EverFocus Color Rugged Dome Camera EHD350 Operation Instructions Manual
1/3” 560 tvl high resolution color rugged dome camera
Hide thumbs
Also See for Color Rugged Dome Camera EHD350:
- Specifications (14 pages) ,
- Quick reference manual (4 pages) ,
- Quick reference manual (4 pages)
Advertisement
Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1.
Do not install the camera near electric or magnetic fields.
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices will distort the video
images.
2.
Never disassemble the camera nor put impurities in it.
Disassembly or impurities may result in trouble or fire.
3.
Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
4.
Keep the power cord away from water and liquid.
Touching the wet power cord may result in electric shock.
5.
Never install the camera in areas exposed to water, oil or gas.
Water, oil or gas may result in failure, electric shock or fire.
6.
Cleaning
Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from
EVERFOCUS
1/3" 560 TVL High Resolution
Color Rugged Dome Camera
Operation Instructions
Model No.
EHD350
Advertisement
Table of Contents
Related Manuals for EverFocus Color Rugged Dome Camera EHD350
Summary of Contents for EverFocus Color Rugged Dome Camera EHD350
-
Page 1: Operation Instructions
Water, oil or gas may result in failure, electric shock or fire. Cleaning Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from EVERFOCUS 1/3” 560 TVL High Resolution Color Rugged Dome Camera... -
Page 2: Package Contents
The most technically advanced EHD series are the newest vandal-resistant Color Rugged Dome Camera from EverFocus Electronics. The Color Rugged Dome Camera can withstand a blow from a 10-pound sledgehammer and has a built-in heater that allows for operation in low temperatures. -
Page 3: Specifications
Desiccant Pack x 1 Manual x 1 Optional Accessory Wall Mount Bracket (BA-EHD) SPECIFICATIONS Pickup Device Video Format Scanning System Picture Elements Horizontal Resolution Sensitivity S/N Ratio Electronic Shutter Lens Type Back Light Comp. Auto Gain Control Flickerless Auto White Balance Gamma Correction Video Output Sync. -
Page 4: Installation
Dimensions Weight Operating Temperature Certifications FCC/CE DIMENSIONS INSTALLATION 1. Loosen the 4 fix screws on the housing cover by using the attached wrench (Figure 1). Carefully uncap the housing cover as the direction shown below (Figure 2), please pay attention not to damage the lens. To remove the housing cover, push the hinges to the bottom of the bracket, the hinges can be easily removed from the bracket. - Page 5 2. Remove the camera. Vari-Focal Lens Heater Locking Screws Figure 3 To remove the camera, first unplug the wire connection on the back of the camera. Then loosen the 2 locking screws on the camera base, push the camera base to the right (toward heater direction, as shown in Figure 3), remove the camera from the mounting base.
- Page 6 Attach the base to the wall or ceiling, fix the base by the 4 setscrews attached in the accessory pack. The dome is weighted 1.7kg, please make sure if the mounting is strengthened enough to support it, if not, please reinforce the mounting according to the environment.
- Page 7 4. Re-assemble Camera When mounting COLOR RUGGED DOME CAMERA on the wall, please aim the “Wall” in line with the triangle “ ” marked on the lead frame. (Factory default) Figure 6-1 When mounting COLOR RUGGED DOME CAMERA on the ceiling, please aim the “Ceiling”...
- Page 8 5. Wire Connection Termination Board Micro Switch for Alarm trigger Power In Alarm COM Video Power In Alarm NO V. Phase Adjustment VR Alarm NC Figure 7 Connect the power supply cable (AC24V/DC12V), video output and alarm output to the proper connectors shown as Figure 7. The V.
- Page 9 6. View Angle Adjustment The camera can be rotated 360° horizontally, 140° vertically and 60° 3’rd axis view angles (as shown in Figure 8). Adjust the proper camera view angle as needed. If a vari-focal lens is used, you may adjust the focus and zoom of the lens to bring the object in focus.
-
Page 10: Dip Switch Function
DIP SWITCH FUNCTION LL (Line-Lock) OFF/ON To select the sync mode between Internal Sync.(LL off) and Line-Lock (LL on). Set the line-lock off, the camera will synchronize to the internal time base. Set the line-lock ON, the camera’s vertical synchronization can be driven by the AC signal in the power lines. - Page 11 BLC (Back Light Compensation) ON/OFF When BLC is turned on, the AGC, ES and IRIS operating points are determined by averaging over the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area can be clearly distinguished from brightly-lit backgrounds.
-
Page 12: Simple Instructions For The Desiccant Pack
SIMPLE INSTRUCTIONS FOR THE DESICCANT PACK Due to the camera lens blurred from the humidity inside the camera. The desiccant pack absorbs the humidity; please refer to the easy instruction as follows: 1. Adjust all settings first and place the desiccant pack on the horizontal rod, then bend the horizontal rod and fix it. - Page 13 415 Oser Avenue Unit S Hauppauge, NY 11788 TEL: 631-436-5070 FAX: 631-436-5027 www.everfocus.com Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.