Setup Wizard Configuration ..................7 Connect wireless devices to your extended network ............ 9 Advance Setup ....................... 9 How to access the management page after the TEW-736RE is linked to a router or access point ........................9 Change the login password..................10 Change the device name .....................
Setup is simple, with no drivers to install. Simply press the Wi-Fi Protected Setup (WPS) button on your router or access point, then on the TEW-736RE and you’re done—the 300Mbps Easy-N Range Extender is now extending your high performance wireless N network over a large area.
The ideal location to place the range extender is in a location creating a wireless network. Because the TEW-736RE comes with detachable where the wireless of an existing signal is available but weak. The range extender needs antennas, they can be upgraded using theTEW-AI77OB, Duo 7dBi Indoor Omni- to detect the existing wireless signal in order to extend any signal.
How to setup your range extender if your wireless signal is weak, place the router in several locations and There are two ways you can configure the TEW-736RE. The easiest way is to use the test the signal strength to determine the ideal position.
7. Plug in the power adapter into the TEW-736RE and verify that the panel lights are WPS is a feature that makes it easy to setup the TEW-736RE to your wireless network. If your wireless router or access point does not have a WPS button, set up the TEW-736RE 8.
Page 8
TRENDnet User’s Guide TEW-736RE 2. Connect the Power Adapter to the TEW-736RE and then to a power outlet (EU Versions will have a power button on the back. Push the power button to the “On” position). Verify that the power is on 3.
When conducting a wireless scan you may see the router’s wireless network name Note: Once the TEW-736RE is connected to your router or access point you will NO listed twice. This is normal because the TEW-736RE broadcasts the same network...
The device name is used to determine all devices in the network. By default the device page after the TEW-736RE is linked to a router or access point” on page name is “TEW-736RE”. This is the name that appears in your network map or DHCP 4. Click on Administrator and Upload Firmware.
3. Click Rescan if you do not see your wireless network. You can set the TEW-736RE to Static Mode and assign an IP address. However the IP address you assign must be within the same subnet of your network. Any network device outside the subnet will not be able to communicate within the network.
Applied settings on the device can be saved and can be use to restore settings. The There may come a time when the TEW-736RE needs a power cycle or reboot. Instead of device will automatically be configured based on the saved settings. This can be used to unplugging the power adapter and plugging it back on, you can follow the steps below to reboot the device.
Answer: Bar, an error message says “The page cannot be displayed.” How can I access the The TEW-736RE repeats and extends the wireless signal of your wireless network, it is router management page? normal to see 2 of your wireless network name (SSID). You can connect to either of your...
Page 19
EN62311:2008 English Hereby, TRENDware declares that this TEW-736RE is in compliance Assessment of electronic and electrical equipment related to human exposure with the essential requirements and other relevant provisions of restrictions for electromagnetic fields (0 Hz - 300 GHz) Directive 1999/5/EC.
Page 20
NiniejszymTRENDware]oświadcza, że TEW-736RE jest zgodny z zasadniczymiwymogamiorazpozostałymistosownymipostanowieniam iDyrektywy 1999/5/EC. TRENDwaredeclaraqueeste TEW-736RE estáconforme com Português osrequisitosessenciais e outrasdisposições da Directiva 1999/5/CE. [Portuguese] TRENDwareizjavlja, da je ta TEW-736RE v skladu z Slovensko bistvenimizahtevami in ostalimirelevantnimidoločilidirektive [Slovenian] 1999/5/ES. TRENDwaretýmtovyhlasuje, žeTEW-736REspĺňazákladnépožiadavky a Slovensky [Slovak] všetkypríslušnéustanoveniaSmernice 1999/5/ES.
Customers shipping and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. from outside of the USA and Canada are responsible for return shipping fees. Customers...