Zenith L26W56S Installation And Operating Manual page 47

Installer Menu
Detailed Descriptions of Installer Menu Items
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the Channel-Time display, Channel-Time display
will not appear.
Set to 0 to enable the Channel-Time display.
069 - EN. CH-T COL. (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
070 - FOR. CH-TIME (Channel-Time Display Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow
1 = Red 4 = Blue
2 = Green 5 = Violet
NOTE: If foreground and background colors are the same, menu
background is transparent.
071 - BCK. CH-TIME (Channel-Time Display Background Color)
Set according to Color Chart.
0 = Black 3 = Yellow
1 = Red 4 = Blue
2 = Green 5 = Violet
NOTE: If foreground and background colors are the same, menu
background is transparent.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, "NOT
AVAILABLE" message is displayed when directly accessing a channel
not in the channel scan list available in memory.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of M.P.I. communication occurs, TV automatically
tunes to the specified Start Channel.
078 - UPN MSB (UPN Most Significant Byte)
User programmable number, most significant byte readable by M.P.I.
command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
M.P.I. command. Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
M.P.I. command. Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by M.P.I.
command. Not linked to serial number.
6 = Cyan
7 = White
6 = Cyan
7 = White
082 - CHKSM ERROR (Checksum Error)
Enforces rigid M.P.I. checksum validation.
Set to 1 for validation.
Set to 0 to disable (does not check checksum on M.P.I. async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing M.P.I. timing requirements to be compatible with PC
based Windows controlled systems, range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]).
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent by
disabling the blocking hours function.
Set to 1 to install Parental Control restrictions permanently.
Set to 0 for user-specified hours control of blocking schemes.
087 - REAR RGB EN. (Rear RGB1 Enable)
Controls access to rear RGB1 input on display panel.
Set to 1 to enable RGB1 input for DTV. Set to 0 to disable RGB1
input.
NOTE: The setting above is ignored if Installer item 093 RJP
AVAILABLE, is set to 1. Then 087 - REAR RGB EN. above, always
resets itself to PC (1) -- regardless of what value appears for item
087 on the Installer menu.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
090 - KEY LOCK
If set to 1, display panel keyboard is locked out, not available to end
user. IR receiver remains functional.
091 - YPrPb2 EN. (Rear Component Video 2 Enable)
Set to 1 to enable display panel Component 2 input.
Set to 0 to disable display panel Component 2 input.
092 - RGB2 ENABLE (Red-Green-Blue 2 Enable)
Set to 1 to enable display panel Video 3 input for Composite Video,
set to 2 to enable for S-Video. Set to 0 to disable display panel
Video 3 input.
093 - RJP AVAILABLE
Set to 1, remote jack pack is available.
Set to 0, remote jack pack is not available.
NOTE: This item can not be set to 1 if item 040 AUTO CAMPORT is
set to 1.
(Continued on next page)
P A G E 4 7