Remote Control; General - Dynex DX-24LD230A12 User Manual

38
DX-24LD230A12
Problem Solution
The picture has a • A few bright or dark spots on an LCD
few bright or dark screen is normal. It does not affect the
spots. operation of this TV/DVD combo.
Good picture, but no • Increase the volume.
sound. • Make sure that the sound is not muted.
• Make sure that the correct audio mode
is selected.
• Make sure that the audio cables are
connected correctly and securely to
the back of your TV/DVD combo.
• Make sure that the antenna or cable TV
is connected correctly and securely.
See "Connecting a cable or satellite
box" on page 8 or "Connecting an
antenna or cable TV (no box)" on
page 11.
• If you are using an antenna, the digital
channel signal may be low. To check
the digital channel signal strength, see
"Checking the digital signal strength"
on page 26.
• The audio cable(s) you are using may
be bad. Try a new set.
Poor picture • Make sure that the room is not too
bright. Light reflecting off the screen
can make the picture difficult to see.
• If an S-VHS camera or a camcorder is
connected while another connected
device is turned on, the picture may be
poor. Turn off one or more devices.
Good sound but • Adjust the contrast, color, and
poor color brightness settings.
Audio noise • Other devices (for example, surround
sound receiver, external speakers, fans,
or hair dryers) may be interfering with
your TV. Try turning off one device at a
time to determine which device is
causing interference. Once you have
determined which device is causing
interference, move it further from the
TV/DVD combo to eliminate the
interference.
No output from one • Adjust the audio balance. See
of the speakers "Adjusting the sound settings" on
page 23.
• Make sure that the audio cables are
connected correctly and securely to
the back of your TV/DVD combo.
After images appear • Do not display a still image, such as a
logo, game, or computer image, for an
extended period of time. This can
cause a permanent after-image to be
burned into the screen. This type of
damage is not covered by your
warranty.

Remote control

Problem Solution
Remote control • Make sure that the power cord is
does not work. correctly connected to your TV/DVD
combo and a power outlet.
• Make sure that there are no
obstructions between the remote
control and the remote control sensor
on the front of the TV/DVD combo.
• Point the remote control directly at the
remote control sensor on your TV/DVD
combo. For the location of the remote
control sensor, see "Front" on page 5.
• Make sure that the batteries are
installed correctly. See "Installing
remote control batteries" on page 15.
• Replace dead batteries with new ones.
See "Installing remote control
batteries" on page 15.
Trouble • See instructions and a table of
programming your common codes in "Programming a
existing universal different universal remote control" on
remote control. page 41.
• Codes are subject to change. For up to
date codes, go to
www.dynexproducts.com.
• Replace dead batteries with new ones.
See "Installing remote control
batteries" on page 15.
• Refer to the User Guide that
accompanied your universal remote
control and contact the manufacturer
if problems persist.

General

Problem Solution
No power • Make sure that the power cord is
correctly connected to your TV/DVD
combo and a power outlet.
• Unplug the power cord, wait 60
seconds, then plug the cord back in
and turn on your TV/DVD combo.
• Other devices (for example, surround
sound receiver, external speakers, fans,
or hair dryers) may be interfering with
your TV/DVD combo. Try turning off
one device at a time to determine
which device is causing interference.
Once you have determined which
device is causing interference, move it
further from the TV/DVD combo to
eliminate the interference.
"No signal" error • Press INPUT and make sure that you
message is have selected the correct input for the
displayed device or service you are trying to use.
• If you are using a cable or satellite box,
use the remote that came with that
box to change channels.
After Auto • Reception can vary by channel
Channel Search, depending on the broadcast power
there are no level of a given station. Contact your
channels cable or satellite TV provider.
• Make sure the antenna or
cable/satellite TV is connected
securely to your TV/DVD combo.
• Try replacing the cable between the
antenna/cable or cable/satellite box
and your TV/DVD combo.
Troubleshooting