Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....6 Roll Over Warning .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION handles on different road surfaces. Your driving skills Thank you for selecting a Jeep Grand Cherokee and will improve with experience. When driving off-road or welcome to our worldwide family. working the vehicle, don’t overload it or expect it to overcome the laws of nature.
Page 5 INTRODUCTION 5 Do not attempt sharp turns or abrupt maneuvers or other Failure to use driver and passenger seat belts provided unsafe driving actions that can cause loss of vehicle is a major cause of severe or fatal injury. In fact, the U.S. control.
Page 6: Warnings And Cautions
6 INTRODUCTION NOTE: After you read the manual, it should be stored HOW TO USE THIS MANUAL in the vehicle for convenient reference and remain with Consult the table of contents to determine which section the vehicle when sold so that the new owner will be contains the information you desire.
Page 7: Vehicle Identification Number
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle.
Page 8: Vehicle Modifications / Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Doors And Door Locks ....15 Ignition Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service ....21 Energy Management Feature ....33 Security Alarm System —...
Page 11: Things To Know Before Starting Your Vehicle 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number.
Page 12: Key-In-Ignition Reminder
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder keys that have been programmed to the vehicle can be If the driver’s door is opened when the key is in the used to start and operate the vehicle for longer than the ignition and not turned to the ON position, a chime will 2 second validation time period.
Page 13: Important Note About Service
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 If the SKIS indicator light comes on during normal Important Note About Service vehicle operation (it has been running for longer than 10 A four digit PIN number is needed to service the Sentry seconds) a fault has been detected in the electronics and Key Immobilizer System.
Page 14: Customer Key Programming
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle will sound and the SKIS indicator light will begin to electronics. A blank key is one which has never been flash. Turn the ignition switch OFF and remove the programmed.
Page 15: Illuminated Entry
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 ILLUMINATED ENTRY WARNING! The interior lights come on when you open any door. They will remain on for about 30 seconds after all doors For personal security, and safety in the event of an are closed then fade to off.
Page 16 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! CAUTION! Avoid trapping anyone in the vehicle in a collision. An unlocked vehicle is an invitation to thieves. Remember that the rear doors can only be opened Always remove the key from the ignition and lock from the outside when the child protection locks are all of the doors when leaving the vehicle unattended.
Page 17: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 If you press the door lock switch while the keys are in the Power Door Locks A door lock switch is on each front door panel. Press this ignition switch, and the driver’s door is open, the doors switch to lock or unlock the doors.
Page 18: Remote Keyless Entry
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock on Exit Feature — Only Available if Auto Lock is Enabled This feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in P (Park) or N (Neutral).
Page 19: To Lock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: If desired, the system can be programmed to Customer Programmable Features of the “Electronic Ve- unlock all doors on the first press of the “Unlock” button. hicle Information Center (EVIC)” section or by following Refer to “Remote Unlock Driver’s Door 1st”...
Page 20: General Information
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The panic alarm will stay on for 3 minutes unless you 1. Press the LOCK button for 4 to 10 seconds. turn it off by pressing the PANIC button a second time or 2.
Page 21: Transmitter Battery Service
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is one CR2032 battery.
Page 22: Security Alarm System - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case, snap the two liftgate will cancel the arming. If the system successfully halves together. Make sure there is an even “gap” be- arms, the red light will flash at a slower rate to indicate tween the two halves.
Page 23: Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 press the “Unlock” button on the remote keyless entry transmitter to disarm the system. The Security Alarm System will not disarm with a manual unlock, either through the lock plunger located on the inside of the door, or through a key in the driver’s door key cylinder.
Page 24: Liftgate Flipper Glass
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked.
Page 25: Power Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Once the liftgate flipper glass has been opened, connec- POWER WINDOWS tion to the rear window wiper is interrupted, preventing The power window controls are located on the driver’s activation of the rear wiper blade while the flipper glass door trim panel.
Page 26: Auto Down
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power window switches remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Auto Down The driver’s window switch has an “Auto Down” fea- ture.
Page 27: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 open or partially open positions. This is a normal occur- Please pay close attention to the information in this rence and can be minimized. If the buffeting occurs with section. It tells you how to use your restraint system the sunroof open, adjust the sunroof opening to minimize properly to keep you and your passengers as safe as the buffeting.
Page 28: Lap/Shoulder Belts
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they WARNING! can reduce the seriousness of injuries in a collision. Some • Wearing a seat belt incorrectly is dangerous. Seat of the worst injuries happen when people are thrown from the vehicle.
Page 29: Lap/Shoulder Belt Operating Instructions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” A belt that is buckled into the wrong buckle will not protect you properly.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 4. Position the lap belt across your thighs, below your 5. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap portion, pull up a comfortable and not resting on your neck.
Page 32: Adjustable Upper Shoulder Belt Anchorage
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button marked PRESS Adjustable Upper Shoulder Belt Anchorage on the buckle. The belt will automatically retract to its In the front seating positions, the shoulder belt can be stowed position.
Page 33: Automatic Locking Mode - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 As a guide, if you are shorter than average, you will 3. Allow the belt to retract. As the belt retracts, you will prefer a lower position, and if you are taller than average, hear a clicking sound.
Page 34: Seat Belt Pretensioners
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat WARNING! belt placement by the occupant. The seat belt must still be • The belt and retractor assembly must be replaced worn snugly and positioned properly. if the seat belt assembly “automatic locking re- The pretensioners are triggered by the Occupant Re- tractor”...
Page 35: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 seconds or until the driver’s seat belt is buckled. The 3. Within 60 seconds of starting the vehicle, unbuckle Enhanced Warning System (BeltAlert) will be reactivated and then re-buckle the driver’s seat belt at least three if the driver’s seat belt is unbuckled for more than 10 times, ending with the seat belt buckled.
Page 36: Seat Belt Extender
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pregnant women should wear the lap part of the belt WARNING! across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the Using a seat belt extender when not needed can abdomen.
Page 37: Driver And Front Passenger Supplemental Restraint Systems (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 This vehicle has airbags for both the driver and right Driver And Front Passenger Supplemental Restraint Systems (SRS) front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle may also be equipped with window bags to WARNING! protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with window • Do not put anything on or around the front airbag bags, they are located above the side windows.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 The front airbags have a multi stage inflator design. This severe side collisions. In certain types of collisions, both allows the airbag to have different rates of inflation that the front and side airbags may be triggered. But even in are based on collision severity.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE children who do not use child restraints or belt- 3. The driver and front passenger seats should be moved positioning booster seats should ride properly buckled back as far as practical to allow the front airbags room to up in the rear seat.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Airbag System Components WARNING! The airbag system consists of the following: • Relying on the airbags alone could lead to more • Occupant Restraint Control Module severe injuries in a collision. The airbags work •...
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Acceleration Sensors occupant size provided by the Occupant Classification Module. The ORC will not detect roll over, or rear • Driver and Front Passenger Seat Belt Pretensioner impacts. • Occupant Classification System (OCS) — Front Pas- The ORC also monitors the readiness of the electronic senger Seat Only parts of the system whenever the ignition switch is in...
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • The Occupant Classification System (OCS) is part of section). If the ORC detects a malfunction in any part of the system, it turns on the “Airbag Warning Light” a Federally regulated safety system required for this either momentarily or continuously.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE objects are placed on the seat, the passenger airbag properly wear the vehicle’s seat belt, and when an will not inflate even though the “PAD Indicator Light” adult passenger is properly seated in the front passen- is not illuminated.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 adult. An adult occupant needs to sit in a normal position Passenger Airbag Front Passenger Airbag (with their feet on or near the floor) in order to be Disable (PAD) Seat Occupant Status properly classified.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the front passenger seat is damaged in any way, it Light.” Once the lodged object is removed, the fault will should only be serviced by an authorized dealer. If the be automatically cleared after a short period of time. seat is removed (or even if the seat attachment bolts are •...
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 airbag gas is vented through the vent holes in the sides the ORC (with side impact option) detects a collision of the airbag. In this way, the airbags do not interfere requiring the side curtain airbag to inflate, it signals with your control of the vehicle.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not use prior or future model year seat covers not The front passenger seat assembly contains critical com- ponents that affect the front passenger airbag deploy- designated for the specific model being repaired. Al- ment.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: A frontal collision that is not severe enough to WARNING! need airbag protection will not activate the system. This does not mean something is wrong with the airbag Unapproved modifications or service procedures to system.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate you may see some smoke-like WARNING! particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag Deployed airbags and seat belt pretensioners cannot inflation.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Airbag System Airbag Warning Light You will want to have the airbag system ready to inflate WARNING! for your protection in an impact. The airbag system is • designed to be maintenance free. If any of the following Modifications to any part of the airbag system could cause it to fail when you need it.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE data gathered during a complete accident investigation, provided to the custodial entity upon request. General the electronic data may be used by DaimlerChrysler data that does not identify particular vehicles or crashes Corporation and others to learn more about the possible may be released for incorporation in aggregate crash causes of crashes and associated injuries in order to...
Page 53: Child Restraint
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Data Parameters that May Be Recorded: Child Restraint Everyone in your vehicle needs to be buckled up all the • Diagnostic trouble code(s) and warning lamp status time — babies and children, too. Every state in the United for electronically-controlled safety systems, including States and all Canadian provinces require that small the airbag system...
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats often In a collision, an unrestrained child, even a tiny have a higher weight limit in the rearward-facing baby, can become a missile inside the vehicle.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Standards. The manufacturer also recommends that WARNING! you try a child restraint in the vehicle seats where you • Improper installation can lead to failure of an will use it before you buy it. infant or child restraint.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still cannot be tightened, or if pulling and cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the pushing on the restraint loosens the belt, disconnect belt occasionally and pull it tight if necessary).
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Older Children and Child Restraints Children Too Large for Booster Seats Children who weigh more than 20 lbs (9 kg) and who are Children who are large enough to wear the shoulder belt older than one year can ride forward-facing in the comfortably, and whose legs are long enough to bend vehicle.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower kits or retro-fit kits. You are urged to take advantage of all Anchors and Tether for CH ildren) the available attachments provided with your child re- Your vehicle’s rear seat is equipped with the child straint in any vehicle.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each means of adjusting the tension in the strap. Forward- rear seating position located on the back of the seat. facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 If the seat belt has a automatic locking retractor, it will WARNING! have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the Improper installation of a child restraint to the child restraint and slide the latch plate into the buckle.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: Route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat.
Page 63: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your new vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 64: Safety Tips
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not inhale exhaust gases. They contain carbon A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be monoxide, a colorless and odorless gas which can kill. considered as a normal part of the break-in and not Never run the engine in a closed area, such as a interpreted as an indication of difficulty.
Page 65: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Safety Checks You Should Make Inside The Defrosters Vehicle Check operation by selecting the defrost mode and place the blower control on high speed. You should feel the air Seat Belts directed against the windshield. Inspect the belt system periodically, checking for cuts, frays and loose parts.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check area under vehicle after overnight parking for fuel, coolant, oil or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected immediately.
