Advertisement
Quick Links
Owner's
ManuaW
®
4"x 36" Be_t
6" Disc
/ D_SCSANDER
_,... "... : ..".: ',.14 ..}
///
E82443
c@
37J2 LISTD
O
CAUTWON:
Before using this Belt / Disc Sander,
read this manual and follow
all its Safety Rules and
Operating
Instructions.
o Safety Rnstructions
o Rnstailation
o Operation
o Maintenance
o Parts List
@ust@_÷_
Neip
LBn÷
t -8@@-843-1682
Sears
Canada
lnco, TorOnto
M5B 2B8
Part No. 137283290001
l
Advertisement
Related Manuals for Craftsman 137.283290
Summary of Contents for Craftsman 137.283290
- Page 1 Owner's ManuaW ® 4"x 36" Be_t 6" Disc / D_SCSANDER _,... "... : ..".: ',.14 ..} E82443 37J2 LISTD CAUTWON: o Safety Rnstructions o Rnstailation Before using this Belt / Disc Sander, read this manual and follow o Operation all its Safety Rules and o Maintenance Operating Instructions.
-
Page 2: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS SECTION PAGE WEAR YOUR ALWAYS WEAR EYE PROTECTION. Any belt / disc BEFORE USING THE BELT / DISC SANDER Warranty ..............sander can throw foreign objects into the eyes which Product Specifications ............Safety is a combination of common sense, staying alert could cause permanent eye Safety _nstruct]ons... -
Page 3: Grounding Instructions
24. DONOToperate t hetoolif youareunder t heinfluence ALWAYS maintain a minimum clearance of 1/16 inch GROUNDING INSTRUCTIONS This tool is intended for use on a circuit that has a of anydrugs, a lcohol o r medication t hatcould affect or less between the table or backstop and the sanding receptacle like the one illustrated in FIGURE A. - Page 4 ITEM DESCRIPTION QUANTITY Belt / Disc Sander Disc Disc housing Disc table AVAmLABLE ACCESSORqES Miter gauge Tension lever Sanding disc Disc housing Back stop Sanding belt Disc dust chute Belt dust chute LIse only accessories recommended for this belt / disc Loose parts in bag: sander.
- Page 5 SANDING DISC INSTALLATION (FIG. G) PULLEY COVER INSTALLATION (FIG. E) Remove and clean any adhesive or material left on the Attach pulley cover (1)using the 40mm long pan head screw (2) and 12mm pan head screw (3), as shown. disc plate (2). Peel plastic backing from abrasive disc (1) and carefully press disc firmly in position around the Tighten screws securely.
- Page 6 ADJUSTMENTS Fig. M TABLE ASSEMBLY INSTALLATION (FIG. I) Fig. J The worktable can be used with either the sanding disc or the sanding belt. It should be used to support workpieces in all sanding operations except inside curve applications. To avoid injury, always keep the plug disconnected from Insert the table support rod (1) into the sander base the power source and the switch turned OFF until the hole as shown.
- Page 7 SAFETY POWER SWITCH (FIG. O) WRENCH (FIG. Q) REPLACING SANDING BELT (FIG. S, T, U) Fig= U Insert the handle of the wrench into the metal clip located on the sander as shown. To avoid injury, always keep the plug disconnected from To avoid injury, turn switch OFF and disconnect the plug Fig.
- Page 8 ADJUSTING SANDING ARM SANDING INSIDE CURVES (FIG. Y) END GRAIN SANDING WITH THE BELT (FIG. AA) When sanding the ends of the wide workpieces it is Freehand sanding of inside curves can be sanded on the LEVELING THE ARM (FIG. W) idler drum (1).
-
Page 9: Troubleshooting
TROUBLESHOOTING GUIDE For your own safety, turn switch OFF and remove plug To avoid shock or fire hazard, if the power cord is worn or from the power source outlet before maintaining, or cut, or damaged in any way, have it replaced immediately. lubricating your belt / disc sander. - Page 10 4" x 36" BELT/DISC SANDER MODEL NO. 137.283290 When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this belt / disc sander may create a HAZARD unless repair is done by a qualified service technician.