1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Sander
  5. 113.226423
  6. Owner's manual

Craftsman 113.226423 Owner's Manual

Belt and disc sander
Hide thumbs
Table of Contents

Advertisement

Quick Links

i i ii
ii
i, ii ii
ii i
i
SAVE THIS MANUAL
FOR FUTURE REFERENCE
MODEL NO.
113.226423
BELT AND
DISC
SANDER
Serial
Number
Model
and serial number
may be found on the back
side of the base,
You
should
record
both
mode! and serial number
in
a safe place for future use.
CAUTION:
Read GENERAL
and ADDITIONAL
SAFETY
INSTRUCTIONS
carefully
C
F'rs
BELT AND DISC
SANDER
® assembly
• operating
e repair parts
Sold
by
SEARS,
ROEBUCK
AND
CO.,
Chicago,
IL 60684
U.S.A.
PART
NO
SP500t
_:_;_ !_::D
t;
_. _ ;:

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 113.226423

Summary of Contents for Craftsman 113.226423

  • Page 1 i i ii i, ii ii ii i SAVE THIS MANUAL FOR FUTURE REFERENCE MODEL NO. 113.226423 BELT AND DISC SANDER Serial Number Model and serial number F'rs may be found on the back side of the base, should record both mode! and serial number BELT AND DISC...

  • Page 2: Full One Year Warranty

    FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER If within one year from the date of purchase, this Craftsman Belt and Disc Sander fails due to a defect in material or workmanship,: sears will repair it, free of charge. WARRANTY...

  • Page 3: Direction Of Feed

    21. DIRECTION OF FEED 22. NEVER LEAVE TOOL RUNNING UNATTENDED Feed work into a blade or cutter against the direc- Turn power off. Don't leave tool until it comes to a tion of rotation of the blade or cutter only. complete stop.
  • Page 4 additional safety instructions for belt and disc sander 12; Think Safety Safety is a combination of operator common sense and alterness at all times when the sander is in operation. The operation of any power tool can "es@t in foreign objects being thrown into the eyes, which...
  • Page 5 motor specifications and electrica requirements This plug requires a mating 3-conductor grounded type This machine is designed to use, and is equipped with, outlet as shown. a 3450 RPM motor, It is wired for operation on 110-120 volts, 60 Hz., alternating current. (TOOL MUST NOT If the outlet you are planning to use for this power tool BE CONVERTED TO OPERATE ON 230 VOLT).

  • Page 6: In The Box

    Unpacking A ndChecking C ontents ..__._ .. 6 Be!t Table Stop ......Surface Sanding on Sanding Belt ... Mounting Belt and Disc Sander to Workbench End Sanding on the Sanding Belt ... Clamping Bell and Disc Sander to Workbench ..

  • Page 7: Mounting Belt And Disc Sander To Workbench

    assembly MOUNTING BELT AND DISC SANDER TO WORKBENCH If belt and disc sander is to be used in a permanent location, it should be fastened securely to a firm sup- porting surface such as a workbench. A 5/16" bolt, flat- washer, Iockwasher, and hex nut (not included) should be used at each mounting hole to secure the belt disc sander to the workbench.

  • Page 8: Alternate Mounting Method

    assembly 7. If you prefer to mount your sander to a leg set we recommend the leg set for bench top tools which is available through Sears Retail or Catalog Stores, The number of this leg set is 9-22244. This leg set is an optional accessory and instructions to mount the belt and disc sander to this leg set are included in the leg set package.

  • Page 9: Installing Timing Belt

    MOUNTING BOLTS BELT AND DISC SANDER Securely clamp board to workbench using "C" clamps. SPECIAL NOTE: The supporting surface where belt and disc sander is mounted should be examined carefully after mounting is complete to insure that no movement during use can occur, tf any tipping or walking is noted, secure workbench or supporting surface before operating belt and disc sander.

  • Page 10: Installing Sanding Disc Plate

    4. The lower pulley/motor shaft can now be raised TIMING3ELT TENSION 5. enough ltoslip the belt over both pulleys. ADJUSTMENT S ET While moving the lower pul{ey/motor shaft Up and SCREW down, begin to tighten the timing belt tension adjust- ment screw.