Page 67: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......72 Hands–Free Communication (UConnect™) — If Equipped .
Page 68 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline ..100 Lights ....... 111 Manual Lumbar Support Adjustment .
Page 69 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Turn Signals ......116 Rear Park Assist Sensors ....128 High Beam Switch .
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driving Up Or Down Hills ....136 Closing Sunroof - Express ....146 Overhead Console —...
Page 71 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 Rear Storage Compartment ....151 Rear Window Features ....155 Retractable Cargo Area Cover —...
Page 72: Mirrors
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted while set in the day position (toward windshield).
Page 73: Inside Automatic Dimming Mirror - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Inside Automatic Dimming Mirror — If Equipped CAUTION! This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature To avoid damage to the mirror during cleaning, on or off by pressing the button at the base of the mirror.
Page 74: Exterior Mirrors Folding Feature
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exterior Mirrors Folding Feature WARNING! All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have Vehicles and other objects seen in the right side three detent positions;...
Page 75: Power Remote Control Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Power Remote Control Outside Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror, or off position. After selecting a mirror move the knob in the same direction you want the mirror to move.
Page 76: Lighted Vanity Mirrors - If Equipped
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lighted Vanity Mirrors — If Equipped HANDS–FREE COMMUNICATION (UConnect™) — To access a lighted vanity mirror, flip down one of the IF EQUIPPED visors. UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial Lift the cover to reveal the mirror.
Page 77 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 UConnect™ allows you to transfer calls between the with the system at a time. The system is available in system and your cellular phone as you enter or exit your English, Spanish, or French languages (as equipped). vehicle, and enables you to mute the system’s micro- The rearview mirror contains the microphone for the phone for private conversation.
Page 78: Operation
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any Hands- Operation Free Profile certified Bluetooth™ cellular phone. If your Voice commands can be used to operate the UConnect™ cellular phone supports a different profile (eg., Headset system and to navigate through the UConnect™...
Page 79 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 • For each of the feature explanation in this section, only To activate the UConnect™ system from idle, simply the combined form of the voice command is given. press the ’Phone’ button and follow audible prompts for You can also break the commands into parts and say directions.
Page 80 Before attempting to pair phone, please see • www.dodge.com/uconnect your cellular phone’s user manual (Bluetooth section) • www.jeep.com/uconnect for instructions on how to complete this step. • For identification purposes, you will be prompted to The following are general phone to UConnect™ System pairing instructions: give the UConnect™...
Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 phones are present in the vehicle, the UConnect™ 234-567-890 is nine digits long, which is not a valid system will use the priority 3 cellular phone when you phone number - the closest valid phone number has make a call.
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect™ phone- long names helps the voice recognition and is recom- book.
Page 83 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 four associated phone numbers and designations. Each After you are finished editing an entry in the phonebook, language has a separate 32 name phonebook accessible you will be given the opportunities to edit another entry only in that language.
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After confirmation, the phonebook entries will be Names to hear a list of the entries in the phonebook from which you choose. To select one of the entries deleted. from the list, press the Voice Recognition button List All Names in the UConnect™...
Page 85: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Phone Call Features Answer or Reject an Incoming Call - Call The following features can be accessed through the Currently in Progress UConnect™ system if the feature(s) are available on your If a call is currently in progress and you have another cellular service plan.
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE second call is in progress. To go back to the first call, refer Conference Call to section Toggling Between Two Calls. To combine two When two calls are in progress (one active and one on calls, refer to section Conference Call.
Page 87: Uconnect™ System Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 until the vehicle battery condition dictates cessation of Redial the call on the UConnect™ system and transfer of the • Press the ’Phone’ button to begin. call to the mobile phone. • After the Ready prompt and the following beep, say •...
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say If the phone is not reachable and the UConnect™ system the name of the language you wish to switch to is operational, you may reach the emergency number as (English, Espanol, or Francais, if so equipped).
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Your phone must be turned on and paired to the UCon- Paging nect™ system to allow use of this vehicle feature in To learn how to page, refer to section Working with emergency situations when the cell phone has network Automated Systems.
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system Turning Confirmation Prompts On/Off that normally requires you to enter in a touch-tone Turning confirmation prompts off will stop the system sequence on your cellular phone keypad, you can push from confirming your choices (e.g.
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • Press the ’Voice Recognition’ button. dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By • After the Ready prompt and the following beep, say dialing a number with your paired Bluetooth™...
Page 92: Advanced Phone Connectivity
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity List Paired Cellular Phone Names • Press the ’Phone’ button to begin. Transfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be • After the “Ready” prompt and the following beep, say transferred to your cellular phone to the UConnect™...
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • Press the ’Phone’ button to begin. Delete UConnect™ Paired Cellular Phones • After the Ready prompt and the following beep, say • Press the ’Phone’ button to begin. Setup Select Phone. • After the Ready prompt and the following beep, say •...
Page 94: Things You Should Know About Your Uconnect™ System
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Even though the system is designed for users speaking Things You Should Know About Your UConnect™ in North American English and Spanish accents, the System system may not always work for some. Voice Recognition (VR) •...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Far End Audio Performance Bluetooth Communication Link Cellular phones have been found to occasionally loose • Audio quality is maximized under: connection to the UConnect™ system. When this hap- • low-to-medium blower setting, pens, the connection can generally be re-established by switching the phone off/on.
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97...
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 99: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 SEATS North American English Primary Alternate(s) WARNING! Zero Add location Add new Adjusting a seat while the vehicle is moving is All of them dangerous. The sudden movement of the seat could Confirmation prompts Confirmations prompts cause you to lose control.
Page 100: Front Seat Adjustment - Recline
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline WARNING! To adjust the seatback, lift the lever located on the • It is extremely dangerous to ride in a cargo area, outboard side of the seat, lean back, and release the lever at the desired position.
Page 101: Manual Lumbar Support Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Manual Lumbar Support Adjustment Head Restraints The manual lumbar support adjustment lever is located Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head on the right side of the driver’s seat and on the left side restraints should be adjusted so that the upper edge is as of the passenger’s seat.
Page 102: Way Driver's Power Seat
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8 - Way Driver’s Power Seat 4 - Way Passenger’s Power Seat — If Equipped The driver’s power seat switches are located on the The front passenger’s power seat switches are located on outboard side of the driver’s seat lower side trim.
Page 103: 60/40 Split Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 indicate the level of heat in use. Two LEDs are illumi- When high-temperature heating is selected, the heaters nated for high, one for low, and none for off. Pressing the provide a boosted heat level during the first five minutes switch once will select high-level heating.
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Be sure that the front seats are fully upright and 2. Fold the rear seat completely forward. positioned forward. This will allow the rear seatback to fold down easily. 1. Pull the release strap (toward the front of the vehicle) to release.
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 proper position. The automatically folding rear head Storage — Rear Seat Armrest (If Equipped) restraints must be manually returned from the folded The rear seat may be equipped with a center storage position to the seating position. armrest.
Page 106: Driver Memory System - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the latch and lift the top of the armrest to access the DRIVER MEMORY SYSTEM — IF EQUIPPED storage bin. The storage bin has an integrated cargo net. Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
Page 107: Setting Memory Positions And Linking Remote
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Your vehicle may have been delivered with two Remote 3. Adjust the driver’s seat, recliner, and driver’s side Keyless Entry transmitters. One or both transmitters can view mirror to the desired positions. be linked to either memory position. The memory system 4.
Page 108: Memory Position Recall
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 9. Press and release the “Lock” button on one of the Memory Position Recall transmitters. NOTE: The vehicle must be in Park to recall memory 10. Insert the ignition key and turn the ignition switch to positions.
Page 109: To Disable A Transmitter Linked To Memory
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 mirror, and the pedals stop moving. A delay of one 4. Within 5 seconds, press and release memory button 1 second will occur before another recall can be selected. on the driver’s door. To Disable A Transmitter Linked to Memory 5.
Page 110: To Open And Close The Hood
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD Then reach under the hood and pull upward on the To open the hood, pull the release lever inside your safety latch and lift the hood. To prevent possible dam- vehicle located below the instrument panel and in front age, do not slam the hood to close it.
Page 111: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Front Map/Reading Lights WARNING! These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the If the hood is not fully latched, it could fly up when lens.
Page 112: Multi-Function Control Lever
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever Battery Saver Feature—Exterior/Interior Lights The multi-function control lever controls the operation of If the multi-function control lever is left in the interior the headlights, turn signals, headlight beam selection, light position, parking light position, or the headlight instrument panel light dimming, passing light, interior position when the ignition switch is moved to the OFF courtesy/dome lights, and optional fog lights.
Page 113: Headlights And Parking Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Headlights and Parking Lights Automatic Headlight System — If Equipped Turn the end of the multi-function control lever to the Turn the end of the multi-function control lever to the first detent for parking light operation. Turn to the third detent to activate the automatic headlight system.
Page 114: Smartbeams - If Equipped
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE approximately four minutes after the wipers completely To Activate stop. Refer to “Windshield Wipers and Washers” in this 1. Select “Enable Auto HI Beams.” Refer to “EVIC — section for more information Customer Programmable Features” in Section 4 of this NOTE: When your headlights come on during the manual.
Page 115: Instrument Panel And Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: Broken, muddy, or obstructed headlights and even when the doors and liftgate are open. While in the taillights of vehicles in the field of view will cause “Off” position the instrument panel lighting is at the headlights to remain on longer (closer to the vehicle).
Page 116: Fog Lights - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped Turn Signals The fog light switch is located in the multi- Move the multi-function control lever up or down and function control lever. To activate the fog lights, the arrows on each side of the instrument cluster will turn on the park/turn lights, low beam headlights, flash to show proper operation of the front and rear turn...
Page 117: Headlight Time Delay
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Headlight Time Delay There is also a feature that delays turning off the vehicle lights for 30, 60, or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multi- function control lever must be rotated to the “Off”...
Page 118: Mist
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold Mist while spray is desired. If the lever is pulled while in the Use this feature when weather conditions make occa- delay range, the wiper will operate for several seconds sional usage of the wipers necessary.
Page 119: Rain Sensing Wipers-If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 The sensitivity of the system can be adjusted with the Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and multi-function lever. Wiper delay position 1 is the least automatically activates the wipers for the driver. The sensitive, and wiper delay position 5 is the most sensi- feature is especially useful for road splash or overspray tive.
Page 120: Tilt Steering Column
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The rain sensing system will not operate under the TILT STEERING COLUMN following conditions: when the engine is running and To tilt the column, push down on the lever below the turn the gear selector is in the PARK position, or when the signal control and move the wheel up or down, as vehicle is started in below freezing temperatures.
Page 121: Traction Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 The “Traction Control Indicator Light,” located in the WARNING! instrument cluster, will flash when the Traction Control System is active. Tilting the steering wheel column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “TRACTION SYS DISABLED” message will be displayed When the Traction Control System has been turned off in the Electronic Vehicle Information Center (EVIC). using the switch, a feature of the system remains active. Refer to Section 4 of this manual.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 There are two Electronic Vehicle Information Center Service Elec Brake System (EVIC) messages associated with the Traction Control This message will be displayed if a condition exists that System. Refer to Section 4 of this manual. may require servicing the electronic brake system.
