Door Handles; Shaker Grate Handle; Smoke Curtain - United States Stove Company 1602R Installation/operator’s Installation & Operator's Manual

Unpack your Furnace and insure that there is no shipping
damage. If damage exist, please contact your dealer im-
mediately.
Your Ashley Furnace will require some assembly before
operation. All needed hardware and components for the
following assemblies are included within the parts boxes
inside the furnace and in the ash pan. Read and follow
these instructions for proper furnace assembly.

DOOR HANDLES

Insert door handle into door. From rear side of door, place
a 1/2" washer over the threaded part of the handle, then
attach the lock nut. Tighten the nut, then back off 1/4
turn to allow free operation of the handle.
Follow these same directions for the ash door handle as-
sembly.
(2) Door Handle
(2) 1/2" Washer
(2) 1/2" Lock Nut
ASH DOOR SPIN DRAFT
Screw the spin draft onto the 3/8" x 2-1/2" carriage bolt.
Then screw the spin draft and bolt into the ash door al-
lowing approximately 1/2" of the bolt to stick through the
back side of the ash door. Secure the bolt in place with
the 3/8"-16 lock nut.
(1) Spin Draft
(1) 3/8-16 Carriage Bolt
(1) 3/8-16 Lock Nut
FUEL & ASH DOOR LATCH
With two 1/4-20 x 3/4 hex bolts each, attach the door
latches to the door latch mounting brackets on the left
side of the door frames as illustrated. The slots in the brack-
ets and latches are for door seal adjustment. Make the
proper adjustments, then tighten the nuts. The door's gas-
ket should be snug against the door frame on the furnace.
(1) Feed Door Latch
(1) Ash Door Latch
(4) 1/4-20 x 3/4 Hex Bolt
(4) 1/4-20 Kep Nut
6
FURNACE ASSEMBLY INSTRUCTIONS
Feed Door Ash Door
Illustration Illustration

SHAKER GRATE HANDLE

Insert the Shaker Rod into the hole on the ash door frame
as shown. Then attach the Shaker Bracket to the front of
the furnace using two 1/4-20 x 3/4" Hex Bolts and two 1/4-
20 Lock Nuts. Next, insert the shaker Rod into the bracket
and attach to the shaker grate bar using the 1/4-20 x 1"
Hex Bolt and a 1/4-20 Lock Nut. The bolt and nut retaining
the shaker bar and rod should be left loose to allow free
movement of the grates.
(1) Shaker Rod
(1) Shaker Bracket
(1) 1/4-20 x 1" Hex Bolt
(2) 1/4-20 x 3/4" Hex Bolt
(3) 1/4-20 Lock Nut

SMOKE CURTAIN

Using two 1/4-20 x 1-1/4" Carriage bolts, the smoke cur-
tain clips and two nuts, attach the smoke curtain in place
above the Fuel Feed Door as shown below. After installa-
tion, the smoke curtain should swing freely back into the
furnace.
(1) Smoke Curtain
(2) 1/4-20 x 1-1/4 Carriage Bolt
1/4-20 NUT
SMOKE CURTAIN
CLIP
BRACKET
(2) Smoke Curtain Clips
(2) 1/4-20 Kep Nut
1/4-20 x 1-1/4
CARRIAGE BOLT
SMOKE CURTAIN
NUT
BOLT
SMOKE CURTAIN
CLIP
SMOKE CURTAIN
FRONT
USSC