Advertisement
For your own safety, turn switch OFF and remove plug
from the power source outlet before maintaining, or
lubricating your belt / disc sander.
1.
Frequently blow out or vacuum out any dust that may
accumulate inside the motor.
2.
Remove impacted sawdust from the disc and belt
abrasive or replace abrasive.
Certain cleaning agents and solvents damage plastic
parts. Some of these are: gasoline, carbon tetrachloride,
chlorinated cleaning solvents, ammonia and household
detergents that contain ammonia. Avoiding use of these
and other types of cleaning agents, minimizes the
probability of damage.
To avoid shock or fire hazard, if the power cord is worn or
cut, or damaged in any way, have it replaced immediately.
All repairs, electrical or mechanical, should be attempted
only by trained repairmen. Contact the nearest Sears
Service Center.
LUBRICATION
All of the BALL BEARINGS are packed with grease at
the factory. They require no further lubrication.
TROUBLESHOOTING
GUIDE
Turn switch OFF and always remove plug from power source before making any adjustments or repairs.
All repairs, electrical or mechanical, should be attempted only by qualified service technicians.
Contact the nearest
Sears Service Center.
PROBLEM
Motor will not run.
Machine slows down
while sanding.
Sanding belt runs off pulleys.
PROBABLE CAUSE
1. Defective or broken ON/OFF switch.
2. Defective or damaged switch cord.
3. Defective or damaged switch relay.
4. Burned out motor.
5. Blown house fuse.
.
2.
3.
1.
Operator applying too much
pressure to workpiece.
Dirt on wheels.
Worn or stretched belt.
Not tracking properly.
1. Sanding disc or belt glazed with sap.
2. Excessive pressure being applied
to workpiece.
Wood burns while sanding.
REMEDY
1-3. Replace all broken or defective
parts before using sander.
4.
Consult your local Sears Service
Center. Any attempt to repair this
motor may create a hazard unless
repair is done by a qualified
technician.
5.
Replace house fuse. Turn OFF
other appliances and power tools
on the same circuit.
1.
Use less pressure in applying
workpiece to sanding surface.
2.
Clean wheels.
3.
Replace pulley belt.
1.
Adjust tracking. See section
"REPLACING SANDING BELT".
1.
Replace belt or disc.
2.
Reduce pressure applied to
workpiece.
Motor overheats
1. Motor overload.
1.
r_educe motor load. Allow
to cool off before restarting.
:!!_!,!!
i;!i:ii_i!i_i!il
,i! _iiii'
iiiiii!i!
!iiii,ii!_iii!_i_!!!i;i!;;i_iiii!i!!i
i!!_!i
_i_;i;_iii!i!_iil;!i
_; _i_ii?ii_!!i!i:!
i!il !_i_i_i_ii:_!;iiii!i_i!il;i_ii!i_!ii_il
i;i_i_i_i
!! ! ::i! _ilii !,! iili ¸ :ii!iiiii!_!_
iii% !ili!i_!ii!_!_ii!:ii
!iiii_i_!!iii_;i;!i!_
!ili'iiiiii_i!i!!i_!?i_i!ili!iil;iii_!!!i:i
il;!i !!iiiii_!i!iiii!:i,il
!! i ii_il
!i 17 ii!!iiii!iiii!ii!!!_!ili!i!ii_!i
¸ iii iii:!!i!!i!iii_!i_'_!ii!!i!i
!!;i_!i!!i!!i!ili
ii_i_!ili_i:i:iii!ii!iiiiili!!;!
,iiii_;_!!!!i!!iiii!i,i
:i!i:_i_!i:i
i_i i_iiiiiii
_! _i,i!
_ii:iiii_
!iii ii:i_i_il
_ii_ii_!_ii
i_i'i!_iiiiiiii!i_i!!ili_i_i!!i!iii_i_i!_
i!_iiiii?!!!!!_!i_i!_ii
i!ii,!il
_!i_ii
ili!iii_
:!!_ii!i'
!ii _ !_i:
i¸ i_¸ i:_il !;_ _ :_ _ ii_i !i_
Advertisement