Page 124: Electronic Stability Program (Esp)- If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC STABILITY PROGRAM (ESP)— IF ESP corrects for over/understeering of the vehicle by EQUIPPED applying brakes to the appropriate wheel. Engine torque is also limited. The “ESP Indicator Light,” located in the instrument cluster, starts to flash as soon as the tires lose WARNING! traction and the ESP system becomes active.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 To turn the ESP system OFF, press the switch, located below the climate controls in the center stack, until the ESP Indicator Light in the instrument cluster turns on and the message ESP SYSTEM DISABLED appears in the Electronic Vehicle Information Center (EVIC).
Page 126 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE than the other, the system will apply the brake of the Light” in the instrument cluster goes out). Avoid spin- spinning wheel and allow more engine torque to be ning one drive wheel. This may cause serious damage to applied to the wheel that is not spinning.
Page 127: Rear Park Assist System- If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 function. The “ESP Indicator Light” will be on when the CAUTION! system is disabled or only partial function is allowed. The “ESP SYSTEM DISABLED” message and the “ESP Indi- The manufacturer recommends towing with all four cator Light”...
Page 128: Rear Park Assist Sensors
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Rear Park Assist System can be active only when the Rear Park Assist Warning Display shifter is in R (Reverse). If the Rear Park Assist System is The Rear Park Assist Warning Display, located in the enabled at this shifter position, the system will be active headliner near the flipper glass, provides both visual and until the vehicle speed is increased to approximately 11.2...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 When the ignition is changed to the RUN/ON position, When the detected obstacle is about 11.8 inches (30 cm) the warning display will turn ON all of its LEDs for from the rear fascia, the warning display will actuate a about 1 sec.
Page 130: Enable/Disable The Rear Park Assist System
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enable/Disable the Rear Park Assist System When the switch is pressed to disable the system, the The Rear Park Assist System can be enabled and disabled instrument cluster will display the PARK ASSIST DIS- with a switch located in the switch bank of the instru- ABLED message.
Page 131: Cleaning The Rear Park Assist System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Cleaning the Rear Park Assist System WARNING! Clean the Rear Park Assist Sensors with water, car wash • soap and a soft cloth. Do not use rough or hard cloths. Do Drivers must be careful when backing up even when not scratch or poke the sensors.
Page 132: Adjustable Pedals - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Clean all four Rear Park Assist Sensors regularly, Ultrasonic noise from airbrakes of nearby trucks, air taking care not to scratch or damage them. The sensors powered jackhammers and air powered shop tools, to must not be covered with ice, snow, slush, mud, dirt or name a few, will cause the Rear Park Assist System to be debris.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be ad- justed when the system is locked out (“Adjustable Pedal Disabled —...
Page 134: Electronic Speed Control
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL To Activate When engaged, this device takes over accelerator opera- Press the ON·OFF button to turn the system ON. To turn tions at speeds greater than 25 mph (40 km/h) for 5.7L the system OFF, press the ON·OFF button again.
Page 135: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 To decrease speed while Speed Control is ON and SET, To Resume Speed To resume a previously set speed, press and release the press and hold the DECEL button. Release the button RES·ACCEL button. Resume can be used at any speed when the desired speed is reached, and the new speed above 25 mph (40 km/h) for 5.7L engines, and 30 mph (48 will be set.
Page 136: Driving Up Or Down Hills
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to lock out overdrive. Press the TOW/HAUL switch on vehicle to gain speed, press the brake pedal, which will the lower center switch bank (below the Heating/Air disengage the Speed Control and help slow your vehicle. Conditioning controls).
Page 137: Overhead Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 OVERHEAD CONSOLE — IF EQUIPPED Courtesy/Reading Lights The overhead console contains courtesy/reading lights, At the forward end of the console are two courtesy/ an optional universal garage door opener (HomeLink ), reading lights. storage for sunglasses, and optional power sunroof switches.
Page 138: Garage Door Opener - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED WARNING! The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- A moving garage door can cause injury to people and ate devices such as garage door openers, motorized pets in the path of the door.
Page 139: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and WARNING! release only when the EVIC display shows “CHANNELS CLEARED” (after 20 seconds). Do not hold the buttons Vehicle exhaust contains carbon monoxide, a danger- for longer than 30 seconds and do not repeat step one to ous gas.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 3. Simultaneously press and hold both the HomeLink 3), programming is complete and your device should button that you want to train and the hand-held trans- activate when the HomeLink button is pressed and mitter buttons.
Page 142: Canadian Programming/Gate Programming
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. At the garage door opener receiver (motor-head unit) NOTE: To program the remaining two HomeLink but- in the garage, locate the learn or smart button. This tons, begin with Programming step two. Do not repeat can usually be found where the hanging antenna wire is step one.
Page 143: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 3. Continue to press and hold the HomeLink button Erasing HomeLink Buttons while you press and release every two seconds ( cycle ) To erase programming from the three buttons (individual your hand-held transmitter until the frequency signal has buttons cannot be erased but can be reprogrammed - successfully been accepted by HomeLink.
Page 144: Security
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. The EVIC display will show “CHANNEL X TRANS- This device complies with part 15 of FCC rules and with MIT” (where X is Channel 1, 2, or 3) for 20 seconds and RSS-210 of Industry Canada.
Page 145: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children in a vehicle, with the keys in visors on the overhead console. the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 146: Opening Sunroof - Express
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Express sunroof will automatically retract. Remove the obstruc- Press the switch rearward and release, and the sunroof tion if this occurs. Next, press the switch forward and will open automatically from any position. The sunroof release to Express Close.
Page 147: Sunshade Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open.
Page 148: Power Outlet
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER OUTLET To the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. Rear Power Outlet The power outlets are a direct feed from the battery so they receive power whether the ignition is in the ON or...
Page 149: Cup Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 CUP HOLDERS CAUTION! In the center console there are two cup holders for the front seat passengers. Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 150: Cargo Area Features
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE cup depression towards the passenger seat, but the top CARGO AREA FEATURES surface will not be flush with the console surface. Cargo Light The rear passengers have access to two cup holders that The cargo area light is activated by opening the liftgate, pull out from the lower center of the rear seat.
Page 151: Rear Storage Compartment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Rear Storage Compartment Retractable Cargo Area Cover — If Equipped The rear storage compartment is located behind the left NOTE: The purpose of this cover is for privacy, not to rear seat. secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo.
Page 152 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. The liftgate may be opened with the cargo cover in WARNING! place. In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle.
Page 153: Cargo Tie-Down Hooks
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Cargo Tie-Down Hooks WARNING! The tie-downs located on cargo area floor should be used to safely secure loads when vehicle is moving. Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose.
Page 154: Cargo Load Floor
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not carry loads which exceed the load limits WARNING! described on the label attached to the left door or left door center pillar. Refer to “Vehicle Loading” in Sec- To help protect against personal injury, passengers tion 5 for additional information on cargo weights.
Page 155: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the wash function. The wash pump will continue to If the rear wiper is operating when the ignition is turned operate as long as the button is pressed. Upon release, the OFF, the wiper will automatically return to the “Park” wipers will cycle three times before returning to the set position.
Page 157: Roof Luggage Rack - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 NOTE: The optional cross rails have seven specific ROOF LUGGAGE RACK — IF EQUIPPED External racks do not increase the total load carrying locations identified by a feature on both the side rail and capacity of the vehicle.
Page 158 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Cargo must be securely tied before driving your To prevent damage to the roof of your vehicle, DO NOT vehicle. Improperly secured loads can fly off the carry any loads on the roof rack without cross rails installed.
Page 159: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel And Interior Controls ..162 Radio Broadcast Signals ....184 Instrument Cluster ..... . 163 Two Types Of Signals .
Page 160 160 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode For CD Operating Instructions - Satellite Radio — If Audio Play) ......191 Equipped .
Page 161 UNDERSTANDING YOUR INSTRUMENT PANEL 161 PTY Button Scan ..... 209 Climate Controls — Manual ....213 PTY Button Seek .
Page 162: Instrument Panel And Interior Controls
162 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND INTERIOR CONTROLS...
Page 163: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 163 INSTRUMENT CLUSTER...
Page 164: Instrument Cluster Description
164 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 3. Turn Signal Indicator Light The arrow will flash with the exterior turn signal 1. Speedometer when the turn signal lever is operated. Indicates vehicle speed. If the vehicle electronics sense that the vehicle has 2.
Page 165 UNDERSTANDING YOUR INSTRUMENT PANEL 165 Certain conditions such as a loose or missing gas cap, 7. Anti-Lock Brake Warning Light poor fuel quality, etc. may illuminate the light after This light monitors the Anti-Lock Brake System. engine start. The vehicle should be serviced if the light The light will turn on when the ignition switch is stays on through several of your typical driving cycles.
Page 166 166 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Tachometer Do not operate the vehicle until the cause is corrected. The red segments indicate the maximum permissible This light does not show how much oil is in the engine. engine revolutions-per-minute (r.p.m. x 1000) for each The engine oil level must be checked under the hood.
Page 167 UNDERSTANDING YOUR INSTRUMENT PANEL 167 tire to overheat and can lead to tire failure. Underinfla- 12. Tire Pressure Monitor Warning Light This light will turn on continuously when there tion also reduces fuel efficiency and tire tread life, and is a low tire pressure condition. The light will may affect the vehicle’s handling and stopping ability.
Page 168 168 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Vehicle Information Center Display CAUTION! When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) Driving with a hot engine cooling system could messages. Refer to “Electronic Vehicle Information Cen- damage your vehicle.
Page 169 UNDERSTANDING YOUR INSTRUMENT PANEL 169 U.S. federal regulations require that upon transfer of 17. Seat Belt Reminder Light When the ignition switch is first turned ON, this vehicle ownership, the seller certify to the purchaser the light will turn on for 5 to 8 seconds as a bulb check. correct mileage that the vehicle has been driven.
Page 170 170 UNDERSTANDING YOUR INSTRUMENT PANEL 22. Electronic Throttle Control (ETC) Warning Light — 23. Front Fog Light Indicator Light— If Equipped If Equipped (5.7L Engine Only) This light shows the front fog lights are ON. This light informs you of a problem with the Electronic Throttle Control system.
Page 171: Electronic Vehicle Information Center - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 171 • TURN SIGNAL ON ELECTRONIC VEHICLE INFORMATION CENTER — IF EQUIPPED • PERFORM SERVICE • KEY NOT PROGRAMMED — DAMAGED KEY • KEY NOT PROGRAMMMED — INVALID KEY • KEY NOT PROGRAMMED — EXCEEDED KEY PRO- GRAM LIMIT •...
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL • LIFTGATE/DOOR OPEN (with graphic) • LIFTGLASS/HOOD OPEN (with graphic) • LIFTGATE/DOORS OPEN (with graphic) • WASHER FLUID LOW (with graphic) • LIFTGLASS OPEN (with graphic) • FUEL LOW (with graphic) • HOOD OPEN (with graphic) •...
