Epson Pro 7600 Unpacking And Setup Manual
Epson injet printer stylus pro 7600 / 9600 unpacking and setup guide
Hide thumbs
Also See for Pro 7600:
- Product support bulletin (104 pages) ,
- Manual (5 pages) ,
- Quick reference manual (11 pages)
Table of Contents
Advertisement
Quick Links
Unpacking and Setup Guide
Copyright ©2002 by SEIKO EPSON CORPORATION, Nagano, Japan
®
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking and Assembling Stylus Pro 9600 . . . . . 2
Unpacking and Assembling Stylus Pro 7600 . . . . . 8
Setting up Stylus Pro 7600/9600 . . . . . . . . . . . . . . 13
Using the User Guides . . . . . . . . . . . . . . . . . . . . . . 20
4020360-00
EUL
Advertisement
Table of Contents
Related Manuals for Epson Pro 7600
Summary of Contents for Epson Pro 7600
-
Page 1: Table Of Contents
Unpacking and Assembling Stylus Pro 7600 ..8 Setting up Stylus Pro 7600/9600 ....13 Using the User Guides ..... . 20... - Page 2 SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers.
-
Page 3: Safety Instructions
If ink gets on you skin, wash it off with soap and water. If it gets in your eyes, flush them immediately with water. If you use EPSON UltraChrome ink cartridges, shake the ink cartridge gently before installing it for best results. -
Page 4: Unpacking And Assembling Stylus Pro 9600
For United Kingdom Users Use of options EPSON (UK) Limited shall not be liable against any damages or problems arising from the use of any options or consumable products other than those designated as Original EPSON Products or EPSON Approved Products by EPSON (UK) Limited. -
Page 5: Unpacking And Assembling The Printer
Caution: The printer unit is heavy and unwieldy. Have two people unpack the printer unit, and four people place the printer unit on top of the base unit. Parts: Base upright, left... - Page 6 Tools: Hex wrench Hex socket head bolts (4) Wing nuts and spring washers (2) I is for connecting the printer unit to the base unit. Paper feed support films (5) Assembling the base unit Caution: Have two people working on either side to assemble the base unit (20.5 kg).
- Page 7 Place the casters sideways and lock them so they will not move. Roll paper spindle Roll paper (EPSON Doubleweight Matte Paper; 5 m) Ink cartridges (Yellow, Cyan, Magenta, Light Cyan, Light Magenta, Black1, Black2) Roll paper belt (for keeping roll paper wound up)
- Page 8 2. Remove the protective materials of the paper guides from underneath the printer. 3. Position the base unit in front of the printer unit as shown. 4. Mount the printer on the base unit as shown below. Caution: Do not attempt to lift the printer unit with fewer than four people.
-
Page 9: Attaching The Paper Basket
7. Remove the protective materials. from the front cover (tapes) from the ink compartment cover (tapes) from the side of the print head compartment (fixing metal plate inside the front cover) Caution: Watch your fingers when opening and closing the front cover. 8. -
Page 10: Unpacking And Assembling Stylus Pro 7600
Leave at least 15 cm between the back of the printer and the wall. Place the printer on a desk. If you can not place the printer on a desk, you will need the optional Stand. If you place your printer on a desk, follow the guidelines listed below. -
Page 11: Unpacking The Printer
(B) around the printer unit. 2. Remove the fixers from the sides of the box. Lift the box up and away from the printer, then fold it and set it aside. 3. Remove the cardboard panels. - Page 12 4. Remove the protective materials: from the front cover (tape). from the side of the print head compartment (inside the front cover). from the ink compartment cover (tape). Note: Do not re-install the screw. Store it separately to avoid losing it. Using the Optional Stand Checking the contents of the package Before assembling the Stand, check the contents of...
- Page 13 Hold the printer at the indicated locations as shown. If the ink cartridges are installed, do not tip the printer at an angle. Otherwise, ink may leak from the cartridges. 1. Position the printer and the Stand as shown.
-
Page 14: Attaching The Paper Basket
2. Mount the printer on the printer mount as shown. 3. Fasten the bottom of the printer and the printer mount with wing screws (N) and washers (O). 4. This completes the mounting procedure. Make sure the printer and the Stand are fastened together securely. -
Page 15: Setting Up Stylus Pro 7600/9600
Setting up Stylus Pro 7600/9600 Connecting the power cord 1. Make sure that the printer is off. It is off when the surface of the Power button is even with the button protectors. 2. Connect the power cord to the AC inlet on the back of the printer. - Page 16 Note: If you use the EPSON UltraChrome ink cartridge, shake the cartridge gently before installing it. 4. Hold the ink cartridge with arrow mark on the left side and pointing to the rear of the printer, and insert it into the slot until the corresponding Ink Out light turns off.
- Page 17 If you do not use the paper set above, remove it from the printer. When you use roll paper, set the paper lever to the released position, and wind it up. When you use cut sheet, remove the paper from the printer...
-
Page 18: Reusing The Packaging
Note: The EPSON Printer Port and DMA transfer features (For Windows Me, 98, and 95 only) of the EPSON printer driver you install are not available with USB connections. They are available only with the parallel interface connection. - Page 19 The online Reference Guide helps you learn more about your printer. If you are using the floppy disk version of the software, make a backup copy of the EPSON printer software disk before you begin installation. If you wish to make a floppy disk...
- Page 20 7. Follow the on-screen instruction. Note: If an error message appears, either the printer driver or the EPSON USB printer device driver is not installed correctly. See “Troubleshooting” in the online Reference Guide. Ensuring that the USB driver is installed...
- Page 21 1. Make sure that your printer is off. 2. Turn on your Macintosh, and insert the software CD-ROM shipped with your printer in the CD-ROM drive. The EPSON printer software disk opens automatically. 3. Double-click EPSON icon. 4. Choose your printer from the windows, then click the right arrow.
-
Page 22: Using The User Guides
With background printing on, you can use your Macintosh while it is preparing a document for printing. In order to use the EPSON Monitor3 utility to manage print jobs, background printing must be turned on. 3. Close the Chooser. 4. Check the label on the back of the printer to... - Page 24 Printed in Japan 00.xx-xx...