Issue: 1.0 Warnings and Cautions If you fail to read this information and handle the product incorrectly, death or serious injury may occur. This device MUST be securely anchored to a solid surface in a manner that will resist wind, snow and ice loading, and any other hazard which might compromise the security of the mounting.
Issue: 1.0 Always stop using when the product if it should emit smoke or abnormal heat. Never install the product in area exposed to oil or gas; this PTZ is NOT rated as ‘explosion proof’. Never install the product on a surface that cannot hold its weight. Never touch the power cord with wet hands.
DVR in place of optical zoom at the PTZ allows the recording of an area 16 times that being analyzed on screen by systems comprised of EverFocus DVRs and HDcctv cameras. A full function PTZ speed dome, the EPH5212 features everything you expect from a high quality PTZ: 360° ’endless pan’...
Issue: 1.0 1.3 System Configuration 1.4 Termination Settings [SW303: Refer to 2.4 Dome Camera Settings] To prevent malfunctions and/or interference with communication signals between the camera and controller, the domes (shaded with gray color) at the end of line must have their terminations set to ON. All other domes in the “chain”...
Issue: 1.0 2.2 Base Installation - Make holes for mounting and cable hole on the wall where the dome camera is to be installed. Attach the arm firmly with the supplied mounting screws (4) or other means which will secure the unit properly to resist wind and snow/ice loading.
Issue: 1.0 2.3 Connection Interface and Wiring cables *Caution Do not connect the power cable until all other connections have been completed. Be sure to remove the shipping foam ring and sheet before connecting the power to the dome camera. 2.3.1 Connecting the RS-485 lines The dome camera can be controlled remotely by an external device or control system such as a controller using RS-485 half duplexer (RS-485 Connection).
Issue: 1.0 2.4 Setting RS-485 Parameters The device can communicate with external controllers and DVRs by setting the Rotary switches and Dip switches. Refer to the tables below for setting the dome camera ID and protocol. Total length of the cable for communication should not exceed 1km.
Page 11
Issue: 1.0 S W 3 0 2 S W 3 0 1 S W 3 0 3 J 3 0 2 3. Programming PTZ and Camera Functions and Options [OSD Menu Structure] Main Menu/Title Operation Menu...
Page 13
Issue: 1.0 This manual is designed to be a reference for the programming and operation of the system. You can see information about features of the dome and commands as well as an operation method. The symbols below mean some action of the joystick controller. ▲/▼: move joystick up and down : move joystick left and right direction ◀...
Issue: 1.0 3.1 Getting Started You should install and connect the dome to an interface device before using this operating guide. Refer to {2. Installation and connection of this manual}. Once installed, apply power to the dome and the start-up screen is displayed on the monitor. Before installing and operating the dome camera, please read this user’s manual carefully.
Issue: 1.0 The title edit menu can be used in the setup for Preset/Pattern/Tour/Scan commonly. - Move the joystick right in Main Menu. The screen appears on the monitor: - Move the joystick right, left, up or down to select a character. - Press [Tele] button to input a character and [Wide] button to cancel the character.
Page 16
Issue: 1.0 The system Information displays model name/Running Version/Protocol/Communication Type/Camera ID No./System. It is read only for reference. Use the following steps to display the System Information screen: Camera ID changes with respect to ID switching setting. - Enter into {Main MENU} - Select {System} using the joystick [ ▶...
Issue: 1.0 Use this function to initialize all or specific parameters of dome to factory default parameters. - Enter into {Main Menu} - Select {System} using joystick [ ] and move to {Initialize} in the sub menu of {System} ▶ - Select items to be initialized.
Page 18
Issue: 1.0 ▲/▼: move joystick up and down for selecting an item. ◀ ▶ : move joystick left and right for moving an item. / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶...