Page 173 UNDERSTANDING YOUR INSTRUMENT PANEL 173 • WARNING! LIMIT SPEED • PEDAL ADJUST DISABLED — CRUISE CONTROL • CHECK GAS CAP • PEDAL ADJUST DISABLED — SHIFTER IN RE- • ESP SYSTEM DISABLED VERSE • SERVICE ELEC BRAKE SYSTEM • SERVICE TIRE PRESS SYSTEM •...
Page 174: Customer Programmable Features
174 UNDERSTANDING YOUR INSTRUMENT PANEL Customer Programmable Features computer functions. Press the STEP button while in this Press the MENU button until one of the display choices display selects English, Espanol, or Francais. As you following appears: continue the displayed information will be shown in the selected language.
Page 175 UNDERSTANDING YOUR INSTRUMENT PANEL 175 Display U.S. or Metric? Remote Unlock Driver’s Door 1st? Pressing the STEP button when in this display selects US When this feature is selected only the driver’s door will or Metric. The overhead console and instrument panel unlock on the first press of the remote keyless entry displays will be in the selected units.
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL memory set position using the door mounted switch. Headlamp Delay Pressing the STEP button when in this display will select When this feature is selected the driver can choose, when “Yes” or “No.” exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on.
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 177 this display will select “Low Beam” or “Low/High Front Wipers Rain Sense? Beam.” Refer to “Lights — SmartBeams” in Section 3 of Pressing the STEP button when in this display will select this manual. “Manual” or “Rain Sense.” NOTE: System will activate at or above 20 mph (32 Service Interval km/h).
Page 178: Compass/Temperature/Trip Computer
178 UNDERSTANDING YOUR INSTRUMENT PANEL Easy Entry/Exit Seat? (Available with Memory Seat Compass/Temperature/Trip Computer Only) This display provides the outside temperature, one of the When this feature is selected, the driver’s seat moves eight compass headings to indicate the direction the rearward 2 inches (5 cm) or to the farthest rearward vehicle is facing, and vehicle trip information.
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 179 WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Page 180: Trip Computer
180 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Computer This feature, located in the instrument cluster, displays the following information when the display is in the “Compass/Temperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 181 Reset Button Average Fuel Economy Press the RESET button (for 5 seconds) to reset the Shows the average fuel economy since the last reset. display you are in. Press and hold the RESET button (for Distance To Empty 10 seconds) to reset all of the displays.
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Display — If Equipped Miles to Service Shows the current pressure of all 4 road tires. Shows the distance remaining to require service. NOTE: This display can be reset to the set service interval by pressing and holding the RESET button for 3 seconds.
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 183 Manual Compass Calibration If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration” mode. NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass.
Page 184: Radio General Information
184 UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the C/T but- ton approximately 5 to 10 seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 185: Two Types Of Signals
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Two Types of Signals FM Reception There are two basic types of radio signals... AM or Because FM transmission is based on frequency varia- Amplitude Modulation, in which the transmitted sound tions, interference that consists of amplitude variations causes the amplitude, or height, of the radio waves to can be filtered out, leaving the reception relatively clear, vary...
Page 186: Sales Code Raq - Am/Fm/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (Ves) Capabilities
186 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO Operating Instructions - Radio Mode WITH OPTIONAL SATELLITE RADIO, HANDS NOTE: The ignition switch must be in the ON or ACC FREE PHONE, AND VEHICLE ENTERTAINMENT position to operate the radio. SYSTEMS (VES) CAPABILITIES Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 187 will return. Rotating the volume control, turning the Mode Button (Radio Mode) Press the mode button repeatedly to select between the radio ON/OFF, or turning OFF the ignition will also CD player, Satellite Radio, or Vehicle Entertainment return the sound from the speakers System (VES) (if equipped).
Page 188 188 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button RW/FF (Radio Mode) Press the time button and the time of day will be Pressing the rewind/fast forward button causes the tuner displayed for 5 seconds. to search for the next frequency in the direction of the arrows.
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 189 Press the rotary TUNE control a third time and TREBLE turning the TUNE rotary knob within 5 seconds will will display. Turn the TUNE control to the right or left to allow the program format type to be selected. Many radio increase or decrease the Treble tones.
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is Program Type 16 Digit-Character Display displayed, the radio will be tuned to the next frequency News News station with the same selected PTY name. The PTY Nostalgia Nostalgia function only operates when in the FM mode.
Page 191: Operation Instructions
UNDERSTANDING YOUR INSTRUMENT PANEL 191 You may add a second station to each push-button by Operation Instructions - (CD MODE for CD Audio repeating the above procedure with this exception: Press Play) the SET/DIR button twice and SET 2 will show in the NOTE: The ignition switch must be in the ON or ACC display window.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL to the beginning of the previous selection if the CD is CAUTION! within the first 10 seconds of the current selection. This CD player will accept 4 3/4 inch (12 cm) discs MUTE Button (CD MODE for CD Audio Play) only.
Page 193: Load/Eject Button
UNDERSTANDING YOUR INSTRUMENT PANEL 193 Radio display will show EJECTING DISC when the disc LOAD/EJECT Button (CD Mode for CD Audio Play) is being ejected and prompt the user to remove the disc. LOAD/ EJECT - Load Press and hold the LOAD/ EJT button for 5 seconds and Press the LOAD/ EJECT button and the push- all CDs will be ejected from the radio.
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (CD MODE for CD Audio Play) RND/PTY Button (Random Play Button) (CD Press this button to change the display from a large CD MODE for CD Audio Play) playing time display to a small CD playing time display. Press this button while the CD is playing to activate Random Play.
Page 195: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 195 The radio uses the following limits for file systems: Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 • Maximum number of directory levels: 15 file recording media and formats are limited. When •...
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Bit rate (kbps) The radio will recognize only files with the *.mp3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.mp3 320, 256, 224, extension may cause playback problems.
Page 197: Operation Instructions
UNDERSTANDING YOUR INSTRUMENT PANEL 197 Playback of MP3 Files Operation Instructions - (CD Mode for MP3 Audio When a medium containing MP3 data is loaded, the Play) radio checks all files on the medium. If the medium SEEK Button (CD Mode for MP3 Play) contains a lot of folders or files, the radio will take more Pressing the right side of the SEEK button plays the next time to start playing the MP3 files.
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL LOAD / EJECT - Eject MSG or INFO Button (CD Mode for MP3 Play) Press the LOAD/ EJECT button and the push- Press and MSG or INFO button while playing MP3 disc. button with the corresponding number where The radio scrolls through the following TAG information: the CD was loaded and the disc will unload Song Title, Artist, File Name, and Folder Name (if avail-...
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 199 AM/FM Button (CD Mode for MP3 Play) Operating Instructions - Hands Free Phone (If Switches back to Radio mode. Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s RND/ PTY Button (CD Mode for MP3 Play) Manual.
Page 200: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
200 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REF — AM/FM/CD (SINGLE DISC) Operating Instructions - Radio Mode RADIO WITH OPTIONAL SATELLITE RADIO AND NOTE: The ignition switch must be in the ON or ACC HANDS FREE PHONE CAPABILITY position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 201 NOTE: In Hands Free Phone (if equipped) mode, the Mode Button (Radio Mode) Press the mode button repeatedly to select between the MUTE button mutes the microphone. CD player or Satellite Radio (if equipped). SCAN Button (Radio Mode) SEEK Button (Radio Mode) Pressing the SCAN button causes the tuner to search for Press and release the SEEK button to search for the next...
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure TUNE Control (Radio Mode) Turn the right side rotary control clockwise to increase or 1. Press and hold the time button until the hours blink. counter-clockwise to decrease the frequency. 2. Adjust the hours by turning the right side Tune / AM/FM Button (Radio Mode) Audio control.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 Press the rotary TUNE control a fourth time and BAL will selected within 5 seconds after pressing the SET button, be displayed. Turn the TUNE control to the right or left to the station will continue to play but will not be stored adjust the sound level from the right or left side speakers.
Page 204: Operation Instructions - Cd Mode
204 UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio Operation Instructions - CD Mode OFF, the CD will automatically be pulled into the CD NOTE: The ignition switch must be in the ON or ACC Player.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 205 SCAN Button (CD Mode) RW/FF (CD Mode) Press this button to play the first 10 seconds of each track. Press and hold the FF (Fast Forward) and the CD player To stop the scan function, press the button a second time. will begin to fast forward until FF is released.
Page 206: Operating Instructions - Hands Free Phone - If Equipped
206 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the FF button to fast forward through the SALES CODE REC — AM/FM/CD (6–DISC) RADIO tracks. Release the FF button to stop the fast forward WITH NAVIGATION SYSTEM feature. If the RW button is pressed, the current track will reverse to the beginning of the track and begin playing.
Page 207: Satellite Radio - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 207 menus and instructions for selecting a variety of destina- System Activation tions and routes, Am/FM stereo radio and six-disc CD To activate your Sirius Satellite Radio service, call the changer with MP3 capability. toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com.
Page 208: Selecting Satellite Mode In Ref Radios
208 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With REF Radios mode when any other button is pushed, the ignition is With the ignition switch in the ACCESSORY position and turned OFF, or 5 minutes has passed since any button the radio OFF, press the Eject or CD Eject (depending on was pushed.
Page 209: Selecting A Channel
UNDERSTANDING YOUR INSTRUMENT PANEL 209 A CD may remain in the radio while in the Satellite radio Storing and Selecting Pre-Set Channels mode. In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button Selecting a Channel memory.
Page 210: Pty Button Seek
210 UNDERSTANDING YOUR INSTRUMENT PANEL one and stop the search. Pressing a pre-set memory Reception Quality button during a music type scan, will call up the memory Satellite reception may be interrupted due to one of the channel and stop the search. following reasons.
Page 211: Remote Sound System Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 211 switch will increase the volume and pressing the bottom REMOTE SOUND SYSTEM CONTROLS — IF of the rocker switch will decrease the volume. EQUIPPED The remote sound system controls are located on the rear Pressing the center button will make the radio switch surface of the steering wheel.
Page 212: Cd Player
212 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player CD/DVD DISC MAINTENANCE Pressing the top of the switch once will go to the next To keep the CD/DVD discs in good condition, take the track on the CD. Pressing the bottom of the switch once following precautions: will go to the beginning of the current track or to the 1.
Page 213: Radio Operation And Cellular Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 213 The instrument panel features four dual-vane airflow RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in registers. Two registers are located on the outer ends of your vehicle can cause erratic or noisy performance from the instrument panel and two are located in the center of your radio.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL Press this button to turn on and off the air condi- CAUTION! tioning. Cool dehumidified air comes through the outlets selected by the mode selector. Press the To avoid damaging the electrical conductors of the button a second time to turn off the air conditioning.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Temperature Control Defrost The temperature of air can be selected Air is directed to the windshield through the by rotating the temperature control outlets at the base of the windshield. Air is also knob in the center. The coldest tem- directed to the front door windows through the side perature setting is on the extreme left window demister grilles.
