1. Manuals
  2. Brands
  3. Marksman Manuals
  4. Car Alarm
  5. Extreme X3
  6. Installation and owner's manual

Marksman Extreme X3 Installation And Owner's Manual

Extreme series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Installation
and Owner's
Manual
Model: X3
For Technical Assistance, please call (800) 638-3600,
or visit www.magnadyne.com
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's authority to operate the equipment.

Advertisement

Table of Contents
loading

Related Manuals for Marksman Extreme X3

Summary of Contents for Marksman Extreme X3

  • Page 1 Installation and Owner’s Manual Model: X3 For Technical Assistance, please call (800) 638-3600, or visit www.magnadyne.com This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.

  • Page 2: Table Of Contents

    Table of Contents Component Installation ..............2 Wiring White 12-Pin Main Harness .

  • Page 3: Wiring

    Wiring Harness Quick Reference HC4 12-Pin Main Harness Yellow +12VDC Ignition Input Green (-) Common Door Pin Input Blue (-) Hood / Trunk / Auxiliary Trigger Input Violet (+) Common Door Pin Input Orange (-) Ground when Armed Output Open No Connection Red/White (-) 300mA Programmable Channel 3 (Trunk) Output Black...
  • Page 4 Wiring (continued) Red/White Wire: (-) 300mA Programmable Channel 3 Output (Default Trunk Release) The Red/White wire is typically used to release the power trunk by remote. An additional relay is usually required as shown in the diagram below. This wire can also be programmed for Domelight Supervision Control or 2nd unlock function (See Alarm Feature Programming to change the setting) Output to Power Trunk Switch Red/White Wire...

  • Page 5: Black 3-Pin Door Lock Harness

    Wiring (continued) HC3: Black 3-Pin Door Lock Harness Blue Wire: (-) Door Unlock Control Connect the Blue wire to the unlock wire from the door lock switch. If the door locking system is not a (-) trigger system, additional relays will be required. Green Wire: (-) Door Lock Control Connect the Green wire to the lock wire from the door lock switch.

  • Page 6: Programming The Transmitter

    Optional Wiring Diagrams Red/White Wire: (When programmed for (-) Domelight Supervision Output) When Programmed for this function, the Red/White wire provides a (-) output to turn on the vehicles interior light when the alarm has been disarmed. The domelight will stay on for 30 seconds unless the ignition key is Output to Dome Light (+ or -) Red/White Wire To Constant +12 Volts...

  • Page 7: Alarm Feature Programming

    Programming the Transmitter Step 3 Step 5: Step 4 Exit Program Mode Press the “Lock” button on the first Repeat for each additional When finished, turn Off the ignition transmitter until you hear a transmitter. key or wait for 15 seconds to get out confirmation chirp/beep.

  • Page 8: Shock Sensor Testing And Adjustment

    Alarm Feature Programming (continued) Press TX Button Press TX Button Press TX Button Press TX Button Press LED Flash/ Valet One Chirp Chirp Two Chirps Three Chirps Switch (Default Setting) O “ ” f f O “ ” n Automatic Arming Automatic Arming Manual Arming without Door Locking...

  • Page 9: Owners Manual

    Shock Sensor Testing and Adjustment Step 6 Step 4 Step 5 Decrease Increase 1. Press and hold the LOCK and 1. Press the LOCK button to To exit the shock sensor test mode, UNLOCK buttons together for 2 increase sensitivity by 1 step turn ignition “On”...

  • Page 10: Dual-Zone Shock Sensor

    Owners Manual (Continued) Button Function: Transmitter Button System Function / Remark Action Press and Release Arm/Lock Doors Press Twice Arm/Lock Doors + Delete Shock Sensor (2nd Long Beep) Press and Release Progressive Car Finder (Functions 30 Seconds After Armed) Press and Release Disarm/Un-Lock Doors Press and Hold for 1.5 Seconds Channel 3 Activation (Release Trunk as Default)
  • Page 11 Owners Manual (Continued) F. Manual Disarming “Unlock” 1. Press the “Unlock” button on the transmitter. 2. The siren will chirp twice and parking lights will flash twice indicating that the security system is now disarmed. The vehicle doors will unlock disarming when interfaced with the security system. Tamper Disarming: If alarm is triggered upon disarming the system, the siren chips 4 times and the parking lights flash 3 times.

  • Page 12: Anti Car-Jacking

    K. Anti Car-Jacking (Manual Activation) Warning: If you don’t need this alarm system’s car-jacking function to be “On”, set it to “Off”. The default car-jacking setting is “Off” (see Feature No. 6 on programming chart). Pressing and holding the “Lock” and “Unlock” button on the transmitter for 1 second while the vehicle’s ignition is “On”...

Table of Contents