Panasonic BT-LH1850 Operating Instructions Manual page 28

Main menu
(continued)
Sub menu Settings
POWER ON SETUP LAST
FACTORY
USER1
USER2
USER3
USER4
USER5
COLOR SPACE SMPTE-C
EBU
ITU-709
POWER DOWN OFF
ON
POWER SAVE OFF
MODE ON
CALIBRATION
▼
*
4
Factory default setting for the BT-LH1850P.
*
5
Factory default setting for the BT-LH1850E.
*
6
ITU-709 indicates the ITU-R BT.709 standard.
„ INPUT NAME SETUP
„
The "INPUT NAME SETUP" function allows you to change the names of the input lines (VIDEO, SDI1, SDI2, HDMI, DVI-I (YP
RGB-COMP./DVI-VIDEO/DVI-COMP.), INT-SG) that are displayed in status or other indications.
1.
Turn the rotary knob in the "SYSTEM CONFIG" menu to
select the "INPUT NAME SETUP" submenu and press the
rotary knob.
2.
Turn the rotary knob to select the name of the input line
you want to change and press the rotary knob.
[INPUT NAME SETUP]
VIDEO VIDEO
SDI1 SDI1
SDI2 SDI2
HDMI HDMI
YP P YP P
B R B
RGB-COMP. RGB-COMP.
DVI-VIDEO DVI-VIDEO
DVI-COMP. DVI-COMP.
INT-SG INT-SG
MENU EXIT SEL. ENTER
3.
Turn the rotary knob to select the characters you want to
change * 7 and press the rotary knob to enter them.
• The selected characters are highlighted and change to italics
when entered.
[INPUT NAME SETUP]
VIDEO VIDEO
SDI1 SDI1
SDI2 DI2
HDMI HDMI
YP P YP P
B R B
RGB-COMP. RGB-COMP.
DVI-VIDEO DVI-VIDEO
DVI-COMP. DVI-COMP.
INT-SG INT-SG
MENU EXIT SEL. ENTER
*
7
The "B" and "R" in YP
B
„ CALIBRATION
„
The CALIBRATION function in this unit measures LCD panel characteristics from low to high brightness values and internal monitor
processing handles CALIBRATION.
CALIBRATION does not rely on image quality settings since internal signals are used for a calibration. CALIBRATION in this unit is
made at D65 color temperature and other color temperatures are results calculated automatically from this value.
28
Selects the settings used when the power is turned on.
<LAST>
<FACTORY> Starts up using the factory defaults.
<USER1 - 5> Starts up using USER registered settings.
*
4 Sets the studio standard color space.
* 5
*
6
Determines whether or not the power will be turned off (power down) when there is no
signal input and the unit has been idle for a certain period of time.
<OFF> The unit is not powered down.
<ON> The unit is powered down.
Sets the power save mode.
<OFF> POWER SAVE MODE is not engaged.
<ON> The backlight dims when no signal (NO SIGNAL) is input for 60 seconds or longer.
Signal input or menu operation will return the backlight to its normal brightness.
Connect Display Color Analyzer CA-310 and then perform calibration. This also allows you
to restore the calibration data to the factory preset setting values. (→pages 28 to 30)
R
RETURN RETURN
re
set
R
RETURN RETURN
P cannot be selected.
R
Description
Starts in the mode used when the power was last turned off.
4.
Turn the rotary knob to enter the characters and press the
rotary knob to confirm them.
• After entering all display characters, select
rotary knob to confirm them.
[INPUT NAME SETUP]
VIDEO
SDI1
SDI2
HDMI
YP P
B R
RGB-COMP.
DVI-VIDEO
DVI-COMP.
INT-SG
MENU EXIT
• Selecting
re
set
tered characters and returns them to their default values.
• To cancel a setting, press RETURN before pressing the ro-
tary knob to set the display characters.
VIDEO
SDI1
re
AAAA
set
HDMI
YP P
B R
RGB-COMP.
DVI-VIDEO
DVI-COMP.
INT-SG
SEL. ENTER RETURN RETURN
and pressing the rotary knob cancels the en-
P /
B R
and press the