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Use this mode to rapidly cool the inside of the vehicle. Air flows both through the outlets located in the The Recirculation mode can also be used to temporarily instrument panel and those located on the floor. Air block out outside odors, smoke, and dust.
Page 217: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Operating Tips...
Page 218: Automatic Temperature Control - If Equipped
218 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control — If Equipped The Infrared Dual-Zone Climate Control System auto- matically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face of the control unit.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 219 present. Dial in the temperature you would like the The system will automatically control recircu- system to maintain by rotating the driver’s or passenger’s lation. However, pressing this button will tem- control knob. Once the comfort level is selected the porarily put the system in recirculation mode system will maintain that level automatically using the (ten minutes).
Page 220 220 UNDERSTANDING YOUR INSTRUMENT PANEL fan will engage immediately if the defrost mode is move your mode knob to panel, panel/floor or floor, selected or if you manually select a blower speed. then hit the recirc button. This feature will reduce the possibility of window fogging.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 221...
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode Air flows both through the outlets located in the knob to one of the following positions. instrument panel and those located on the floor.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 223 NOTE: To manually control the air conditioning the CAUTION! mode selector must be moved out of the AUTO position. To avoid damaging the electrical conductors of the Press this button to turn on the rear window rear window defroster, do not use scrapers, sharp defroster and the heated side mirrors (if instruments, or abrasive window cleaners on the...
Page 224: Summer Operation
224 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Extended use of recirculation may cause the Winter Operation windows to fog. If the interior of the windows begins to Use of the air Recirculation mode during winter months fog, press the “Recirculate” icon button to return to is not recommended because it may cause window outside air.
Page 225: Window Fogging
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow and if they windshield and provide sufficient heating.
Page 227: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 230 Rocking The Vehicle ....238 Normal Starting .
Page 228 228 STARTING AND OPERATING Anti-Lock Brake System ....246 Tire Markings ......254 Vari-Lok Rear Axle —...
Page 229 STARTING AND OPERATING 229 Tire Pressure Monitoring — Premium System . . 271 Loose Fuel Filler Cap Message ... . 282 General Information ....275 Trailer Towing .
Page 230: Starting Procedures
230 STARTING AND OPERATING STARTING PROCEDURES 10 seconds, turn the key to the OFF position, wait 5 Before starting your vehicle, adjust your seat, adjust both seconds, then repeat the normal starting procedure. inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather.
Page 231: Extreme Cold Weather (Below -20°F (-29°C)
STARTING AND OPERATING 231 NOTE: To prevent damage to the starter, do not crank WARNING! the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start If the engine has been flooded, it may start to run, but not the vehicle.
Page 232: After Starting
232 STARTING AND OPERATING After Starting The engine block heater cord is located: The idle speed will automatically decrease as the engine • 3.7L/4.7L Engine — coiled and strapped to the engine warms up. oil dipstick tube. • 5.7L Engine — bundled and fastened to the injector CAUTION! harness.
Page 233: Transmission Shifting
STARTING AND OPERATING 233 TRANSMISSION SHIFTING 5–Speed Automatic Transmission The electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle, may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles.
Page 234: Gear Ranges
234 STARTING AND OPERATING Gear Ranges WARNING! P (Park) It is dangerous to shift the selector lever out of P Supplements the parking brake by locking the transmis- (Park) or N (Neutral) if the engine speed is higher sion. The engine can be started in this range. Never use P than idle speed.
Page 235 STARTING AND OPERATING 235 R (Reverse) Electronic Range Select (ERS)Operation Shift into this range only after the vehicle has come to a The Electronic Range Select (ERS) shift control allows complete stop. you to move the shifter left (-) or right (+) when the shifter is in the D (Drive) position, allowing the selection N (Neutral) of the desired top gear.
Page 236 236 STARTING AND OPERATING left “D(-)” and hold it there. The transmission will shift to NOTE: If the vehicle is started in extremely cold tem- the range from which the vehicle can best be slowed peratures, the transmission may not shift into Overdrive down.
Page 237 STARTING AND OPERATING 237 a downshift may occur. This is a normal part of the overheat protection strategy when operating in the “Tow/Haul” mode. The transmission will downshift from Overdrive to the most desirable gear if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h).
Page 238: Rocking The Vehicle
238 STARTING AND OPERATING Torque Converter Clutch gear) positions (using the ERS shift control) will demon- A feature designed to improve fuel economy is included strate that the transmission is able to shift into and out of in all automatic transmissions. A clutch within the torque Overdrive.
Page 239: Four-Wheel Drive Operation
STARTING AND OPERATING 239 The Electronic Stability Program (ESP) and NOTE: CAUTION! Traction Control (if equipped) should be turned OFF before attempting to rock the vehicle. Refer to Section 3 of When “rocking” a stuck vehicle by moving between this manual. “First”...
Page 240: Quadra-Trac Ii Operating Instructions/Precautions - If Equipped
240 STARTING AND OPERATING and Traction Control, provides resistance to any wheel shafts, the transfer case can transmit up to 100 percent of that is slipping to allow additional torque transfer to available engine torque to the front or rear drive shafts. wheels with traction.
Page 241: Shift Positions
STARTING AND OPERATING 241 Because four wheel drive provides improved traction, Shift Positions there is a tendency to exceed safe turning and stopping For additional information on the appropriate use of each speeds. Do not go faster than road conditions permit. transfer case mode position, see the information below: 4 HI WARNING!
Page 242: Shifting Procedures
242 STARTING AND OPERATING speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting Procedures 4 HI to 4 LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into N (Neutral), and raise the transfer case T-handle.
Page 243 STARTING AND OPERATING 243 LOW Indicator Lamp” in the instrument cluster will flash Neutral (N) Shift Procedure and go out when the shift is complete. Release the 1. Key ON, engine off. T-handle. 2. Vehicle stopped, with foot on brake. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition 3.
Page 244: Quadra-Drive System - If Equipped
244 STARTING AND OPERATING the EVIC (Electronic Vehicle Information Center). Refer operation is similar. Follow the Quadra-Trac II transfer to “Electronic Vehicle Information Center (EVIC)” in case shifting information, preceding this section, for Section 4 of this manual. shifting this system. Quadra-Drive System —...
Page 245 STARTING AND OPERATING 245 When parking on a hill, it is important to set the parking brake before placing the gear selector in P (Park), other- wise the load on the transmission locking mechanism may make it difficult to move the selector out of P (Park). The parking brake should always be applied when the driver is not in the vehicle.
Page 246: Anti-Lock Brake System
246 STARTING AND OPERATING To release the parking brake, pull up slightly, press the WARNING! center button, then lower the lever completely. Significant over or under inflation of tires, or mixing Be sure the parking brake is fully disengaged before sizes of tires or wheels on the vehicle can lead to loss driving.
Page 247 STARTING AND OPERATING 247 WARNING! WARNING! • The Anti-Lock Brake System (ABS) cannot pre- Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. vent the natural laws of physics from acting on the Pumping makes the stopping distance longer. Just vehicle, nor can it increase braking or steering press firmly on your brake pedal when you need to efficiency beyond that afforded by the condition...
Page 248 248 STARTING AND OPERATING • Do not “ride” the brakes by resting your foot on the CAUTION! pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping dis- The Anti-Lock Brake System is subject to possible tances, or brake damage.
Page 249: Vari-Lok Rear Axle - If Equipped
STARTING AND OPERATING 249 build up between the tire tread and the road. This ON-ROAD DRIVING TIPS hydroplaning action can cause loss of traction, braking Utility vehicles have higher ground clearance and a ability, and control. narrower track to make them capable of performing in a wide variety of off-road applications.
Page 250: Off-Road Driving Tips
250 STARTING AND OPERATING OFF-ROAD DRIVING TIPS CAUTION! NOTE: Prior to off-road driving, remove the front air When driving through water, do not exceed 5 mph (8 dam to prevent damage. The front air dam is attached to km/h). Always check water depth before entering as the lower front fascia with quarter turn fasteners, and can a precaution, and check all fluids afterward.
Page 251: Driving In Snow, Mud And Sand
STARTING AND OPERATING 251 and/or the flow rate is reduced. If you must cross Driving In Snow, Mud and Sand flowing water avoid depths in excess of 9 inches. The In heavy snow, when pulling a load, or for additional flowing water can erode the streambed causing your control at slower speeds, shift the transmission to a low vehicle to sink into deeper water.
Page 252: Traction Downhill
252 STARTING AND OPERATING If you stall or begin to lose headway while climbing a Remember, never drive diagonally across a hill-always steep hill, allow your vehicle to come to a stop and drive straight up or down. immediately apply the brakes. Restart the engine and If the wheels start to slip as you approach the crest of a shift to R (Reverse).
Page 253: After Driving Off-Road
STARTING AND OPERATING 253 • After extended operation in mud, sand, water, or After Driving Off-Road Off-road operation puts more stress on your vehicle than similar dirty conditions, have brake rotors, wheels, does most on-road driving. After going off-road it is brake linings, and axle yokes inspected and cleaned as always a good idea to check for damage.
Page 254: Multi Displacement System (Mds) - 5.7L Engine Only
254 STARTING AND OPERATING MULTI DISPLACEMENT SYSTEM (MDS) - 5.7L TIRE SAFETY INFORMATION Engine Only Tire Markings This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required.
Page 255 STARTING AND OPERATING 255 • European Metric tire sizing is based on European • Temporary Spare tires are high pressure compact design standards. Tires designed to this standard have spares designed for temporary emergency use only. the tire size molded into the sidewall beginning with Tires designed to this standard have the letter “T”...
Page 256 256 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 257 STARTING AND OPERATING 257 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 258: Tire Identification Number (Tin)
258 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire the outboard side then you will find it on the inboard side however the date code may only be on one side.
Page 259: Tire Loading And Tire Pressure
STARTING AND OPERATING 259 Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the shutface of the driver’s door, the “B”...
Page 260 260 STARTING AND OPERATING Tire and Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of...
Page 261 STARTING AND OPERATING 261 combined weight of occupants, cargo/luggage and 5. Determine the combined weight of luggage and cargo trailer tongue weight (if applicable) should never exceed being loaded on the vehicle. That weight may not safely the weight referenced here. exceed the available cargo and luggage load capacity calculated in step 4.
Page 262 262 STARTING AND OPERATING...
Page 263: Tires - General Information
STARTING AND OPERATING 263 1. Safety— WARNING! Overloading of your tires is dangerous. Overloading WARNING! can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the Improperly inflated tires are dangerous and can recommended load capacity for your vehicle. Never cause accidents.
Page 264: Tire Inflation Pressures
264 STARTING AND OPERATING 2. Economy— Tire Inflation Pressures Improper inflation pressures can cause uneven wear The proper cold tire inflation pressure is listed on either patterns to develop across the tire tread. These abnormal the face of the driver’s door, or the driver’s side “B” pillar. wear patterns will reduce tread life resulting in a need for earlier tire replacement.
