Dell Broadcom NetXtreme Family of Adapters User Manual page 86

iSCSI Protocol: Broadcom NetXtreme II Network Adapter User Guide
Q: Why does the install fail when attempting to complete an iSCSI offload install using Windows Server 2008 R2 for BCM5709
(1 GbE) adapters?
A: There is a conflict with the internal inbox driver.
Event Log Messages
Table 5 lists the offload iSCSI driver event log messages.
Offload iSCSI (OIS) Driver
Table 5: Offload iSCSI (OIS) Driver Event Log Messages
Message
Severity
Number
1 Error
2 Error
3 Error
4 Error
5 Error
6 Error
7 Error
8 Error
9 Error
10 Error
11 Error
12 Error
13 Error
14 Error
15 Error
16 Error
17 Error
18 Error
19 Error
20 Error
21 Error
22 Error
23 Error
24 Error
25 Error
26 Error
27 Error
28 Error
file:///T|/htdocs/NETWORK/BroadCom/71921/NetXtremeII/en/iscsi.htm[9/26/2012 3:29:03 PM]
Message
Initiator failed to connect to the target. Target IP address and TCP Port number are given in dump
data.
The initiator could not allocate resources for an iSCSI session.
Maximum command sequence number is not serially greater than expected command sequence
number in login response. Dump data contains Expected Command Sequence number followed by
Maximum Command Sequence number.
MaxBurstLength is not serially greater than FirstBurstLength. Dump data contains FirstBurstLength
followed by MaxBurstLength.
Failed to setup initiator portal. Error status is given in the dump data.
The initiator could not allocate resources for an iSCSI connection
The initiator could not send an iSCSI PDU. Error status is given in the dump data.
Target or discovery service did not respond in time for an iSCSI request sent by the initiator. iSCSI
Function code is given in the dump data. For details about iSCSI Function code please refer to iSCSI
User's Guide.
Target did not respond in time for a SCSI request. The CDB is given in the dump data.
Login request failed. The login response packet is given in the dump data.
Target returned an invalid login response packet. The login response packet is given in the dump
data.
Target provided invalid data for login redirect. Dump data contains the data returned by the target.
Target offered an unknown AuthMethod. Dump data contains the data returned by the target.
Target offered an unknown digest algorithm for CHAP. Dump data contains the data returned by the
target.
CHAP challenge given by the target contains invalid characters. Dump data contains the challenge
given.
An invalid key was received during CHAP negotiation. The key=value pair is given in the dump data.
CHAP Response given by the target did not match the expected one. Dump data contains the CHAP
response.
Header Digest is required by the initiator, but target did not offer it.
Data Digest is required by the initiator, but target did not offer it.
Connection to the target was lost. The initiator will attempt to retry the connection.
Data Segment Length given in the header exceeds MaxRecvDataSegmentLength declared by the
target.
Header digest error was detected for the given PDU. Dump data contains the header and digest.
Target sent an invalid iSCSI PDU. Dump data contains the entire iSCSI header.
Target sent an iSCSI PDU with an invalid opcode. Dump data contains the entire iSCSI header.
Data digest error was detected. Dump data contains the calculated checksum followed by the given
checksum.
Target trying to send more data than requested by the initiator.
Initiator could not find a match for the initiator task tag in the received PDU. Dump data contains the
entire iSCSI header.
Initiator received an invalid R2T packet. Dump data contains the entire iSCSI header.