Page 19
Issue: 1.0 - Enter into {Main Menu} - Select {Display} and move to {Setup} using joystick [ ▶ - Use the joystick to move the label up, down, left, and/or right. - Press [Tele] button to edit the position of labels. - Move the joystick right [ ] to change the status of labels ▶...
Issue: 1.0 3.4.4 Image Setup This menu is for changing displayed image settings. - Enter into {Main Menu} - Select {Display} and move to {Image Setup} using joystick [ ▶ - Using joystick [ ] , Normal image, Horizontal image, Vertical image or H/V image can be selected. ▶...
Page 21
Issue: 1.0 ▲/▼: move joystick up and down for selecting an item. : move joystick left and right for moving an item. ◀ ▶ / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶...
Page 22
Issue: 1.0 This feature automatically processes the viewed image to retain color balance over a color temperature range. The default setting for auto white balance is Auto mode. In Manual mode, you can change the R or B gain value to adjust the color on a monitor. *Auto Trace White balance (ATW): It aligns the white balance automatically.
Page 23
Issue: 1.0 increasing the brightness of the overall screen so that subjects being shot with a loss of dark detail due to backlight will have just the right brightness level. - Enter into {Main Manu} - Select {Camera Setup} and move to {AE Setup} using joystick [ ▶...
Issue: 1.0 Sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. Digital Image Stabilizer (DIS) function internally detects shaking of the image due to camera shaking and performs digital compensation processing inside the DSP to suppress this shaking and stabilize the image output. Compensation uses the electronic zoom function, so the digital zoom function cannot be set by the user while using the DIS function.
Page 25
Issue: 1.0 ▲/▼: move joystick up and down for selecting an item. : move joystick left and right for moving an item. ◀ ▶ / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶...
Page 26
Issue: 1.0 Proportional Pan/Tilt is possible to set manual speed with Zoom. - Use the joystick [ ] to select On/Off ▶ Auto-Flip is a function automatically reversing the image when zoom module camera passes through the top of tilt direction (90 degree) When tilt angle arrives at the top of tilt orbit (90degree), zoom camera module keep moving to opposite direction of tilt to keep tracking targets.
Issue: 1.0 - Using the joystick [ ] to select Auto (On)/Manual (Off). ▶ - Press [Open] button or use joystick to save settings. - Press [Close] button or use joystick to return to previous menu {Dome Motion Setup} (Back). NOTE* In order to call an action (Preset, Pattern, Tour or Scan), you must save Preset, Pattern, Tour, or Scan first.
Issue: 1.0 ▲/▼: move joystick up and down for selecting an item. : move joystick left and right for moving an item. ◀ ▶ / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶...
Issue: 1.0 ▲/▼: move joystick up and down for selecting an item. ◀ ▶ : move joystick left and right for moving an item. / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶...
Issue: 1.0 ▲/▼: move joystick up and down for selecting an item. : move joystick left and right for moving an item. ◀ ▶ / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶...
Issue: 1.0 : move joystick left and right for moving an item. ◀ ▶ / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶ / [Close]/ [Far]: move joystick to cancel or to exit current menu (Back). ▶...
Page 32
Issue: 1.0 / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶ / [Close]/ [Far]: move joystick to cancel or to exit current menu (Back). ▶ - Enter into {Main Menu} - Using the joystick [ ] , select Alarm Input type (NO/NC).
Issue: 1.0 4. Troubleshooting Guide If problems occur, check the installation of the dome with the instructions in this manual. And refer to this manual for further information. Problem Solution Verify that power is connected to all components in the system.
Page 37
Issue: 1.0 APPENDIX. RS-485 Function List Function Preset No. Operation e.g. 1 e.g. 2 1~59, MOVE to Preset Preset Preset+No.+Go Preset+1+Go 101~250 1~59, SET Preset Preset Preset+No+Set Preset+14+Set 101~250 Run FLIP Preset Preset+No.+Go Preset+33+Go Run PAN ZERO Preset Preset+No.+Go Preset+34+Go Scan Setup Preset Preset+No.+Go...