Table of Contents
Advertisement
Safety Instructions
& Operator's
Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 1
MODELS
NZM19481KWV
NZM21521KWV
NZM25611KWV
NZM27611KH
MODEL
NUMBER
EXPLANATION
INI
;
MODEL DESIGNATION ._1
DRIVE SYSTEM TYPE
MOWER ORIENTATION
ENGINE HP
: I 1111_1431 '
, I KWVl
J
ENGINE TYPE
SERIES DESIGNATION
MOWER DECK SIZE
POWER
UNIT
19.0 - Engine Horse Power
21.0 -- Engine Horse Power
25.0 - Engine Horse Power
27.0 - Engine Horse Power
N - Model Designation
48 - 48" Mower Width
1 - Series Designation
Z - Zero Turning - Hydro Drive
52 - 52" Mower Width
KW - Kawasaki Engine
M - Mid Mount Mower
61 - 61" Mower Width
KH - Kohler Engine
V - Over Head Valve
Thank you for buying a SNAPPER Product!
Before operating your machine, read this manual carefully and pay
particular attention to the "IMPORTANT
SAFETY INSTRUCTIONS"
on Pages 2 - 4.
Remember that all power
equipment
can be dangerous
if used improperly.
Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense!
SNAPPER McOo°ouo.
COPYRIGHT
© 2003
SNAPPER
PRODUCTS
INC
GA., 30253
U.S.A.
ALL RIGHTS
RESERVED
MANUAL No. 7-1762 (I.R. 11/25/03)
Advertisement
Table of Contents
Related Manuals for Snapper NZM27611KH SERIES 1
Summary of Contents for Snapper NZM27611KH SERIES 1
- Page 1 61 - 61" Mower Width KH - Kohler Engine V - Over Head Valve 27.0 - Engine Horse Power Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay particular attention to the "IMPORTANT SAFETY INSTRUCTIONS"...
-
Page 2: Section 1 - Familiarization
DISCHARGE are provided for reference only and may DEFLECTOR, differ from your specific model. Contact DECK LIFT PEDAL your Snapper dealer if you have questions FIGURE 1.1 INTRODUCTION 1.2 NOMENCLATURE nomenclature information above, Figure 1.1, This manual has been prepared for the operator's of... -
Page 3: Section 2 - Safety Messages And Symbols
Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS I MOTION CONTROL LEVER OPERATION I PARKING BRAKE LEVER OPERATION I I WEARHEAR'NGPROTECT'ON TO O_F._AT TO gT_z O_ %_ _ F_A_ _ _E_E U_¸ STARTING, OPERATION WARNING ! AVOID SERIOUS INJURY OR DEATH &... - Page 4 Section 2 - SAFETY MESSAGES AND SYMBOLS _ T _ OFF/STOP START PULL SWITCH "UP" TO ENGAGE BLADES PUSH SWITCH "DOWN" HOUR METER DISENGAGE BLADES KEYSWITCH SLOW I CONTROL PANEL IDENTIFICATION CHOKE CONTROL ENGINE SPEED CONTROL KEEP CHILDREN AND OTHERS OUT OF MOWING AREA DANGER! ROTATING BLADES STOP...
-
Page 5: Section 3 - Operating
Section 3 - OPERATING INSTRUCTIONS ROLL RELEASE: To roll the machine without the STARTING & STOPPING - ENGINE, BLADES, engine running, pressure within the hydraulic pumps PARKING BRAKE must be released, There is a hydraulic pressure relief This machine is equipped with dual hydrostatic wheel valve on the upper side of each pump that is used to drive transmissions. - Page 6 7 seconds, the electric clutch should be checked. Adjustment or replacement of electric clutch may be necessary. Return the machine to an FIGURE 3.8 authorized Snapper dealer replacement. NOT CONTINUE to operate mower if blades fail to WARN ING stop in 7 seconds.
-
Page 7: Cutting Height Adjustment
Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. -
Page 8: Safety Interlock System Checks
Perform the following interlock system checks position & the neutral Iock position. periodically during the operating season. Contact your authorized Snapper dealer if you have questions. WARNING DO NOT operate machine if any safety interlock or... -
Page 9: Section 4 - Maintenance
Section 4 - MAINTENANCE HYDRAULIC FLUID RESERVOIRS 4,3.3. RIDING MOWER - LUBRICATION 1, Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. WHEEL FIGURE 4.6 LUBRICATE BEARINGS FIGURE 4.5 2. -
Page 10: Deck Removal
Section 4 - MAINTENANCE 4.6 DECK REMOVAL WARN ING Move power unit/mower deck to an area where the mower deck is to be disconnected. Turn engine Allow engine to cool for at least ten minutes before "OFF" and remove key from switch. Remove spark performing service or maintenance. -
Page 11: Section 5 - Adjustments
Section 5 - ADJUSTMENTS & REPAIR UNHOOK TRACTION REMOVEANTI- WARNING DRIVE IDLER SPRING ROTATION BRACKET DO NOT attempt any maintenance, adjustments service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. - Page 12 Section 5 - ADJUSTMENTS & REPAIR WARNING RED (POSITIVE) CABLE _ATIVE) CABLE Shield positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must connected battery terminals in the proper position.
- Page 13 Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings.