INDEX 599 Sentry Key Replacement .....19 Engine Block Heater .....356 Service Assistance .
Page 602 600 INDEX Suspension, Air......378 High Speed ......425 Sway Control, Trailer.
Page 603 INDEX 601 Tongue Weight/Trailer Weight ....462 Transmission ......360 Tow Hooks, Emergency .
Page 604 602 INDEX Vehicle Loading ......418 Windshield Defroster ..... . .111 Vehicle Modifications/Alterations .
Page 605 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use only frequency signals.
Page 606 Chrysler Group LLC Chrysler Group LLC Chrysler Group LLC 14WK741-126-AB 14WK741-126-AA 14WK741-126-AA 14WK741-126-AA Second Edition Second Edition Second Edition Third Edition Printed in U.S.A. Printed in U.S.A. Printed in U.S.A. Printed in U.S.A.

This manual is also suitable for:

2014 grand cherokee 2011 grand cherokee

Jeep Grand Cherokee Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Grand Cherokee

Summary of Contents for Jeep Grand Cherokee