Cycles - Whirlpool duet WFW9451XW00 Use & Care Manual

To lock the controls
Press and hold CONTROLS LOCK/UNLOCK for 3 seconds.
®
Controls L ock/Unlock
Holdfor 3 Seconds
The status light next to the CONTROLS LOCK/UNLOCK button
will glow.
To unlock the controls
Press and hold CONTROLS LOCK/UNLOCK for 3 seconds until
the status light turns off.
NOTE: To lock or unlock the controls when the washer is off,
press and hold CONTROLS LOCK/UNLOCK for 3 seconds.
Door Locked
When the status light glows, the door is locked.
Sensing/Revising Estimated Time
The cycle times vary automatically based on your water pressure,
water temperature, detergent, and clothes load.
The washer will automatically sense the progress in the cycle and
adjust the Estimated Time Remaining display. While the washer is
sensing, the estimated time will flash and the Sensing Status
Light will glow. When the sensing is complete, the flashing stops,
the status light goes off and the Estimated Time Remaining
display is updated.
The cycle time will be extended if oversudsing occurs or the load
is unbalanced. The SUD routine removes extra suds and assures
proper rinsing of your garments. See "Troubleshooting." During
the unbalance routine the time displayed may pause until this
activity is complete, then resume with the remainder of the cycle.
Cycles
Cycles can be selected by turning the Cycle Control knob to the
desired cycle. Each cycle is designed for different types of fabric
and soil levels. The Modifier Indicator Lights, on the right-hand
side of the panel, will change as cycles are selected.
NORMAL
HAND DELICAT BULKY ITEMS
WASHABLES HEAVY DUTY
QUICK WASH WHITEST
was. cYc_s WHITES
SANITARY
RINSE/SPIN
CLEAN W ASHER SOAK
Each cycle has a preset Soil Level (estimated cycle time),
Water Temp, and Spin Speed, and may have preset options.
The preset settings provide the recommended fabric care for
the selected cycle.
The preset settings will glow green to show the preselected
Options and Modifiers, and be changed anytime before
START is pressed. Not all Options and Modifiers are available
with all cycles. Available selections glow amber. (To change
settings after the cycle has started, press PAUSE/CANCEL
once, then select the desired settings. Press START to
continue the cycle.)
Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent in slow-speed
cycles.
Preset cycle settings
Each cycle has a preset Soil Level (cycle time), Water Temp, and
Spin Speed. The preset settings provide the recommended fabric
care for the selected cycle. See chart.
Cycle Soil Level Water Temp Spin
(cycle time) Speed
Sanitary Normal Super Hot/Cold High
(1:50)
Whitest Normal Hot/Cold High
Whites (1:15)
Heavy Duty Heavy Warm/Cold High
(1:20)
Bulky Items Heavy Warm/Cold High
(1:05)
Normal/ Normal Warm/Cold High
Casual (0:50)
Delicate Normal Warm/Cold Medium
(0:40)
Hand Normal Cold/Cold Low
Washables (0:30)
Quick Wash Light Warm/Cold High
(2-3 Items) (0:18)
Clean N/A N/A N/A
Washer (0:46)
with
AFFRESH ®
Soak Normal Warm/Cold N/A
(0:32)
Rinse/Spin N/A Cold/Cold High
(0:22)
Drain/Spin N/A N/A High
(0:13)
To change the preset cycle settings
Press the selector of each available setting until the desired
setting glows green.
Sanitary
The Sanitary cycle is certified by NSF International, an
independent, third party testing and certification organization.
The certification verifies that the Sanitary cycle eliminates
99.9% of bacteria typically found on clothing, bedding, and
towels. There is no carryover of bacteria between loads after
the cycle is complete.
Use this cycle to clean heavily soiled, colorfast fabrics. This
combines a super hot water temperature and high-speed tumbling
to help ensure the removal of heavy soils and stains. It is
recommended that you set your hot water heater to 120°F (49°C)
to ensure proper performance during this cycle.
Only the Sanitary cycle has been designed to meet the
requirements of NSF Protocol P172 Sanitization Performance
of Residential and Commercial, family sized clothes washer.
14