Snapper NZM19482KWV Safety Instructions & Operator's Manual
Mid mount z-rider zero turning hydro drive 2 series
Hide thumbs
Also See for NZM19482KWV:
- Safety instructions & operator's manual (40 pages) ,
- Parts manual (84 pages)
Table of Contents
Advertisement
Quick Links
Safety Instructions
& Operator's
Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 2
MODELS
NZM19482KWV
NZM21522KWV
NZM25612KWV
NZM27 612KH
MODEL
NUMBER
EXPLANATION
INI
;
MODEL DESIGNATION ._1
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP *
:1 I1 I 1_1431 :
! I KWVl
I
ENGINE TYPE
SERIES DESIGNATION
MOWER DECK SIZE
POWER
UNIT
19.0 - Engine Horse Power
21.0 -- Engine Horse Power
25.0 - Engine Horse Power
27.0 - Engine Horse Power
N - Model Designation
48 - 48" Mower Width
2 - Series Designation
Z - Zero Turning - Hydro Drive
52 - 52" Mower Width
KW - Kawasaki Engine
M - Mid Mount Mower
61 - 61" Mower Width
KH - Kohler Engine
V - Over Head Valve
Thank you for buying a SNAPPER Product!
Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT
SAFETY INSTRUCTIONS"
on Pages 2 - 4.
Remember that all power
equipment
can be dangerous
if used improperly.
Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
NOTE: Specifications
are correct
at time of printing and are subject
to change without
notice.
* Actual sustained
equipment
horsepower will likely be lower due to operating limitations and environmental
factors.
COPYRIGHT
CU2004
SNAPPER .coo°ough,
OA.,
SNAPPER
A DIVISION
OF SIMPLICITY
MFG
INC
ALL RIGHTS
RESERVED
MANUAL No. 7-4408 (Rev. I - 9/3/04)
Advertisement
Table of Contents
Related Manuals for Snapper NZM19482KWV
Summary of Contents for Snapper NZM19482KWV
- Page 1 61 - 61" Mower Width KH - Kohler Engine V - Over Head Valve 27.0 - Engine Horse Power Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay particular attention to the "IMPORTANT SAFETY INSTRUCTIONS"...
- Page 2 Operator Protective Structures may be required by local ordinances. Discuss your mowing application and ordinances with your local Snapper Dealer.
-
Page 3: Section 2 -Safety Messages And Symbols
Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS I MOTION CONTROL LEVER OPERATION I PARKING BRAKE LEVER OPERATION I I WEARHEAR'NGPROTECT'ON TO O_F._AT TO gT_z O_ %_ _ F_A_ _ _E_E U_¸ STARTING, OPERATION WARNING ! AVOID SERIOUS INJURY OR DEATH &... - Page 4 Section 3 - OPERATING INSTRUCTIONS PRE-START CHECK LIST 3,1,8. Place mower desired cutting height Make the following checks and perform the service setting. Grasp deck lift lever and depress release latch located underneath the lever. Move lever to required before each start-up. 3.1.1.
-
Page 5: Cutting Height Adjustment
Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. -
Page 6: Safety Interlock System Check
Perform the following interlock system checks position & the neutral lock position. periodically during the operating season. Contact your authorized Snapper dealer if you have questions. WARNING DO NOT operate machine if any safety interlock or... -
Page 7: Deck Removal
Section 4 - MAINTENANCE 4.6 DECK REMOVAL WARN ING Move power unit/mower deck to an area where the mower deck is to be disconnected. Turn engine Allow engine to cool for at least ten minutes before "OFF" and remove key from switch. Remove spark performing service or maintenance. - Page 8 Section 5 - ADJUSTMENTS & REPAIR NEUTRAL POSITION ADJUSTMENTS MOWER DECK & COMPONENT ADJUSTMENTS (Continued From Previous Page) The leveling procedures for the 61 deck differ from 12, With motion control levers remaining in the the 48 and 52 decks. The 61 deck replaces the two neutral lock position, See Figure 3.7, hold connecting rear eyebolts with slotted brackets_ and uses 1 1/4"...
-
Page 9: Battery Testing
Section 5 - ADJUSTMENTS & REPAIR 5.10.4, BATTERY TESTING 1. Remove battery. Refer to Section "BATTERY WARNING REMOVAL". 2.Using a voltmeter, check the battery_s state of DO NOT attempt to service or charge the battery I charge by comparing the voltmeter reading with while it is installed in the machine. -
Page 10: Troubleshooting
2. Replace fuse. 3. Electrical connections loose or corroded. 3. Clean and check connections for good contact. 4. Defective ignition switch. 4. Contact authorized SNAPPER dealer. Engine Will Not Start 1. Blade engagement switch in the "ON" position. 1. Move blade engagement switch to "OFF".