Tuning Mode; Programmed Or - Toshiba Regza 52RV535U Owner's Manual

52RV535U ENbook Page 39 Tuesday July 22 2008 5:25 PM
Adding and clearing channels and inputs in the
History List
Adding channels and inputs to the History List:
As a channel or input is tuned, the Channel Browser _''
adds it to the History List and displays it on the "right
side" of the Channel Browser_'L Previously tuned
channels/inputs are "shifted" to the left, eventually
moving off the left side. Press _ • to surf backward
through the previously tuned charulels/inputs. Any
channel or input that is tuned repeatedly will not be
repeated in the History List but instead will be moved to
the end of the list on the right side of the Channel
growser_'L
The Charulel Browser _'' will store the following channels:
• All channels that are tuned using the numeric buttons
on the remote control.
• All channels that are tuned for at least 5 seconds using
(_) or _ on the remote control.
Note: Whenever an item is selected that cannot be tuned (for
various reasons), the TV will automatically tune to the
previously viewed channel or inpuL
Clearing channels from the History List:
• Reconfiguring the ANT/CABLE input will clear the
History List.
Note: See page 30 for details on configuring the antenna
inpuL
• Once 32 channels or inputs are stored in the History
List, the oldest item will be removed from the list
when a new channel or input is tuned.
• Turning off the TV will clear the History List.
Setting the Channel Tuning Mode
This feature allows you to choose how tuning will be
handled for analog and digital channels when the TV is
in Anterula mode.
Note:
77) use this feature, the Input
Configuration
must be set
to Antenna (_' page 30)_
The channel tuning mode has three options.
Standard
Auto
(default)
Digital
Both analog and digital channels can be
tuned normally
Digital channels will have priority when
manually enterin_ a channel number
using the Channel Number (0-9) on the
remote control, analog charulels can still
be tuned by _z_ / _ if available
Only digital channels can be tuned
Note: Digital mode will be most useful after analog channels
are shut down by the government in 2009_
To set the Channel Tuning Mode:
1
From the
Setup
menu, highlight
Installation
and
press @. A new set of Installation menu icons will
appear.
2 Open the Terrestrial menu, highlight Channel
Tuning Node, press • and • • to select your
desired mode, and then press @.
Note:
• The ChannelAdd/Delete & Channels Block w177dews as well
as the Channel Browser ANZTCABLE list will be updated
automatically when you change the mode. Also, the History
List will be cleared, but the Favorites List will be saved.
• Even if the Channel Rming Mode is set to Digital, analog
channel 3 will still be the default channel to prevent the initial
case where no digital channels have been found in prior
channel scans. (Channel Add/Delete will net have anything
listed until a scan is donee)
Tuningto the next programmedchannel
To tune to the next programmed channel:
Press _,) or _ on the remote control or TV control panel.
Note:This feature will not work unless you program channels
i)_tethe TV's channel memory (_ page 30)_
Tuningto a specific channel (programmed
or unprogrammed)
Tuning analog channels:
Press the Channel Number (0-9) on the remote control.
For example, to select channel 125, press 1, 2, 5, then @.
Tuning digital channels:
Enter the major Channel Number (0-9) on the remote
control, followed by the dash ((_)) button and then the
sub-channel number. For example, to select digital
channel 125-1, press 1, 2, 5, -, 1, then @.
Note: If a digital channel is not programme_either through
the automatic channel scan (_ page 30) or the channel add/
delete function (_ page 31) you will have to tune the RF
channel using the Physical Channel Number.
(continued)
30
RV535U (E/F) Web 213:276