Craftsman 126.32563 Operator's Manual page 41

022-0101 Base Full Assembly 1 35.
Work Piece Clamp 1 36.
022-0114 Rotating Table Ass 1 37.
022-0229 Retract Guard Assy 1 38.
022-0160 Head Assembly 1 39.
022-0174 Motor Assembly 1 40.
022-0191 Handle Assembly 1 41.
022-0102 Base Assembly 1 42.
022-0129 Rocking arm Ass 1 43.
022-0134 Front base Ass 1 44.
022-0234 Position handle 1 45.
1. 022-0103 Base 1 46.
2. 022-0104 Washer 8mm 4 47.
3. 022-0105Screw M6X14mm 13 48.
4. 022-0106Screw M8X16mm 4 49.
5. 022-0107 Extension Arm 2 50.
6. 022-0108Screw M6X12mm 2 51.
7. 022-0109Screw M6X35mm 4 52.
8. 022-0110 Plastic foot 2 53.
9. 022-0111 Leg Location 4 54.
10. 022-0112 Base support 2 55.
11. 022-0113 Fence 1 56.
12. 022-0115 Turnplate 1 57.
13. 022-0116 Locking screw 1 58.
14. 022-0117 Square nut M10mm 1 59.
15. 022-0118 Left blade throat 1 60.
16. 022-0119 Turnplate indicator 1 61.
17. 022-0120 Neck locking bolt 1 62.
18. 022-0121 Neck locking knob 1 63.
19. 022-0122 Bevel shaft 1 64.
20. 022-0123 Clamp 1 65.
21. 022-0124 Right blade throat 1 66.
22. 022-0125Screw M4X10mm 10 67.
23. 022-0126 Knob 1 4 68.
24. 022-0127 Locking nut M10mm2 69.
25. 022-0128 Washer 10mm 2 70.
26. 022-0130 Neck 1 71.
27. 022-0131 Linear Slide bearing4 72.
28. 022-0132 Neck handle 1 73.
29. 022-0133 Retainer plate 2 74.
30. 022-0135 Pivoting Block 1 75.
31. 022-0136 Slide poles 2 76.
32. 022-0137 Slide bar block 1 77.
33. 022-0138Adjust depth stop 1 78.
34. 022-0139 Screw 2 79.
022-0140 Hold down pin
022-0141 Front base case A
022-0142 Front base case B
022-0143 Laser
022-0145 Angle indicator
022-0146 Pivot pin axle
022-0147 Open cirlip 16mm
022-0148 Screw M6X12mm
022-0149 Hex nut M6mm
022-0150 Screw M6X20mm
022-0151 Screw M6X45mm
022-0152 Screw M6X30mm
022-0153 Screw M6X12mm
022-0154 Screw M6X6mm
022-0155 Screw M6X16mm
022-0156 Screw M4X12mm
022-0157 Screw M4X14mm
022-0158 Screw M4X10mm
022-0159 Screw M5X10mm
022-0161 Main Guard
022-0162 Armature
022-0163 Bearing
022-0164 Bearing
022-0165 Right cover
022-0166 Left cover
022-0167 Back casing
022-0169 Bearing Housing
022-0170 Bearing
022-0171 Arbor Shaft
022-0172 Gear
022-0173 Arbor lock
022-0175 Motor housing
022-0176 Stator
022-0177 Flow guide
022-0178 Motor end casing
022-0179 Bearing mount
022-0180 Brush holder
1
1
1
1
1
1
2
1
5
2
1
1
2
4
1
3
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
022-0181 Screw ST4.2X70mm2
022-0182 Screw ST4.2X12mm2
022-0183 Saw depth adjust 1
022-0184 Inner flange 1
022-0185 Outer Flange 1
022-0186 Blade 1
022-0187 Guard retain plate 1
022-0188 Spring 1
41