  • Page 11: Installing Backstop

    SANDING FLAT DRIVE PLATE 3N SHAFT', SHAFT 3 Alignflaton shaftwithsetscrew in sanding plate Slide sanding plate ontoshaftuntil p late surface and shaftarenearly flush Donotallowshaftto extend out past surface of sanding ptate or damage may occur to your sanding disc during operation GUARD NOT SHOWN FOR CLARITY WRE_4OH...
  • Page 12 bolt among loose _arts. insert rod in base as shown, leaving 5 inches of rod extending outside base, BASE ..3. Install bolt in base (align a flat side of rod to bolt) and tighten with 1/2 inch wrench. 4. Slide table assembly onto rod. WARNING: To avoid trapping the work or fingers between the table and sanding surface, the table...
  • Page 13 7. To adjust table so it is parallel to sanding surface, locate two allen head set screws on bottom side of ALLEN HEAD the table, 8. Loosen these two set screws and position the table parallel to the sanding surface. (There should be a minimum gap of 1/16"...

  • Page 14: Replacing The Sanding Belt

    assembly NOTE: This unitcomes with the sanding bert installed. DIRECTIONAL ARROW REPLACING THE SANDING BELT - DRIVEPULLEY TENSIONING AND TRACKING WARNING: To avoid injury from accidental start, BANDING BELT turn switch "OFF" and remove plug from power source outlet before removing or installing sanding belt.

  • Page 15: Product View

    getting to know your beat and disc sander WARNING: To avoid injury from accidental start, _urn switch "OFF" and remove plug from power Jource outlet before making any adjustments. BACKSTOP LOCK SANDING BACKSTOP BOLT BELT PLATE TABLE BELT BELT TRACKFNG TABLE KNOB SANDING...

  • Page 16: On/Off Switch

    getting to know your belt and disc sande " 9. ON-OFF SWITCH The On-Off Switch has a locking feature. THIS FEA- 1, To turn machine "ON" insert key into switch. NOTE: Key is made of yellow plastic; locate in loose parts bag.

  • Page 17: Bevel Sanding

    basic operation BEVEL SANDING _The worktable can be tilted from 0 ° - 45 ° for bevel sanding. Loosen the table lock knob and tilt the work- table to desired angle as shown. WARNING: To avoid trapping the work or fingers between the table and sanding surface, the table should be repositioned on the table support rod to...

  • Page 18: Surface Sanding On The Sanding Belt

    BELT TABLESTOP a.Loosen, the locknutusinga 314-inch wrench. WRENCH b. Placea level o n the abrasive belttableandusing a 3/4-inch wrench, screwthestopboltinoroutuntit thebelttableis level, c. Tighten thelocknut. BACKSTOP WORKPIECE SURFACE SANDING ON THE SANDING BELT Hold the workpiece firmly with both hands, keeping fingers away from the sanding belt.

  • Page 19: Miter Gauge

    ,_SANDING CURVED EDGES DURVED EDGES Sand inside curves on the idler pultey, Sand outside curves on the sanding disc. , i,,1[ !ll,ii , ....ii, ...... MITERGAUGE SANDING SMALL END SURFACES ON THE SANDING DISC Move the work across the center to the left side of the face of the sanding disc.

  • Page 20: Wiring Diagram

    be hazardous. The table may be tilted for beveled work. maintenance WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before adjusting, maintaining, or lubricating your belt and BLACK disc sander. BLACK JUMPER _,,_,,,=o r-OO D RED t._aYt/ SWITC._"L:: "...
  • Page 21 shooting trouble WARNING: For your own safety, turn switch "OFF'" and remove plug from power source outlet before trouble shooting your sander, TROUBLE PROBABLE CAUSE REMEDY ,.,,,,, ,,,J ,, , , ,, ,,,,,.,IL i,,, ,,,,,,, , ,L , '",",,,.'_ ,,, ..Motor will not run, 1.

  • Page 22: Parts Layout

    PARTS LIST FOR CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.226423 Green Ground Leac ,77!

  • Page 23: Parts List

    PARTS LIST FOR CRAFTt "AN BELT AND DISC SANDER MODEL NO. 113,226423 Always order by part no. and description -- not by key no. Part No. Part No. Description Description 813909 814669 Washer, Rubber Pulley-Drive 814105 STD502502 *Screw-Set, Hex. Cup 1/4-20x1/4 Pulley-Timing Belt 8t4002-1 805642-6...

  • Page 24: How To Order Repair Parts

    BELT AND DISC SANDER SERVICE Now that you have purchased your Belt & Disc Sander should need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores, Be sure to provide all pertinent facts when you call or visit.

Table of Contents