Setting The Tuner Region 790; Zone Setup Procedures - Rotel RX-1052 Owner's Manual

RX-1052 AM/FM Stereo Receiver
Setting the Tuner Region
790-
The AM/FM tuner is configured at the factory
for the operation in the region where you pur-
chased the unit: the USA or Europe. Should
you need to change this setting:
1. With the RX-1052 on, press the SPKR B,
TUNE/PRESET, and MONO buttons on the
front panel simultaneously.
2. Use the CD and VIDEO 3 buttons on the
front panel as up/down cursor keys to scroll
through the options until the front panel
display reads "BAND USA" or "BAND
EUR".
3. Use the VIDEO 2 and VIDEO 4 buttons
on the front panel as left and right cur-
sor keys to change the band setting in the
display to the desired choice: USA or EUR
(Europe).
4. After making the selection, use the CD and
VIDEO 3 buttons on the front panel as up/
down cursor keys to scroll through the op-
tions until the word SAVE is displayed.
5. Use the VIDEO 2 and VIDEO 4 buttons
on the front panel as left and right cursor
keys to select SAVE YES to store the new
settings and exit.
If you do not wish to save the new setting,
repeat step 5, but select SAVE NO. Then use
the CD and VIDEO 3 buttons to scroll through
the options until EXIT is displayed. Then use
the VIDEO 2 and VIDEO 4 buttons to select
YES if you want to leave the Setup Menu, or
NO if you want to make additonal changes
in the Setup Menu.
Setting Power Mode
The RX-1052 provides three optional power
on settings that may be useful in certain sys-
tem configurations where the unit is plugged
into a switched AC power outlet:
STANDBY: With the default STANDBY setting,
the unit powers up in standby mode when AC
is applied and the rear panel POWER button
is ON. The unit must be activated using the
front panel STANDBY button or the remote
ON/OFF buttons.
DIRECT: With the DIRECT setting, the unit is
fully activated when AC power is applied and
the rear panel POWER button is ON; how-
ever, it may be put in standby mode using the
front panel STANDBY button or the remote
ON/OFF buttons.
ALWAYS-ON: In ALWAYS-ON mode, the
unit remains fully active whenever AC is pres-
ent and the rear panel POWER button is ON;
the front panel STANDBY button and the re-
mote ON/OFF buttons are disabled and the
unit cannot be put in standby mode.
To change the setting:
1. With the RX-1052 on, press the SPKR B,
TUNE/PRESET, and MONO buttons on the
front panel simultaneously.
2. Use the CD and VIDEO 3 buttons on the
front panel as up/down cursor keys to
scroll through the options until the front
panel display reads "PWR ALWAYON"
or "PWR DIRECT" or "PWR ST BY"
3. Use the VIDEO 2 and VIDEO 4 buttons
on the front panel as left and right cursor
keys to change the setting in the display
to the desired choice.
4. After making the selection, Use the CD
and VIDEO 3 buttons on the front panel
as up/down cursor keys to scroll through
the options until SAVE is displayed.
5. Use the VIDEO 2 and VIDEO 4 buttons
on the front panel as left and right cursor
keys to select SAVE YES to store the new
settings and exit.
If you do not wish to save the new setting,
repeat step 5, but select SAVE NO. Then use
the CD and VIDEO 3 buttons to scroll through
the options until EXIT is displayed. Then use
the VIDEO 2 and VIDEO 4 buttons to select
YES if you want to leave the Setup Menu, or
NO if you want to make additonal changes
in the Setup Menu.
790-

Zone Setup Procedures

Setting a Remote Zone
Maximum Volume
You can set a maximum volume level for each
remote zone.
1. With the RX-1052 on, press the SPKR B,
TUNE/PRESET, and MONO buttons on the
front panel simultaneously.
2. Use the CD and VIDEO 3 buttons on the
front panel as up/down cursor keys to
scroll through the options until the front
panel display reads "Z2 MAX", "Z3 MAX"
or "Z4 MAX".
3. Adjust the volume control on the front panel
or remote to set the maximum volume level
for the zone. The new setting appears in
the display.
22
4. After setting the maximum volume for the
zone, use the CD and VIDEO 3 buttons on
the front panel as up/down cursor keys to
scroll through the options until SAVE is dis-
played.
5. Use the VIDEO 2 and VIDEO 4 buttons
on the front panel as left and right cursor
keys to select SAVE YES to store the new
settings and exit.
If you do not wish to save the new setting, re-
peat step 5, but select SAVE NO. Then use
the CD and VIDEO 3 buttons to scroll through
the options until EXIT is displayed. Then use
the VIDEO 2 and VIDEO 4 buttons to select
YES if you want to leave the Setup Menu, or
NO if you want to make additonal changes
in the Setup Menu.
Setting a Remote Zone Turn-on
Volume
You can set a turn-on volume level for each
remote zone. Whenever the zone is turned on
the volume level will be at the level you set.
1. With the RX-1052 on, press the SPKR B,
TUNE/PRESET, and MONO buttons on the
front panel simultaneously.
2. Use the CD and VIDEO 3 buttons on the
front panel as up/down cursor keys to scroll
through the options until the front panel
display reads "Z2 T-ON", "Z3 T-ON" or
"Z4 T-ON".
3. Adjust the volume control on the front panel
or remote to set the turn-on volume level
for the zone. The new setting appears in
the display.
4. After setting the turn-on volume for the
zone, use the CD and VIDEO 3 buttons
on the front panel as up/down cursor keys
to scroll through the options until SAVE is
displayed.
5. Use the VIDEO 2 and VIDEO 4 buttons
790-
on the front panel as left and right cursor
keys to select SAVE YES to store the new
settings and exit.
If you do not wish to save the new setting,
repeat step 5, but select SAVE NO Then use
the CD and VIDEO 3 buttons to scroll through
the options until EXIT is displayed. Then use
the VIDEO 2 and VIDEO 4 buttons to select
YES if you want to leave the Setup Menu, or
NO if you want to make additonal changes
in the Setup Menu.
790-