Multichannel Setup Sub-Menu - Integra DTR-8.2 Instruction Manual

Input Setup
a. Digital Input
This setting tells the DTR-8.2 which input source button on the front
panel is connected with which digital input jack on the rear panel. To
perform this setting, you must first select a digital input source at the
front panel and then set the name of the digital input jack it is
connected to here.
For example, if the input source selected at the front panel is CD and
the compact disc player is connected to DIGITAL INPUT (OPT) 1,
then select "OPT1" here. If the input source selected is not connected
to a digital input, then select "----."
OPT1-4: Connect your digital components to any of the
DIGITAL INPUT (OPT) terminals 1 through 4.
COAX1-3: Connect your digital components to any of the
DIGITAL INPUT (COAX) terminals 1 through 3.
----: Select if the input source is not from a digital input jack.
b. Digital Format
Sets the digital signal type to which priority is given during signal
detection at the selected digital terminal.
The default setting is "All." If "----" is selected for this input source
at the Digital Input setting, then this setting will not appear.
Although you can use this default setting as is, you may change it as
desired depending on the input signal format (e.g., if you know that
you will always be listening to a certain input signal format from a
particular input source).
All: Select for automatic detection of the input signal format.
The input signal format (Dolby Digital, DTS, PCM or Analog)
used by the selected input source is detected automatically to
execute the required decoding process.
DTS: Select for DTS signal processing. The decoding process is
executed only when DTS signals are input.
PCM: Select for PCM signal processing. The decoding process
is executed only when PCM signals are input.
Notes:
• If "All" is selected and a compact disc or LD is fast-forwarded
during playback, decoded PCM signals may produce a skipping
sound. In such cases, change the setting to "PCM."
• If a DTS signal is not input when "DTS" is selected, the DTR-
8.2 does not automatically switch to analog output even if
"Auto" is selected with the Audio Selector button.
Notes on DTS:
• If you play a CD or LD that supports DTS when the "PCM"
setting is selected on the DTR-8.2, the DTS encoded signal will
not be decoded and noise will be output. This noise could
damage the amplifier and speakers. Therefore, be sure to select
"All" or "DTS" and use the digital input jacks (OPTICAL or
COAXIAL) to connect the DTS source.
• If you play a CD or LD that supports DTS when "All" is
selected, you may hear a noise for a short while until the DTS
decoder recognizes the DTS-encoded signal and starts operating.
This is not a malfunction.
• If you press the pause or skip button on the player while playing
a DTS source, a short noise may be heard. This is not a
malfunction. In such cases, try playing the source in the "DTS"
selected.
• The DTS indicator on the DTR-8.2 lights while a DTS source is
played. When playback finishes and the DTS signal
transmission stops, the DTR-8.2 remains in DTS mode and the
DTS indicator remains lit. This prevents noise when you operate
the pause or skip button on the player. Therefore, if the source is
immediately switched from DTS to PCM, the PCM signal may
not be played. In this case, stop the playback of the source on the
player for about three seconds and then resume playback.
• You may not be able to play some DTS source signals from
certain CD players and LD players even if you connect the
player to the DTR-8.2 digitally. This is because the digital signal
has been processed (such as the output level, sampling
frequency, or frequency response) and the DTR-8.2 cannot
recognize the signal as DTS data. Therefore you may hear noise
when you play a DTS source while processing the signal.
• The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, TAPE
OUT, and ZONE 2 OUT, output analog audio signals. Do not
record from CDs or LDs that support DTS using these outputs. If
you do, the DTS-encoded signal will be recorded as noise.
• If a compact disc or LD encoded in the DTS format is played
back with "PCM" selected, only noise will be produced. Always
select "All" or "DTS" when playing back DTS-encoded sources.

2-2. Multichannel Setup sub-menu

This setting is normally set to "No," and only needs to be changed to
"Yes" if a DVD player, MPEG decoder, or other component that has
a multi channel port is connected to the MULTI CHANNEL INPUT
port for 5.1-channel, 6.1-channel, or 7.1-channel audio. For
example, if a DVD player is connected to the MULTI CHANNEL
INPUT port, then select DVD at the front panel as the input source,
bring up this sub-menu, and select "Yes" for the Multichannel
setting. You can only select Multichannel with the Audio Selector
button when "Yes" is selected here.
Advanced Menu
2.Input Setup
Input:DVD
2-2.Multichannel Setup
Input:DVD
a.Multichannel
Input source selected
CD
PHONO
FM
AM
TAPE
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
Note:
When playing a device that is actually connected to the MULTI
CHANNEL INPUT terminal, select Multichannel with the Audio
Selector button.
:Yes
Quit:|SETUP|
Multichannel
No
No
No
No
No
Yes
No
No
No
No
No
37