Indoor color mini dome camera, outdoor day/night 3-axis vandal dome camera, outdoor color 3-axis vandal dome camera, outdoor day/night ir 3-axis vandal dome camera, outdoor day/night mini bullet, indoor color non-functioning side view smoke detector camer (14 pages)
EVERFOCUS 1/3” Color Rugged Dome Camera Operation Instructions EHD300 Model No. Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice.
Page 2
The most technically advanced EHD series are the newest vandal-resistant Color Rugged Dome Camera from EverFocus Electronics. The Color Rugged Dome Camera can withstand a blow from a 10-pound sledgehammer and has a built-in heater that allows for operation in low temperatures.
INSTALLATION 1. Loosen the 4 fix screws on the housing cover by using the attached wrench (Figure 1). Please pay attention not to damage the lens. Figure 1 2. Remove the camera. Vari-Focal Lens Locking Screws Figure 2 To remove the camera, first unplug the wire connection on the back of the camera. Then loosen the 2 locking screws on the camera base, push the camera base to the right (toward heater direction, as shown in Figure 2), remove the camera from the mounting base.
Page 4
3. Mounting the base. Side conduit entry Conduit plug setscrew Back conduit entry Mounting Setscrew Mounting Setscrew Mounting Setscrew Mounting Setscrew Figure 3 Attach the base to the wall or ceiling, fix the base by the 4 setscrews attached in the accessory pack.
Page 5
Back conduit entry (PF1/2) The camera comes with a conduit plug pre-installed in the PF 1/2 conduit entry on the side. The screw can be removed and installed in the back conduit entry. Loosen the conduit plug setscrew (as shown in Conduit plug Figure 4) before removing the conduit plug.
Page 6
Micro Switch for Alarm trigger Power In Alarm COM Video Power In Alarm NO V. Phase Adjustment VR Alarm NC Figure 5 Connect the power supply cable (12VDC/24VAC), video output and alarm output to the proper connectors shown as Figure 5. The V.
DIP SWITCH FUNCTION Vari-Focal Lens FL (Flickerless Function) ON/OFF When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic shutter at 1/100(NTSC) or 1/120(PAL) automatically, and reduce the flicker immediately. The default setting is OFF. Mirror ON/OFF Mirror ON: Set a horizontal image inversion.
Page 9
D/N OFF: Camera stays in color mode. Note: when AGC setting is OFF, then D/N function will be inactive. The default setting is OFF. IRIS Level Adjustment Brightness Level can be adjusted from the IRIS level VR. Turn counterclockwise to L to get darker picture. ...
SIMPLE INSTRUCTIONS FOR THE DESICCANT PACK Due to the camera lens blurred from the humidity inside the camera. The desiccant pack absorbs the humidity; please refer to the easy instruction as follows: 1. Adjust all settings first and place the desiccant pack on the horizontal rod, then bend the horizontal rod and fix it.
SPECIFICATIONS Pickup Device 1/3'' SONY Super HAD CCD Video Format NTSC or PAL NTSC: 525 TV lines, 60 fields/sec. Scanning System PAL: 625 TV lines, 50 fields/sec. Picture Elements 768 x 494(NTSC) ; 752 x 582(PAL) Horizontal Resolution 520TVL Sensitivity 0.4Lux/F=1.2 S/N Ratio Over 48dB (AGC off)
Page 12
CONTENT LIST Standard Accessories 1. Camera Unit 2. Operation Instruction (this document) 3. Accessory Pack 4. Waterproof Connector 5. Power & Video Cable Optional Accessory 1. Wall Mount Bracket (BA-EHD)
Page 13
Housefin Bhavan, C-21 Bandra Kurla Complex, Bandra (East), Mumbai 400 051 Tel: +91 22 6128-8700 Your EverFocus product is designed and Ihr EverFocus Produkt wurde entwickelt und manufactured with high quality materials and hergestellt mit qualitativ hochwertigen components which can be recycled and Materialien und Komponenten, die recycelt reused.