Table of Contents
Advertisement
Note: After carrying out the above operations, close the holes on
the unit with the special plastic caps.
B.1.5 ELECTRICAL CONNECTION
When making the electrical connection, carefully comply with
the information on the dataplate.
The appliance works on 120V/1ph/60Hz.
CAUTION:
Connection to the electrical mains must be carried out in
accordance with current regulations and the standards re-
quired by the National Electric Code (NEC), known as NFPA 70.
Please check:
Connection to the main power must be carried out in accord-
ance with binding rules and standards.
Before connecting, make sure that:
- The line cord has an efficient grounding connection and the
main power frequency corresponds to that stated on the data
plate. If you have doubts on the efficiency of the grounding
connection have the circuit checked by a qualified technician.
- The appliance must be connected to the main power with a
permanent connection.
- In order to protect the appliance from possible overloads or
short-circuits, a fused disconnect switch or a main circuit
breaker (customer furnished) MUST be installed in the elec-
tric supply line for the appliance. It is recommended that this
switch/circuit breaker have lockout/tagout capability. Before
making any electrical connections to this appliance, check
that the power supply is adequate for the voltage, amperage,
and phase requirements on the rating plate. The customer
also must provide a grounded electrical line cord of suitable
capacity for the input specified on the data plate.
- After making the connection and with the appliance running,
check that the rated level does not fluctuate by ± 10%.
The connection must be made with cable of a suitable
amperage and voltage.
The manufacturer will accept no liability for any damage or
injury resulting from the violation of the above rules or of the
current electrical safety standards in the country where the
appliance is used.
B.1.6 WATER CONNECTION
The machine has a drainage outlet where any liquids in the
chamber collect for drainage.
Connect the chamber drain outlet "C" (only for refrigerator
models), to be found on the bottom of the appliance and closed
with a plug, to a drain.
The drain outlet diameter is "0.69" / 17.5 mm"; it is therefore
advisable to connect it to a drain pipe of "0.69" / 17.5 mm".
Note: the drain must be siphoned to an open drain in order to
prevent any back-flow from the sewage system from reaching
the piping inside the chamber.
C.1 OPERATIONS and USER
INSTRUCTIONS
C.1.1 CONTROL PANELS (refer to fig.1/2/3/4)
C.1.1.1 "Refrigerator" version control panel
1
2a 3a 4
1
2
3
CATEGORY
HUM
HIGH
4
ACCESS TO
HIGH HUM.
FOOD CATEGORIES
ON/OFF
2
1 - Access to Food Categories button
2 - High humidity ON/OFF button
2a - High humidity indicator light
3 - Service alarms button
3a - Service alarms indicator light
4 - Manual defrost / UP button
5 - Set temperature / Category selection / DOWN button
6 - HACCP alarms button
7 - Display
8 - Compressor status indicator light
9 - Power supply status indicator light
10 - Power ON/OFF button
C.1.1.2 "Freezer" version control panel
1
1
2
CATEGORY
ACCESS TO
FOOD CATEGORIES
1 - Access to Food Categories button
2 - Service alarms button
2a - Service alarms indicator light
3 - Manual defrost / UP button
4 - Set temperature / Category selection / DOWN button
5 - HACCP alarms button
6 - Display
7 - Compressor status indicator light
8 - Power supply status indicator light
9 - Power ON/OFF button
C.1.2 INITIAL SWITCH-ON AND TEMPERATURE ADJUSTMENT
The appliance features an ON/OFF switch for activating it.
Turn on the appliance by pressing the ON/OFF button:
43
7
8
9
MANUAL
COMPRESSOR
POWER SUPPLY
DEFROST
STATUS
STATUS
%
SET
HACCP
SERVICE
TEMPERATURE/
HACCP
POWER ON/OFF
ALARMS
CATEGORY
ALARMS
SELECTION
PRINT
7 DAYS
REPORT
3
5
6
2a 3
6
7
8
MANUAL
COMPRESSOR
POWER SUPPLY
DEFROST
STATUS
STATUS
SET
HACCP
SERVICE
TEMPERATURE/
HACCP
POWER ON/OFF
ALARMS
CATEGORY
ALARMS
SELECTION
PRINT
7 DAYS
REPORT
2
4
5
10
9
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
