Download Print this page

Char-Broil 12301719 Product Manual

14” tabletop charcoal grill

Advertisement

Quick Links

14" Tabletop
Charcoal Grill
Product Guide
Model 12301719
Tools needed for assembly:
Phillips Screwdriver
Adjustable Wrench
(Tools not provided)
IMPORTANT: Fill out the product record information below.
Date Purchased
CAUTION:
Read and follow all safety statements, assembly
instructions, and use and care directions before
attempting to assemble and cook.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
Keep this manual for future reference.
WARNING:
CARBON MONOXIDE HAZARD
Burning charcoal inside can kill you. It gives off
carbon monoxide, which has no odor. NEVER burn
charcoal inside homes, vehicles, or tents.
If you have questions or need assistance during assembly, please call
To insure your satisfaction and for follow-up service, register your appliance online at www.charbroil.com/register
FOR OUTDOOR USE ONLY
WARNING:
Failure to follow all manufacturer's instructions could
result in serious personal injury and/or property
damage.
CAUTION:
Some parts may contain sharp edges! Wear
protective gloves if necessary.
1-800-241-7548
.
42804827 - 11/16/11

Advertisement

loading

Summary of Contents for Char-Broil 12301719

  • Page 1: Product Record Information

    14” Tabletop Charcoal Grill Product Guide Model 12301719 Tools needed for assembly: Phillips Screwdriver Adjustable Wrench (Tools not provided) IMPORTANT: Fill out the product record information below. Date Purchased FOR OUTDOOR USE ONLY CAUTION: WARNING: Read and follow all safety statements, assembly Failure to follow all manufacturer’s instructions could instructions, and use and care directions before result in serious personal injury and/or property...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS WARNING Product Record Information ......1 FAILURE TO READ AND FOLLOW INSTRUCTIONS FOR Safety Symbols.
  • Page 3: Grilling

    GRILLING Charcoal is recommended, however, wood or a combination of both may be used as the fuel source for grilling with the fuel source placed and ignited on the charcoal grate. Do not build too large of a fire. We recommend starting a fire with no more than 10 briquettes and adding more as needed during cooking.
  • Page 4 Know When Your Fire is Ready Successful charcoal grilling depends on a good fire. The general rule for knowing when your coals are ready for grilling is to make sure that 80 percent or more of the coals are ashy gray. If you have less than that, the coals are not ready, and if all of them are glowing red hot, the fire is probably too hot.
  • Page 5 Direct and Indirect Grilling Direct Grilling - For most grilling, the ignited coals are spread in a single layer under the food. This is called direct grilling and is appropriate for relatively quick-cooking items such as hamburgers, steaks and most seafood. The single layer of coals emits even, steady heat, whether the grill lid is open or closed, and represents the way most people grill.
  • Page 6: Limited Warranty

    LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*.
  • Page 7: Parts List/ Parts Diagram

    PARTS LIST / DIAGRAM Description TOP LID LID HANDLE DAMPER F/ LID FIREBOWL ASH CATCHER DAMPER F/ ASH CATCHER LEG SUPPORT COOKING GRATE CHARCOAL GRID NOT Pictured HARDWARE PACK … ASSEMBLY MANUAL, ENGLISH … ASSEMBLY MANUAL, FRENCH … HARDWARE LIST SCREW M6 X 11 - 2 PIECES SCREW WITH WASHER M5 X 7 - 4 PIECES SCREW M5 X 7 - 1 PIECE...
  • Page 8 Align the center hole in the Lid Air Vent with the hole in the lid. Insert 1 medium screw through center hole and install M5 nut. Be careful not to over tighten nut to allow proper vent operation. Medium Screw M5 x 7 - 1 piece Medium Nut M5 - 1 piece Align the holes in the Lid handle with the holes in the lid.
  • Page 9 Insert the M5 x 7 washer head screws through the inside of the bowl and into the leg. NOTE: Do not completely tighten the screws at this time. Washer Head Screw M5 x 7 - 4 pieces Place the leg support into the leg hooks to hold the wire leg support. Tighten the screws from step 3.
  • Page 10 Align the holes in the air vent with holes in the ash catcher. Insert two M4 x 8 screws through the air vent ash catcher and ash catcher . Tighten two M4 nuts onto the screws. Be careful not to over tighten nuts to allow for proper vent operation. Screw M4 x 8 - 2 pieces Nut M4 - 2 pieces Insert the ash catcher into the bottom bowl.