Adjusting The Detail Of Audio Control; Audio Setup - Kenwood KDC-X8006U Instruction Manual

General features

Adjusting the detail of Audio Control

Among the Basic Audio items, you can adjust the Bass
level, Middle level, and Treble level in detail.
1
Select the Basic Audio item
Select the desired item to be set in detail from
followings;
• Bass level
• Middle level
• Treble level
For how to select Basic Audio items, see <Audio
Control> (page 7).
2
Enter Detail adjustment mode of Audio
Control
Press the [VOL] knob for at least 1 second.
3
Select the Detail Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
4
Adjust the Detail Audio item
Turn the [VOL] knob.
Bass level
Adjustment Item Display
Bass Center Frequency "BASS FRQ"
Bass Q Factor "BASS Q FACTOR" 1.00/1.25/1.50/2.00
Bass Extend "BASS EXT"
Middle level
Adjustment Item Display
Middle Center Frequency "MIDDLE FRQ"
Middle Q Factor "MIDDLE Q FACTOR" 1.00/2.00
Treble level
Adjustment Item Display
Treble Center Frequency "TREBLE FRQ"
5
Exit the Detail Audio Control mode
Press the [VOL] knob for at least 1 second.
⁄
• When you set the Bass Extend to ON, low frequency
response is extended by 20%.
• You can exit the Audio Control mode at anytime by
pressing any button except for [VOL], [0] and [ATT]
buttons.
|
8
English

Audio Setup

Setting the Sound system, such as Cross over
Network.
1
2
3
4
Range
40/50/60/70/80/100/
120/150 Hz
OFF/ON
Range
0.5/1.0/1.5/2.0 kHz
Range
10.0/12.5/15.0/17.5 kHz
5
Select the source to adjust
Press the [SRC] button.
Refer to <Selecting the Source> (page 6).
Enter Audio Setup mode
Press the [VOL] knob for at least 1 second.
Select the Audio Setup item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
Setup the Audio item
Turn the [VOL] knob.
Adjustment Item Display
Front High Pass Filter "HPF-F Fc"
Rear High Pass Filter "HPF-R Fc"
Low Pass Filter "LPF-SW Fc" 50/60/80/100/120/Through Hz
Subwoofer Phase "SW PHASE" Reverse (180°)/ Normal (0°)
Volume offset "VOL-OFFSET" –8 — ±0 (AUX: -8— +8)
Loudness "LOUD"
Dual Zone System "2 ZONE"
⁄
• Volume offset: Sets each source's volume as a difference
from the basic volume.
• Loudness: Compensates for low and high tones
during low volume. (Only the low tone is
compensated for when the tuner is selected
as a source.)
• Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by <Dual Zone
System Setting> (page 27).
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [VOL] knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 7).
- The Audio Control has no effect on sub source.
• You can use the Dual Zone System with the internal
auxiliary input.
Exit Audio Setup mode
Press the [VOL] knob for at least 1 second.
Range
Through/40/60/80/100/120/
150/180/220 Hz
Through/40/60/80/100/120/
150/180/220 Hz
OFF/ON
OFF/ON