Page 265: High Speed Operation
STARTING AND OPERATING 265 more often if subject to a wide range of outdoor tempera- High Speed Operation tures, as tire pressures vary with temperature changes. WARNING! Inflation pressures specified on the label are always “Cold Inflation Pressure.” Cold inflation pressure is High speed driving with your vehicle under load is defined as the tire pressure after the vehicle has been idle dangerous.
Page 266: Radial-Ply Tires
266 STARTING AND OPERATING Radial-Ply Tires Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). WARNING! Combining radial ply tires with other types of tires WARNING! on your vehicle will cause your vehicle to handle poorly.
Page 267: Tread Wear Indicators
STARTING AND OPERATING 267 Tread Wear Indicators Replacement Tires These indicators are narrow strips 1/16 inch (1.6 mm) The tires on your new vehicle provide a balance of many thick and are found in the tread pattern grooves. characteristics. They should be inspected regularly for wear and correct inflation pressure.
Page 268: Alignment And Balance
268 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size specified for your vehicle. Some combinations of un- may result in false speedometer and odometer read- approved tires and wheels may change suspension ings.
Page 269: Tire Pressure Monitor System
STARTING AND OPERATING 269 Tires may also cause the vehicle to pull left or right. The “Tire Pressure Monitoring Indicator Lamp” Alignment will not correct this problem. See your dealer will illuminate in the instrument cluster, and an for proper diagnosis of the problem. audible chime will be activated when one or more tire pressures is low.
Page 270 270 STARTING AND OPERATING colored Indicator Lamp. A sensor is located in the spare CAUTION! wheel if the vehicle is equipped with a matching full size spare wheel and tire assembly. The TPM system has been optimized for the original equipment tires and wheels.
Page 271: Tire Pressure Monitoring - Premium System
STARTING AND OPERATING 271 Tire Pressure Monitoring — Premium System CAUTION! The Tire Pressure Monitor System (TPM) system uses wireless technology with wheel rim mounted electronic After inspecting or adjusting the tire pressure al- sensors to monitor tire pressure levels. Sensors mounted ways reinstall the valve stem cap.
Page 272 272 STARTING AND OPERATING when a system fault is detected. The flash cycle will various Tire Pressure Monitoring System Display Mes- repeat every ten minutes or until the fault condition is sages in the EVIC, and an amber colored Indicator Lamp. removed and reset.
Page 273 STARTING AND OPERATING 273 will illuminate continuously (solid) and shall remain Inspect all tires for proper inflation pressure, once the illuminated until the warning condition is removed/ proper tire pressure has been set, the TPM system reset. warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 15 mph (24 NOTE: The Indicator Lamp will only illuminate for the km/h).
Page 274 274 STARTING AND OPERATING CAUTION! CAUTION! The TPM system has been optimized for the original After inspecting or adjusting the tire pressure al- equipment tires and wheels. TPM system pressures ways reinstall the valve stem cap. This will prevent have been established for the tire size equipped on moisture and dirt from entering the valve stem, your vehicle.
Page 275: General Information
STARTING AND OPERATING 275 General Information TIRE CHAINS This device complies with part 15 of the FCC rules and Certain models have sufficient tire-to-body clearance to RSS 210 of Industry Canada. Operation is subject to the allow use of tire chains. Install chains on rear tires only. following conditions: Follow these recommendations to guard against damage and excessive tire and chain wear:...
Page 276: Tire Rotation Recommendations
276 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS NOTE: The Premium Tire Pressure Monitor System will Tires on the front and rear axles of vehicles operate at automatically locate the pressure values displayed in the different loads and perform different steering, handling, correct vehicle position following a tire rotation.
Page 277: Fuel Requirements
STARTING AND OPERATING 277 using high quality unleaded gasoline having an octane FUEL REQUIREMENTS range of 87 to 89. The manufacturer recommends the use 3.7/4.7L Engines (If Equipped) of 89 octane for optimum performance. The use of All engines (except 5.7L engines) are de- premium gasoline is not recommended.
Page 278: Reformulated Gasoline
278 STARTING AND OPERATING Over 40 auto manufacturer’s world wide have issued and Gasoline/Oxygenate Blends endorsed consistent gasoline specifications (the World- Some fuel suppliers blend unleaded gasoline with oxy- wide Fuel Charter, WWFC) to define fuel properties genates such as 10% ethanol, MTBE, and ETBE. Oxygen- necessary to deliver enhanced emissions, performance, ates are required in some areas of the country during the and durability for your vehicle.
Page 279: Mmt In Gasoline
STARTING AND OPERATING 279 MMT In Gasoline Materials Added To Fuel MMT is a manganese containing metallic additive that is All gasoline sold in the United States is required to blended into some gasoline to increase octane. Gasoline contain effective detergent additives. Use of additional blended with MMT provides no performance advantage detergents or other additives is not needed under normal beyond gasoline of the same octane number without...
Page 280: Carbon Monoxide Warnings
280 STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition Carbon Monoxide Warnings malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or WARNING! some light smoke, your engine may be out of tune or malfunctioning and may require immediate service.
Page 281: Fuel Tank Filler Cap (Gas Cap)
STARTING AND OPERATING 281 • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 282: Loose Fuel Filler Cap Message
282 STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control To avoid fuel spillage and overfilling, do not “top system could result from using an improper fuel cap off” the fuel tank after filling. (gas cap). A poorly fitting cap could let impurities into the fuel system.
Page 283: Trailer Towing
STARTING AND OPERATING 283 WARNING! WARNING! • Remove the fuel cap (gas cap) slowly to prevent A fire may result if gasoline is pumped into a fuel spray from the filler neck which may cause portable container that is inside of a vehicle. You injury.
Page 284 284 STARTING AND OPERATING manual. When your vehicle is used for trailer towing, the vehicle and trailer. Failure to load trailers heavier never exceed the gross axle weight rating (GAWR) by the in front is the cause of many trailer related accidents. addition of: •...
Page 285: Trailer And Tongue Weight
STARTING AND OPERATING 285 • Make certain that the load is secured in the trailer and Trailer and Tongue Weight will not shift during travel. Gross Trailer Weight (GTW) means the weight of the trailer plus the weight of all cargo, consumables and •...
Page 286: Trailer Tow Wiring
286 STARTING AND OPERATING Trailer Tow Wiring The Trailer Tow Package includes a 4 and 7 pin wiring harness located at the rear underbody of the vehicle. NOTE: Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice wiring to the brake circuits.
Page 287: Cooling System Tips-Trailer Towing
STARTING AND OPERATING 287 Cooling System Tips—Trailer Towing To reduce potential for engine and transmission over- heating in high ambient conditions, take the following actions: • City Traffic When stopped, put transmission in N (Neutral) and increase engine idle speed. •...
Page 288: Trailer Classifications
288 STARTING AND OPERATING TRAILER CLASSIFICATIONS Class Max. GTW (Gross Trailer Wt.) Frontal Area Length Class I - Light Duty 2,000 lbs. (907 kg) 32 ft2 20 ft Class II - Medium Duty 3,500 lbs. (1 587 kg) 40 ft2 20 ft Class III - Heavy Duty 5,000 lbs.
Page 289: Trailer Towing Capability
STARTING AND OPERATING 289 TRAILER TOWING CAPABILITY Engine Model GVWR GCWR Hitch Type Max. GTW Max. Tongue Wt. (Gross Vehice Wt. (Gross Combined (Gross Trailer Wt.) (See Note 1) Rating) Wt. Rating) 3.7L 5,700 lbs (2 585 kg) 8,000 lbs (3 629 kg) Class II 3,500 lbs (1 587 kg) 525 lbs (238 kg)
Page 290: Recreational Towing (Behind Motorhome, Etc.)
290 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND Towing — Quadra–Trac II /Quadra–Drive II 4WD MOTORHOME, ETC.) Models Towing – 2WD Models CAUTION! Recreational towing is allowed ONLY if the driveshaft is removed. Towing with the rear wheels on the ground Internal damage to the transfer case will occur if a while the driveshaft is connected can result in severe front or rear wheel lift is used when recreational...
Page 291 STARTING AND OPERATING 291 6. Shut the engine OFF and place the ignition key into CAUTION! the unlocked OFF position. It is necessary to follow these steps to be certain that 7. Shift transmission into P (Park). the transfer case is fully in N (Neutral) before 8.
Page 292 292 STARTING AND OPERATING Shifting Out Of Neutral (N) WARNING! Use the following procedure to prepare your vehicle for normal usage. You or others could be injured if you leave the vehicle unattended with the transfer case in the N 1.
Page 293: Snow Plow
STARTING AND OPERATING 293 SNOW PLOW WARNING! Snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The Do not add a snow plow, winches, or any other airbag crash sensors may be affected by the change in the aftermarket equipment to the front of your vehicle.
Page 295: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....296 Jacking Instructions ....300 If Your Engine Overheats .
Page 296: Hazard Warning Flashers
296 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle.
Page 297: If Your Engine Overheats
WHAT TO DO IN EMERGENCIES 297 IF YOUR ENGINE OVERHEATS CAUTION! In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- Driving with a hot cooling system could damage tion. your vehicle. If the temperature gauge reads “H”, pull over and stop the vehicle.
Page 298: Jacking And Tire Changing
298 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location The scissor-type jack and tire changing tools are located in a compartment behind the second row seat. WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
Page 299: Spare Tire Stowage
WHAT TO DO IN EMERGENCIES 299 Spare Tire Stowage Spare Tire Removal The spare tire is stowed under the rear of the vehicle by Fit the jack handle extension over the drive nut. Use the means of a cable winch mechanism. To remove or stow the Lug Wrench to rotate the nut counter clockwise until the spare, use the jack handle to rotate the “spare tire drive”...
Page 300: Preparations For Jacking
300 WHAT TO DO IN EMERGENCIES • Block both the front and rear Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or of the wheel diagonally oppo- slippery areas, set the parking brake and place the gear site of the jacking position.
Page 301 WHAT TO DO IN EMERGENCIES 301 3. Assemble the jack and jacking tools as shown. Connect Ensure the jack is closest to the inside of the wheel when jack handle driver (A) to two extensions (B), then to the jacking on the rear axle. Do not raise the vehicle until lug wrench (C).
Page 302 302 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7.
Page 303: Jump Starting Procedure
WHAT TO DO IN EMERGENCIES 303 nuts until each nut has been tightened twice. Correct or damage to the wheel face. Continue winching up the wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt tire until you hear the winch “ratchet” three times. about the correct tightness, have them checked with a Double check to ensure the tire is snug against the torque wrench by your authorized dealer or at a service...
Page 304 304 WHAT TO DO IN EMERGENCIES without letting the vehicles touch. Set the parking brake, 7. When removing the jumper cables, reverse the above place the transmission in P (Park), and turn the ignition sequence exactly. Be careful of the moving belts and fan. to OFF for both vehicles.
Page 305: Emergency Tow Hooks - If Equipped
WHAT TO DO IN EMERGENCIES 305 when attaching clamps. If acid splashes in eyes or on WARNING! skin, flush the area immediately with large amounts of water. Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic •...
