Page 1
Type B, G, T Models Type B, G, T Models Type B, G, T Models For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Owner’s Guide and Installation Manual...
Fan ......13 use a solid-state speed control with this fan. Use only Hunter speed 10 •...
Page 3
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 42796-01 • 04/06/11 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing toward the ceiling peak. 42796-01 • 04/06/11 • Hunter Fan Company...
3-1. Unbundle the wires from the fan. Steps 3-2 – 3-3 Note: Your Hunter fan comes with an optional downrod extension Downrod pipe. If you are hanging the fan on a ceiling higher than 10 feet tall and you would like to use the enclosed optional downrod, follow Steps 3-9 3-13 on the next page.
Page 9
3-8. Raise the fan and place the hook on the ceiling plate through the U-shaped hole in the rim. Optional Downrod Instructions: Step 3-7 Your Hunter fan comes with an optional downrod extension pipe. If you would like to use the enclosed optional 6 inch U-shaped Hole downrod, follow the steps below.
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 42796-01 • 04/06/11 • Hunter Fan Company...
2. Press firmly on opposite sides of the ring toward the canopy. The tabs will flex out releasing the trim ring from the canopy. Step 5-3 Steps 5-4 – 5-5 Canopy Screw 42796-01 • 04/06/11 • Hunter Fan Company...
Blade Assembly they will damage the protective Dust Armor Screw on the blades. Grommet Blade Blade Iron Armature Screw (tighten securely) Shipping Bumper Blade Iron Blade Iron Armature Screws Step 6-3 42796-01 • 04/06/11 • Hunter Fan Company...
7-2. If you are using a downrod longer than 6 inches, leave the retaining screws in their place and continue the installation process. Notch Steps 7-1 – 7-2 Switch Housing Mounting Plate Red Retaining Screws 42796-01 • 04/06/11 • Hunter Fan Company...
Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch Plug Connector housing with three housing assembly screws. Note: You can customize your Hunter fan with a number of accessory light kits. Steps 8-5 – 8-6 Lower Switch...
If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 42796-01 • 04/06/11 • Hunter Fan Company...