Table of Contents
Advertisement
Quick Links
Safety Instructions
& Operator's
Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 1
MODELS
NZMJ23521KH
NZMJ25611KH
MODEL
NUMBER
EXPLANATION
INI;
MODEL DESIGNATION ._1
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP
: I_JI _31_zl , I KHI
I
ENGINE TYPE
SERIES DESIGNATION
MOWER DECK SIZE
POWER
UNIT
N - Model Designation
23 - Engine Horse Power
1 - Series Designation
KH - Kohler Engine
Z -Zero
Turning - Hydro Drive
25-
Engine Horse Power
M - Mid Mount Mower
52 - 52" Mower Width
J - Joystick Control
61 - 61" Mower Width
Thank you for buying a SNAPPER Product!
Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT
SAFETY INSTRUCTIONS"
on Pages 2 - 4.
Remember that all power
equipment
can be dangerous
if used improperly.
Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
COPYRIGHT
© 2003
SNAPPER
PRODUCTS
INC
ALL RIGHTS
RESERVED
SNAPPER McOooouoh
GA., 30253
U.S.A.
MANUAL No. 7-5593 (Rev I, 8/5/03)
Advertisement
Table of Contents
Related Manuals for Snapper NZMJ23521KH
Summary of Contents for Snapper NZMJ23521KH
- Page 1 M - Mid Mount Mower 52 - 52" Mower Width J - Joystick Control 61 - 61" Mower Width Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay particular attention to the "IMPORTANT SAFETY INSTRUCTIONS"...
-
Page 2: Section 1 - Familiarization
DEFLECTOR, DECK LIFT PEDAL differ from your specific model. Contact your Snapper dealer if you have questions 1.1 INTRODUCTION 1.2 NOMENCLATURE nomenclature information above shows This manual has been prepared for the operator's of... -
Page 3: Section 2 - Safety Messages And Symbols
Section 2 - SAFETY MESSAGES AND SYMBOLS REVERSE DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS MOTION CONTROLLEVER(JOYSTICK) MULT-D RECT ONAL I PARKING BRAKE LEVER OPERATION I I WEARHEAR'NGPROTECT'ON TO O_F._AT TO gT_z O_ %_ _ F_A_ _ _E_E U_¸... -
Page 4: Section 3 - Operating
Section 3 - OPERATING INSTRUCTIONS PRE-START CHECK LIST 3,1,8. Place mower desired cutting height Make the following checks and perform the service setting. Grasp deck lift lever and depress release latch located underneath the lever. Move lever to required before each start-up. 3.1.1. - Page 5 Section 3 - OPERATING INSTRUCTIONS ROLL RELEASE: To roll the machine without the STARTING & STOPPING - ENGINE, BLADES, engine running, pressure within the hydraulic pumps PARKING BRAKE must be released, There is a hydraulic pressure relief This machine is equipped with dual hydraulic pumps and valve on the upper side of each pump that is used to wheel drive motors.
-
Page 6: Cutting Height Adjustment
Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. -
Page 7: Stopping Machine
Perform the following interlock system checks position periodically during the operating season. Contact your authorized Snapper dealer if you have questions. WARNING DO NOT operate machine if any safety interlock or safety... -
Page 8: Section 4 - Maintenance
Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BELT 4. Clean Mower Deck 1. Lower deck to lowest setting. a. Remove key from ignition switch. 2. Remove footrest. See Figure 4.3. b. Remove spark plug wire(s) and secure away 3. Removal of footrest will allow access to deck from spark plug(s). -
Page 9: Deck Removal
Section 4 - MAINTENANCE 4.6 DECK REMOVAL WARN ING Move power unit/mower deck to an area where the mower deck is to be disconnected. Turn engine Allow engine to cool for at least ten minutes before "OFF" and remove key from switch. Remove spark performing service or maintenance. -
Page 10: Neutral Position Adjustments
Section 5 - ADJUSTMENTS & REPAIR DANGER REMOVE MOTION CONTROL this I Exercise EXTREME CAUTION when making LEVER CONNECTING adjustment, due to close proximity of moving parts. NEUTRAL POSITION ADJUSTMENTS The motion control lever controls the movement and stopping of the machine. Move the control lever to the center or neutral... -
Page 11: Section 5 - Adjustments
Section 5 - ADJUSTMENTS & REPAIR Battery Condition Chart State of Charge Syringe Hydrometer Digital Voltmeter Five Ball Hydrometer 1.280 12.80v 100% Charged w/Sulfate Stop Five Balls Floating 1.265 12.60v 100% Charged Four Balls Floating 1.210 12.40v 75% Charged Three Balls Floating 1.160 12.10v 50% Charged... -
Page 12: Primary Maintenance
PRIMARY MAINTENANCE illustration how dirt can dama & how naintenance can protect it! Snapper uses the best avail- able engines and components In their products In order to provide long, satisfactory service. However, proper • = care Is essential In ""... - Page 13 NOTES...
- Page 14 Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings.