Product Overview TRENDnet’s compact N150 Easy‐N‐Range Extender, model TEW‐713RE, extends the coverage of your existing wireless N network. Setup is easy with no drivers to install. Simply press the Wi‐Fi Protected Setup (WPS) button on your router or access point, ...
TEW‐713RE TRENDnet User’s Guide Product Hardware Features Front View Side View LED Indicator – The LED indicator is will become solid green when your router is connected to a router/AP and WPS connection is established successfully Flashing red when booting Flashing amber when unable to connect to a device Flashing green when initiating WPS connection LAN Port – Connect an Ethernet cable (also known as a network cable) from your PC to the repeater when you want to setup the device manually, or use it to connect to a wired PC/laptop after the unit is connected to the wireless network On/Off Power Switch – Push the On/Off button to turn your repeater “On” or ...
TEW‐713RE TRENDnet User’s Guide Wireless Networking and Security cards(wireless clients), you may have to set your router to WEP to allow the old adapters to connect to the router. Note: This encryption standard will limit How to choose the type of security for your wireless network connection speeds to 54Mbps. WPA: This encryption is significantly more robust than the WEP technology. Setting up wireless security is very important. Leaving your wireless network open and Much of the older 802.11g hardware was been upgraded (with firmware/driver unsecure could expose your entire network and personal files to outsiders. TRENDnet recommends reading through this entire section and setting up wireless security on your upgrades) to support this encryption standard. Total wireless speeds under new router. this encryption type however are limited to 54Mbps. WPA‐Auto: This setting provides the router with the ability to detect wireless There are a few different wireless security types supported in wireless networking each devices using either WPA or WPA2 encryption. Your wireless network will having its own characteristics which may be more suitable for your wireless network automatically change the encryption setting based on the first wireless device taking into consideration compatibility, performance, as well as the security strength connected. For example, if the first wireless client that connects to your along with using older wireless networking hardware (also called legacy hardware). wireless network uses WPA encryption your wireless network will use WPA ...
TEW‐713RE TRENDnet User’s Guide Setting up TEW‐713RE WPS connection 1. Plug in the device to a power outlet and turn the device on 2. Press and hold the WPS button on the router for 5 seconds 3. Press and hold the WPS button on the TEW‐713RE for 5 seconds 4. The LED will change to solid green once the WPS connection is established Web Browser Configuration 1. Plug in the device to a power outlet and turn the device on 2. Connect a network cable from the TEW‐713RE to your laptop/PC 6. Enter your wireless network’s security key and click Apply 3. Open a web browser and type http://tew‐713re or http://192.168.10.100 4. Enter the Login information (default: admin for username and admin for password) ...
TEW‐713RE TRENDnet User’s Guide DHCP Management The repeater will use an IP address from the router. Hostname: The hostname can be used to access the device under the same network. Multi‐Language http://tew‐713re – When the hostname is changed, the access link changes accordingly. You may select your preferred language in the TEW‐713RE user interface. (see Web Static IP Browser Configuration) Set a static IP address for the repeater IP Address: IP address of the device Subnet Mask: The subnet mask of the device IPv6 Supports Static IPv6 IP address, IPv6 Connection Type allows you to disable or select Static IP Connection. Once Static IP is selected, enter your IPv6 settings in the following fields and click Apply. Network LAN Setting ...
TEW‐713RE TRENDnet User’s Guide Upgrade Firmware Wireless Site Survey TRENDnet may periodically release firmware upgrades that might add features or fix problems associated with your TRENDnet model and version. To find out if there is a firmware upgrade available for your device, please check your TRENDnet model and version using the link. http://www.trendnet.com/downloads/ 1. If a firmware upgrade is available, download the firmware to your computer. 2. Unzip the file to a folder on your computer. This feature allows you to select and connect to the wireless network you would like to 3. Log into the repeater (default http://tew‐713RE) repeat from. 4. Click on Management and Upgrade Firmware 5. Depending on your web browser, next to Firmware Location, click Select File. Management 6. Navigate to the folder on your computer in which the unzipped firmware file (.bin) is located and select it the firmware file. Account 7. Click Apply. ...
TEW‐713RE TRENDnet User’s Guide System Status Export Settings Press Export to export configurations to a local file Wireless Network Import Settings Click Browse to select a configuration file and then click Mode AP or Repeater Mode Import to import a configuration file. Connected Router/AP Shows the connected Router/AP’s Network Name(SSID) Reset to Factory Default Click Load Default Settings to reset to factory defaults. Wi‐Fi Mode Wireless Encryption Type Settings Wi‐Fi Key Wireless Key/Password System Info Firmware Version ...
TEW‐713RE TRENDnet User’s Guide Troubleshooting Q: I typed http://tew‐713re but I am not able to access the unit, what should I do? Answer: 1. Reset the device to factory default settings 2. Connect to the TEW‐713RE using a network cable 3. Make sure your laptop/PC is not joined to any domain 4. Make sure your laptop/PC is on the same subnet as the TEW‐713RE. The default IP address for the TEW‐713RE is 192.168.10.100 (see Appendix) 5. Open a browser and type in http://tew‐713re Q: How do I reset the device? Answer: 1. Reset the device by pressing and holding the reset button at the bottom of the unit for 15 seconds. 2. You can also reset from the management page. (default http://tew‐713re) ...
TEW‐713RE TRENDnet User’s Guide 2. In the Network Preference window, next to "Show:” select Network Status. Appendix You'll see your network status and your IP address settings displayed. How to find your IP address How to set a static IP address for your computer’s Ethernet adapter Note: Please note that although the following procedures provided to follow for your Windows 8 operating system on configuring your network settings can be used as general Go to the Start menu, right‐click and select All apps on the bottom‐right corner guidelines, however, it is strongly recommended that you consult your computer or of the screen. Locate the Windows System tab and select Control Panel. Then operating system manufacturer directly for assistance on the proper procedure for click View network status and tasks under Network and Internet. configuring network settings. b. Click Change Adapter Settings, right‐click the Local Area Connection icon. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4). Command Prompt Method d. Then click Use the following IP address: and enter a static IP address and ...
Page 14
TEW‐713RE TRENDnet User’s Guide b. Click the Network icon. From the Location drop‐down list, select Automatic. d. Select and view your Ethernet connection. e. From the Show drop‐down list, select Built‐in Ethernet and select the TCP/IP tab. From the Configure IPv4 drop‐down list, select Manually. Enter a static IP address and subnet mask and click Apply Now. h. Restart your computer. MAC OS 10.5‐10.8 From the Apple, drop‐down list, select System Preferences. b. Click the Network icon. From the Location drop‐down list, select Automatic. d. Select and view your Ethernet connection. e. In the left column, select Ethernet. From the Configure IPv4 drop‐down list, select Manually. Enter a static IP address and subnet mask and click Apply. h. Restart your computer. ...
Page 15
TEW‐713RE TRENDnet User’s Guide Federal Communication Commission Interference Statement Europe – EU Declaration of Conformity This equipment has been tested and found to comply with the limits for a Class B digital This product is herewith confirmed to comply with the Directive of 1999/5/EC, device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 2006/95/EC, and 2009/125/EC. reasonable protection against harmful interference in a residential installation. This EC No. 1275/2008 equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio EN60950‐1: 2006 + A11 : 2009 + A1 : 2010 + A12:2011 communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or Safety of Information Technology Equipment television reception, which can be determined by turning the equipment off and on, the EN 62311:2008 user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. EN 300 328 V1.7.1 (10‐2006) Class B Increase the separation between the equipment and receiver. Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Connect the equipment into an outlet on a circuit different from that to which ...
Page 16
TEW‐713RE TRENDnet User’s Guide This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in Con la presente TRENDnet dichiara che questo TEW‐713RE è Italiano[Italian] all EU member states and EFTA countries, except in France and Italy where restrictive conforme ai requisiti essenziali ed alle altre disposizioni pertinenti use applies. In Italy the end‐user should apply for a license at the national spectrum stabilite dalla direttiva 1999/5/CE, 2006/95/CE e 2009/125/CE. authorities in order to obtain authorization to use the device for setting up outdoor AršoTRENDnetdeklarē, ka TEW‐713RE atbilstDirektīvas 1999/5/EK, Latviski [Latvian] radio links and/or for supplying public access to telecommunications and/or network 2006/95/EK, un 2009/125/EK būtiskajāmprasībām un citiemar to services. This device may not be used for setting up outdoor radio links in France and in saistītajiemnoteikumiem. some areas the RF output power may be limited to 10 mW EIRP in the frequency range Šiuo TRENDnet deklaruoja, kad šis TEW‐713RE atitinka esminius of 2454 – 2483.5 MHz. For detailed information the end‐user should contact the Lietuvių reikalavimus ir kitas 1999/5/EB, 2006/95/EB ir 2009/125/EB [Lithuanian] national spectrum authority in France. Direktyvos nuostatas. TRENDnet tímto prohlašuje, že tento TEW‐713RE je ve shodě se Česky [Czech] Hierbij verklaart TRENDnet dat het toestel TEW‐713RE in Nederlands ...
Page 17
If a product does not operate as warranted during the applicable warranty period, IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE TRENDnet shall reserve the right, at its expense, to repair or replace the defective OR USE OF TRENDNET’S PRODUCTS. product or part and deliver an equivalent product or part to the customer. The ...
Page 18
These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go ...