Download Print this page
Yamaha RX-V467 Update

Yamaha RX-V467 Update

Firmware update version f018 (including htr-4063/htr-5063)
Hide thumbs Also See for RX-V467:

Advertisement

September, 2010
Subject: RX-V467/RX-V567 Firmware Update Version F018
(Including HTR-4063/HTR-5063)
Yamaha is pleased to offer the following firmware update to ensure the best possible
performance and features for your Yamaha RX-V467/RX-V567 AV Receiver. This
firmware adds 3D video pass-through capability for the HDMI connections and improves
stability with 3D signals from DirecTV set-top boxes.
Requirements:
A personal computer capable of burning an audio CD
BD/DVD/CD player* with digital audio connection
(Optical or Coaxial, not HDMI)
*Note
CD PLAYER IS PREFERRED.
Some DVD players use digital filters, which affects the output signal of the
devices. This firmware update may not work with DVD players which use these
digital filters. CD players usually do not use these filters.
CHECK THE UNIT'S FIRMWARE VERSION PRIOR TO THIS UPDATE
The firmware version consists of a letter followed by three numbers [ex. "F018"].
If the three numbers in the firmware version are 018 or higher, you
perform this update.
How to check your firmware version:
Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you
press the [STANDBY/ON] button. Once the front panel displays "ADVANCED SETUP",
release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for
about 3 seconds until front panel display shows the firmware version.
The following pages contain the firmware update instructions for Yamaha AV receivers
RX-V467/V567. The outline of the update is as follows:
1. Create an update disc (Audio CD)
2. Connect digital audio with CD, DVD or BD player
3. Enter firmware update mode
4. Play the update disc (Reprogramming)
5. Confirm update firmware version
< IMPORTANT NOTICE >
Do not attempt to update your Yamaha receiver using any other data file except those provided
directly from the Yamaha website.
Follow the instructions carefully and do not attempt any other procedures not specified in the
instructions provided by Yamaha.
Improperly updated products may cause improper operation, and any parts or service required
to restore proper operation will not be covered under the Yamaha Limited Warranty.
Firmware Update Procedure for RX-V467/RX-V567
Page.1 of 5 Sep
DO NOT
need to

Advertisement

loading

Summary of Contents for Yamaha RX-V467

  • Page 1 5. Confirm update firmware version < IMPORTANT NOTICE > Do not attempt to update your Yamaha receiver using any other data file except those provided directly from the Yamaha website. Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by Yamaha.
  • Page 2 Firmware Update Procedure for RX-V467/RX-V567 Instructions for Firmware Update: STEP1 CREATE UPDATE DISC Download the firmware from YAMAHA website. Unzip and burn the WAV file onto CD-R/RW as an Audio-CD. This will be your update disc. If you need instructions on creating this firmware update CD, see your Personal Computer ("PC") CD burning software instructions on how to burn WAV file as an...
  • Page 3: Tone Control

    Firmware Update Procedure for RX-V467/RX-V567 STANDBY/ON INFO TONE CONTROL STRAIGHT STEP3 ENTER FIRMWARE UPDATE MODE Plug the AC power cable of the AV receiver. Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you press the [STANDBY/ON] button. Once the front panel displays "Advance Setup", release the [STRAIGHT] button.
  • Page 4 Firmware Update Procedure for RX-V467/RX-V567 STEP5 CHECK UPDATED VERSION Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you press the [STANDBY/ON] button. Once the front panel displays "ADVANCED SETUP", release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for about 3 seconds until front panel displays “M:F018 66A8”...
  • Page 5 Step PL2. On the front panel of the AV receiver, press and hold the [INFO] button and keep it pressed, while you plug the AC power cable of the Yamaha receiver to the wall outlet. Once the front panel displays "CDDA Upgrader"...

This manual is also suitable for:

Rx-v567