Page 306: Towing A Disabled Vehicle
306 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE CAUTION! 2WD Models Only Tow hooks are for emergency use only, to rescue a Provided the transmission is operable, tow only in N vehicle stranded off road. Do not use tow hooks for (Neutral) at speeds not exceeding 30 mph (48 km/h), for tow truck hookup or highway towing.
Page 307: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 3.7L Engine ......310 Maintenance Procedures ....316 4.7L Engine .
Page 308 308 MAINTAINING YOUR VEHICLE Maintenance-Free Battery ....324 Appearance Care And Protection From Corrosion ......340 Air Conditioner Maintenance .
Page 309 MAINTAINING YOUR VEHICLE 309 Rear Tail, Stop, Turn Signal, And Back-Up Recommended Fluids, Lubricants And Genuine Lights ......355 Parts .
Page 310: 3.7L Engine
310 MAINTAINING YOUR VEHICLE 3.7L ENGINE...
Page 311: L Engine
MAINTAINING YOUR VEHICLE 311 4.7L ENGINE...
Page 312: 5.7L Engine
312 MAINTAINING YOUR VEHICLE 5.7L ENGINE...
Page 313: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 313 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 314: Emissions Inspection And Maintenance Programs
314 MAINTAINING YOUR VEHICLE cap until a clicking sound is heard. This is an indication is functioning and is not on when the engine is running, that the gas cap is properly tightened. Press the odometer and that the OBD (On Board Diagnostic) system is ready reset button to turn the message off.
Page 315: Replacement Parts
MAINTAINING YOUR VEHICLE 315 4. As soon as you turn your key to the ON position, you you may need to do nothing more than drive your will see your MIL symbol come on as part of a normal vehicle as you normally would in order for your OBD bulb check.
Page 316: Dealer Service
316 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your dealer has the qualified service personnel, special The pages that follow contain the required maintenance tools and equipment to perform all service operations in services determined by the engineers who designed your an expert manner.
Page 317 MAINTAINING YOUR VEHICLE 317 The best time to check the engine oil level is about 5 Change Engine Oil minutes after a fully warmed engine is shut off or before Road conditions as well as your kind of driving affect the starting the engine after it has sat overnight.
Page 318 318 MAINTAINING YOUR VEHICLE If ANY of these apply to you, then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance recommenda- tions in “Maintenance Schedule B.” If none of these apply to you, then change your engine oil every 6,000 miles (10 000 km) or 6 months, whichever comes first.
Page 319 MAINTAINING YOUR VEHICLE 319 American Petroleum Institute (API) Engine Oil Engine Oil Viscosity (5.7L Engines) Identification Symbol SAE 5W-20 engine oil is recommended for all operating This symbol means that the oil has temperatures. This engine oil improves low tempera- been certified by the American ture starting and vehicle fuel economy.
Page 320: Drive Belts - Check Condition And Tension
320 MAINTAINING YOUR VEHICLE Materials Added to Engine Oils Engine Oil Filter Selection The manufacturer strongly recommends against the ad- All of the manufacturer’s engines have a full-flow type dition of any additives (other than leak detection dyes) to disposable oil filter. Use a filter of this type for replace- engine oil.
Page 321: Spark Plugs
MAINTAINING YOUR VEHICLE 321 Special tools are required to properly measure tension Under normal operating conditions, the catalytic con- and to restore belt tension to factory specifications. Also, verter will not require maintenance. However, it is im- check belt routing to make sure there is no interference portant to keep the engine properly tuned to assure between the belts and other engine components.
Page 322 322 MAINTAINING YOUR VEHICLE • Do not shut off the engine or interrupt the ignition WARNING! when the transmission is in gear and the vehicle is in motion. A hot exhaust system can start a fire if you park over materials that can burn.
Page 323: Ignition Cables
MAINTAINING YOUR VEHICLE 323 Ignition Cables Air Cleaner Filter Replace the ignition cables (5.7L engines only) at the Under normal driving conditions, replace the air filter at mileage interval shown in the maintenance charts. the intervals shown on “Maintenance Schedule A.” If, however, you drive the vehicle frequently under dusty or Crankcase Emission Control System severe conditions, the filter element should be inspected...
Page 324: Maintenance-Free Battery
324 MAINTAINING YOUR VEHICLE Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. WARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery.
Page 325: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 325 WARNING! CAUTION! • Use only refrigerants and compressor lubricants It is essential when replacing the cables on the approved by the manufacturer for your air condi- battery that the positive cable is attached to the tioning system. Some unapproved refrigerants are positive post and the negative cable is attached to the flammable and can explode, injuring you.
Page 326: Power Steering Fluid Check
326 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling CAUTION! R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- Do not use Automatic Transmission Fluid (ATF) or tection Agency and is an ozone-saving product. How- other types of power steering fluids when servicing ever, the manufacturer recommends that air conditioning the power steering system of this vehicle.
Page 327: Body Lubrication
MAINTAINING YOUR VEHICLE 327 wiped clean to remove dust and grit; after lubricating WARNING! excess oil and grease should be removed. Particular attention should also be given to hood latching compo- Fluid level should be checked on a level surface with nents to insure proper function.
Page 328: Windshield Washers - Front And Rear
328 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods the reservoir with windshield washer solvent (not may cause deterioration of the wiper blades. Always use antifreeze/coolant) and operate the system for a few washer fluid when using the wipers to remove salt or dirt seconds to flush out the residual water.
Page 329: Cooling System
MAINTAINING YOUR VEHICLE 329 have an authorized technician inspect the complete ex- Engine Coolant Checks haust system and adjacent body areas for broken, dam- Check antifreeze/coolant protection every 12 months aged, deteriorated, or mispositioned parts. Open seams (before the onset of freezing weather, where applicable). or loose connections could permit exhaust fumes to seep If antifreeze/coolant is dirty or rusty in appearance, the into the passenger compartment.
Page 330 330 MAINTAINING YOUR VEHICLE the coolant recovery bottle. DO NOT REMOVE THE CAUTION! COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Mixing of antifreeze/coolant other than the specified HOAT antifreeze/coolant may result in decreased Cooling System — Drain, Flush, And Refill corrosion protection and engine damage.
Page 331 MAINTAINING YOUR VEHICLE 331 Use only high purity water such as distilled or deionized Adding Engine Coolant Your vehicle has been built with an improved antifreeze/ water when mixing the water/antifreeze (coolant) solu- coolant that allows extended maintenance intervals. This tion.
Page 332 332 MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any children, do not store ethylene glycol-based antifreeze/ accumulation of foreign material on the sealing surfaces. coolant in open containers or allow it to remain in puddles on the ground.
Page 333 MAINTAINING YOUR VEHICLE 333 When additional antifreeze/coolant is needed to main- coolant needs to be added, contents of coolant recov- tain the proper level, it should be added to the coolant ery bottle must also be protected against freezing. bottle. Do not overfill. •...
Page 334: Hoses And Vacuum/Vapor Harnesses
334 MAINTAINING YOUR VEHICLE ONLY the correct type thermostat. Other designs may are present. Components should be replaced immedi- result in unsatisfactory cooling performance, poor gas ately if there is any evidence of degradation that could mileage, and increased emissions. cause failure.
Page 335 MAINTAINING YOUR VEHICLE 335 NOTE: Inspection of brake hoses should be done when- Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, ever the brake system is serviced and every engine oil inspect surface of hoses for evidence of heat and me- change.
Page 336: Automatic Transmission
336 MAINTAINING YOUR VEHICLE fluid reservoir. With disc brakes, fluid level can be WARNING! expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be Overfilling the brake fluid reservoir can result in needed.
Page 337 MAINTAINING YOUR VEHICLE 337 Genuine Parts for correct fluid type. It is important that is sealed and should not be tampered with. Your autho- the transmission fluid be maintained at the prescribed rized dealer has the proper tools to ensure that the fluid level using the recommended fluid.
Page 338 338 MAINTAINING YOUR VEHICLE 5. Remove the dipstick, wipe it clean and reinsert it until (upper) reference holes when the transmission reaches seated. 180°F (82°C). Remember it is best to check the level at the normal operating temperature. 6. Remove the dipstick again and note the fluid level on both sides.
Page 339: Transfer Case
MAINTAINING YOUR VEHICLE 339 Special Additives Drain The manufacturer recommends against the addition of First remove fill plug, then remove drain plug. Recom- any additives to the transmission. Exception to this mended tightening torque for drain and fill plugs is policy is the use of special dyes to aid in detecting fluid 15–25 ft.
Page 340: Front/Rear Axle Fluid
340 MAINTAINING YOUR VEHICLE Front/Rear Axle Fluid Appearance Care And Protection From Corrosion Front Axle Fluid Level Check Protection of Body and Paint from Corrosion Lubricant should be to the bottom of the oil fill hole. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 341 MAINTAINING YOUR VEHICLE 341 • Insects, tree sap and tar. CAUTION! • Salt in the air near seacoast localities. Do not use abrasive or strong cleaning materials • Atmospheric fallout/industrial pollutants. such as steel wool or scouring powder, which will scratch metal and painted surfaces.
Page 342 342 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or not use scouring pads or metal polishes. Avoid auto- similar cause which destroys the paint and protective matic car washes that use acidic solutions or harsh coating, have your vehicle repaired as soon as pos- brushes that may damage the wheels’...
Page 343 MAINTAINING YOUR VEHICLE 343 be removed easily with a soft cloth and Mopar Total WARNING! Clean. Care should be taken to avoid soaking the leather with any liquid. Please do not use polishes, oils, cleaning Do not use volatile solvents for cleaning purposes. fluids, solvents, detergents, or ammonia based cleaners Many are potentially flammable, and if used in to clean the leather.
Page 344 344 MAINTAINING YOUR VEHICLE If the belts need cleaning, use a mild soap solution or vegetation or brush that could become a fire hazard, or lukewarm water. Do not remove the belts from the conceal damage to fuel lines, brake hoses, axle pinion vehicle to wash them.
Page 345: Fuse Panel
MAINTAINING YOUR VEHICLE 345 FUSE PANEL Cavity Fuse/Color Description 30 Amp Pink Audio Amp (B+) Interior Fuses The fuse panel is on the lower instrument panel just to 15 Amp Blue Sunroof (B+) the left of the steering column. 10 Amp Red Htd Mirror (EBL) 20 Amp Yellow Rr Pwr Out (B+) 10 Amp Red...
Page 346: Underhood Fuses (Power Distribution Center)
346 MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Cavity Fuse/Color Description 10 Amp Red SCM, Cluster OBD (B+) 15 Amp Blue Flipper Glass (B+) 10 Amp Red OCM (R/S) 10 Amp Red WCM, Cluster (R/S) 15 Amp Blue Autowipe (Accy Delay) 15 Amp Blue Rear Wiper (B+) 10 Amp Red...
