Panasonic OneHome BB-HCM311A Operating Instructions Manual
Camera integration note
Hide thumbs
Also See for OneHome BB-HCM311A:
- Operating instructions manual (154 pages) ,
- Installation/troubleshooting manual (60 pages) ,
- Operating instructions manual (146 pages)
Advertisement
Quick Links
OneHome
Manufacturer:
Model Number(s):
OneHome Versions:
Comments:
Document Revision Date:
O
S
VERVIEW AND
UPPORTED
Installing the Panasonic camera can be broken down into the following steps:
1. Install cameras at desired locations, and pull power and Cat5 cabling as needed. Refer to the
Panasonic documentation for mounting details.
2. Connect the cameras electrically to the home network and configure the cameras. See Camera
Configuration.
3. Integrate the cameras into the OneHome system and test proper operation. This step is outlined
in HomeLogic Configuration Details.
T
HESE CAMERAS SUPPORT THE FOLLOWING FEATURES
Pan / Tilt: The camera can be turned to see various locations.
Built-in Audio: There is a built-in microphone as well as a jack for an external microphone. Audio from
the Panasonic cameras is supported in version 4.0 and later.
Presets: Some of these camera models also support presets, allowing the user to store predefined
locations such as a driveway or pool. This feature requires OneHome software version 4.0 or later.
C
C
AMERA
ONFIGURATION
The camera configuration is done with software provided by Panasonic, which must be run from a
computer with Windows also connected to the same network as the camera.
The software program from Panasonic is EasyConfig.exe: the version we checked is shown at the top.
I
N
MPORTANT
OTES
1. Cameras must be configured one at a time: If you are installing more than one camera, setup
the first one completely before powering up subsequent cameras.
2. Setup the camera within 20 minutes: Initial settings must be made within 20 minutes of the
camera being turned on. If the camera has been powered up for more than 20 minutes, cycle
power to the camera before proceeding.
3. DON'T LOSE THE CAMERA PASSWORD: During setup you will create a user name and
password, which are required to make any other changes in the future. If you lose the user name
or password you will have to factory reset the camera and repeat this entire procedure.
4. DEFAULT USER NAME / PASSWORD: For Panasonic cameras, our default user name is
Administrator and our default password is password.
HomeLogic LLC
Panasonic
BB-HCM311A, BB-HCM331A, KX-HCM110A
3.0 (all builds), 4.0 (all builds)
Network Camera (EasyConfig.exe version 1.0.21)
9/6/2006
F
EATURES
100 Hoods Lane
Marblehead, MA 09145
Camera Integration Note
:
Phone (781) 639-5155
Fax (781) 639-9677
Advertisement
Related Manuals for Panasonic OneHome BB-HCM311A
Summary of Contents for Panasonic OneHome BB-HCM311A
- Page 1 AMERA ONFIGURATION The camera configuration is done with software provided by Panasonic, which must be run from a computer with Windows also connected to the same network as the camera. The software program from Panasonic is EasyConfig.exe: the version we checked is shown at the top.
- Page 2 TARTING THE ANASONIC AMERA OFTWARE 1. Insert the CD from the camera into your PC: once it starts up, click Camera Setup. Or, if you have copied the files from the CD to your computer, locate and start EasyConfig.exe. 2. Wait a moment to allow the software to find the camera: the following screen appears. 3.
- Page 3 6. You will be prompted to enter your user name and password again, as shown in the image below. Type in the user name and password you just set, and click OK. 7. After a short delay, you should see a new browser window, similar to that shown under Camera Settings below.
-
Page 4: Camera Settings
AMERA ETTINGS 1. After typing in your user name and password, you will be shown the standard browser interface to the camera. 2. The system will attempt to install an ActiveX control to show the camera image in the browser window. - Page 5 5. Click UPnP on the left, then click Disable in the both parts of the screen, as shown below. Click Save to store your settings. 6. Under Accounts to the left, click Administrator to bring up the screen below. Click Permit access from guest users, as shown below.
- Page 6 7. Under Accounts to the left, click General User to bring up the screen shown below. 8. Click Guest in the list, then click Modify. This brings up the Access Level options. Select Unlimited in the drop down, as shown below, and then check (turn on) all the options, as shown below.
- Page 7 9. Click Network(IPv4) to bring up the network settings screen shown below. 10. Click Static in the Connection Mode to bring up the screen below. 11. Set the IP address to the desired value: we suggest setting the first camera to 192.168.0.80, the second to 192.168.0.81, and so forth.
- Page 8 12. If prompted, click to Restart to restart the camera. Note that the camera is now at a different IP address, so the browser window won’t show the camera. 13. Go to the address line in the browser, and put in the new IP address as shown below: 14.
- Page 9 ERSION Devices Variable Name Setting Comments Communication Device N/A (See Note 1) N/A (See Note 1) <User Defined> (Default: Panasonic KX/BL/BB Series) Video Cameras Name Device Type Panasonic KX/BL/BB Series Location <User Defined> (Not Required) IP Address <User Defined> (Default: 192.168.0.80) (See Note 2) Notes: 1.