Page 347 MAINTAINING YOUR VEHICLE 347 Cavity Fuse/Color Description Cavity Fuse/Color Description 40 Amp Green HVAC Blower Spare 30 Amp Pink Power Outlets 20 Amp Yellow TCM/AC Clutch 30 Amp Pink Rr Wiper/Ign R/O 20 Amp Yellow Ign Sw 30 Amp Pink ABS Pump 20 Amp Yellow PCM Batt (Gasoline Only)
Page 348: Underhood Fuses (Integrated Power Module)
348 MAINTAINING YOUR VEHICLE Underhood Fuses (Integrated Power Module) Cavity Fuse/Color Description Micro Relay TCM Rly (Gasoline Only) Micro Relay Starter Rly Micro Relay AC Clutch Rly Micro Relay Fuel Pump Rly Mini Relay Cabin Htr 3 Rly (Diesel Only) Mini Relay Cabin Htr 2 Rly (Diesel Only)
Page 349 MAINTAINING YOUR VEHICLE 349 Cavity Fuse/Color Description Cavity Fuse/Color Description Micro Relay Wiper On/Off Rly 20 Amp Yellow Rear Fogs Micro Relay Wiper Hi/Lo Rly 20 Amp Yellow FCM Batt #1 Micro Relay Horn Rly 20 Amp Yellow Lt T-Tow Stop/Turn Micro Relay Rear Fog Rly (BUX Only) 20 Amp Yellow...
Page 350: Vehicle Storage
350 MAINTAINING YOUR VEHICLE VEHICLE STORAGE REPLACEMENT BULBS If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. Interior Lights Bulb Type You may: Glove Box Light ......194 Grab Handle Light .
Page 351: Bulb Replacement
MAINTAINING YOUR VEHICLE 351 BULB REPLACEMENT Exterior Lights Bulb Type Front Park/Turn Light (Laredo) ... . 3157A Head Light Front Side Marker (Limited) ....194NA 1.
Page 352 352 MAINTAINING YOUR VEHICLE 3. Turn the low or high beam bulb 1/4 turn counter CAUTION! clockwise to remove from housing. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
Page 353: Front Turn Signal
MAINTAINING YOUR VEHICLE 353 3. Turn the turn signal bulb 1/4 turn counter clockwise Front Turn Signal to remove from housing. 1. Open the hood. 2. Remove the headlamp cover. 4. Disconnect the electrical connector and replace the bulb.
Page 354: Front Fog Light
354 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not touch the new bulb with your fingers. Oil Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
Page 355: Rear Tail, Stop, Turn Signal, And Back-Up
MAINTAINING YOUR VEHICLE 355 3. Squeeze the socket assembly tabs to remove it from the Rear Tail, Stop, Turn Signal, and Back-Up Lights housing. 1. Raise the liftgate. 2. Remove the two Torx fasteners. 4. Pull the bulb to remove it from the socket. 5.
Page 356: Center High Mounted Stop Light (Chmsl)
356 MAINTAINING YOUR VEHICLE Center High Mounted Stop Light (CHMSL) 2. Twist the bulb socket to remove from the CHMSL housing. 1. Remove the two screws securing the CHMSL. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
Page 357: Fluid Capacities
MAINTAINING YOUR VEHICLE 357 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 20.6 Gallons 78 Liters Engine Oil with Filter 3.7 Liter Engine (5W-30, API Certified) 5 Qts 4.7 Liters 4.7 Liter Engine (5W-30, API Certified) 6 Qts 5.7 Liters 5.7 Liter Engine (5W-20, API Certified) 7 Qts 6.6 Liters Cooling System *...
Page 358: Parts
358 MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil (3.7L/4.7L Engines) Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
Page 359: Chassis
MAINTAINING YOUR VEHICLE 359 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Mopar ATF+4 Automatic Transmission Fluid Transfer Case Mopar ATF+4 Automatic Transmission Fluid Axle Differential (Front-Rear) Mopar Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive. Brake Master Cylinder Mopar DOT 3 Brake Fluid, SAE J1703 should be used.
Page 361 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..362 Schedule “B” ......365 Maintenance Schedules .
Page 362: Emission Control System Maintenance
362 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The “Scheduled” maintenance services, listed in bold There are two maintenance schedules that show the type must be done at the times or mileages specified to required service for your vehicle. assure the continued proper functioning of the emission First is Schedule B .
Page 363 MAINTENANCE SCHEDULES 363 • Off-road or desert driving Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the • If equipped for and operated with E-85 (ethanol) interval that occurs first. fuel. NOTE: Most vehicles are operated under the conditions CAUTION! listed for Schedule “B.”...
Page 364 364 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the exhaust system. • Inspect the battery and clean and tighten the terminals •...
Page 365: Schedule "B
SCHEDULE “B” 365 • Off-road or desert driving Schedule “B” Follow this schedule if you usually operate your vehicle • If equipped for and operated with E-85 (ethanol) under one or more of the following conditions. fuel. • Day or night temperatures are below 32°F (0°C) NOTE: If ANY of these apply to you, change your •...
Page 366 366 SCHEDULE “B” Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 367 SCHEDULE “B” 367 Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 368 368 SCHEDULE “B” Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 369 SCHEDULE “B” 369 Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 370 370 SCHEDULE “B” Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) Drain and refill the front and rear axles. Drain and refill the automatic transmission fluid, and replace main sump filter (4.7L/5.7L Only).‡ Drain and refill the transfer case fluid.
Page 371 SCHEDULE “B” 371 Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (101 000) (106 000) (110 000) (115 000) (120 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 372 372 SCHEDULE “B” Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 373 SCHEDULE “B” 373 Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 374 374 SCHEDULE “B” Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect the engine air cleaner filter, replace if nec- essary.
Page 375 SCHEDULE “B” 375 Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Drain and refill the automatic transmission fluid, replace main sump filter, and spin-on cooler return filter (if equipped). (4.7L/5.7L Only).‡ Drain and refill the transfer case fluid.
Page 376: Schedule "A
376 SCHEDULE “A” Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [Months] [12] [18] [24] [30] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air cleaner filter, and replace if necessary.
Page 377 SCHEDULE “A” 377 Miles 36,000 42,000 48,000 54, 000 (Kilometers) (58 000) (67 000) (77 000) (86 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter. Rotate the tires. Inspect the brake linings. Lubricate the upper knuckle ball stud at steering & sus- pension ball joints.
Page 378 378 SCHEDULE “A” Miles 60,000 66,000 72,000 78,000 (Kilometers) (96 000) (106 000) (115 000) (125 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 379 SCHEDULE “A” 379 Miles 84,000 90,000 96,000 102, 000 (Kilometers) (134 000) (144 000) (154 000) (163 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 380 380 SCHEDULE “A” Miles 108,000 114,000 120,000 (Kilometers) (173 000) (182 000) (192 000) [Months] [108] [114] [120] Change the engine oil and engine oil filter. Rotate the tires. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary. Replace the spark plugs.
Page 381 SCHEDULE “A” 381 Inspection and service should also be performed anytime WARNING! a malfunction is observed or suspected. Retain all re- ceipts. You can be badly injured working on or around a motor vehicle. Do only that service work for which This maintenance is recommended by the manufac- you have the proper equipment.
Page 383: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Warranty Information ....386 Vehicle ......384 Mopar Parts .
Page 384: Suggestions For Obtaining Service For Your Vehicle
Warranty service must be done by an authorized Chrysler, Make a written list of your vehicle’s problems or the Dodge, or Jeep dealer. We strongly recommend that you specific work you want done. If you’ve had an accident, take your vehicle to you selling dealer. They know you...
Page 385 IF YOU NEED CONSUMER ASSISTANCE 385 This is why you should always talk to your dealer’s DaimlerChrysler Motors Corporation Customer Center service manager first. Most matters can be resolved with P.O. Box 21–8004 this process. Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 •...
Page 386: Warranty Information
386 IF YOU NEED CONSUMER ASSISTANCE Center. Any hearing or speech impaired customer who service contract that is not a manufacturer’s Service has access to a TDD or a conventional teletypewriter Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 387 IF YOU NEED CONSUMER ASSISTANCE 387 U.S. ONLY...
Page 388: Mopar Parts
388 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS To contact NHTSA, you may either call the Auto Safety Mopar fluids, lubricants, parts, and accessories are Hotline toll free at 1-800-424-9393 (or 366-0123 in Wash- available from your dealer. They will help you keep your ington DC area) or write to: NHTSA, U.S.
Page 389: Publication Order Forms
IF YOU NEED CONSUMER ASSISTANCE 389 • Diagnostic Procedure Manuals. PUBLICATION ORDER FORMS To order the following manuals, you may use either the Filled with diagrams, charts and detailed illustrations, website or the phone numbers listed below. Visa, Mas- these practical manuals make it easy for students and tercard, American Express, and Discover orders are ac- technicians to find and fix problems on computer- cepted.
Page 390 390 IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals...
Page 391 INDEX...
Page 392 392 INDEX ABS (Anti-Lock Brake) System ... . 165,246 Antenna, Satellite Radio ....210 Adding Washer Fluid .
Page 393 INDEX 393 Auxiliary Electrical Outlet ....148 Break-In Recommendations, New Vehicle ..63 Auxiliary Power Outlet ....148 Bulb Replacement .
Page 394 394 INDEX Catalytic Converter ..... . 321 Console, Overhead ..... . . 137 Caution, Exhaust Gas .
Page 395 INDEX 395 Data Recorder, Event ..... . 51 Drive Belts ......320 Daytime Running Lights .
Page 396 396 INDEX Engine Temperature Gauge ..... 167 Air Cleaner ......323 Engine Oil Viscosity .
Page 397 INDEX 397 Flooded Engine Starting ....231 Filler Door ......281 Fluid Capacities .
Page 398 398 INDEX Speedometer ......164 Holder, Cup ......149 Tachometer .
Page 399 INDEX 399 Interior Lights ..... . . 111,115 Lead Free Gasoline ..... . 277 Intermittent Wipers .
Page 400 400 INDEX Electronic Throttle Control Warning ..170 Rear Tail ......355 .
Page 401 INDEX 401 Lower Anchors and Tether for CHildren Automatic Dimming ..... 73 (LATCH) ......58,59 Electric Powered .
Page 402 402 INDEX Trip ....... . 168 Overheating, Engine ....168,297 Off-Pavement Driving .
Page 403 INDEX 403 Mirrors ......75 Rear Axle ......340 Outlet .
Page 404 404 INDEX Reminder, Seat Belt ..... . . 34 Satellite Radio Antenna ....210 Remote Keyless Entry .
Page 405 INDEX 405 Lumbar Support ..... . . 101 Signals, Turn ....116,164,353,355 Memory .
Page 406 406 INDEX Steering Wheel Mounted Sound System Tire and Loading Information Placard ..259,260 Controls ......211 Tire Identification Number (TIN) .
Page 407 INDEX 407 Safety ......65,254 Trailer and Tongue Weight ....285 Sizes .
Page 408 408 INDEX Vacuum/Vapor Harnesses ....334 Washing Vehicle ......341 Vanity Mirrors .

This manual is also suitable for:

2005 grand cherokee Grand cherokee

Jeep Automobile Owner's Manual

Quick Links

INTRODUCTION

Chapters

Related Manuals for Jeep Automobile

Summary of Contents for Jeep Automobile