Remote Control; General; Disc Playback - Dynex DX-19LD150A11 Important Information Manual

Troubleshooting
Problem Solution
No output from one • Adjust the audio balance. See "Adjusting
of the speakers the sound settings" in the User Guide.
• Make sure that the audio cables are
connected correctly and securely to the
back of your TV/DVD combo.
After images appear • Do not display a still image, such as a logo,
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen.
This type of damage is not covered by your
warranty.

Remote control

Problem Solution
Remote control • Make sure that the power cord is correctly
does not work. connected to your TV/DVD combo and a
power outlet.
• Make sure that there are no obstructions
between the remote control and the
remote control sensor on the front of the
TV/DVD combo.
• Point the remote control directly at the
remote control sensor on your TV/DVD
combo. For the location of the remote
control sensor, see "Front" in the User
Guide.
• Make sure that the batteries are installed
correctly. See "Installing remote control
batteries" in the User Guide.
• Replace dead batteries with new ones. See
"Installing remote control batteries" in the
User Guide.
Trouble • See instructions and a table of common
programming your codes in "Programming a different universal
existing universal remote control" in the User Guide.
remote control. • Codes are subject to change. For up to date
codes, go to www.dynexproducts.com.
• Replace dead batteries with new ones. See
"Installing remote control batteries" in the
User Guide.
• Refer to the User Guide that accompanied
your universal remote control and contact
the manufacturer if problems persist.

General

Problem Solution
No power • Make sure that the power cord is correctly
connected to your TV/DVD combo and a
power outlet.
• Unplug the power cord, wait 60 seconds, then
plug the cord back in and turn on your TV/DVD
combo.
• Other devices (for example, surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV/DVD combo.
Try turning off one device at a time to
determine which device is causing
interference. Once you have determined
which device is causing interference, move it
further from the TV/DVD combo to eliminate
the interference.
"No signal" error • Press INPUT and make sure that you have
message is selected the correct input for the device or
displayed service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
Problem Solution
After Auto • Reception can vary by channel depending on
Channel Search, the broadcast power level of a given station.
there are no Contact your cable or satellite TV provider.
channels • Make sure the antenna or cable/satellite TV is
connected securely to your TV/DVD combo.
• Try replacing the cable between the
antenna/cable or cable/satellite box and your
TV/DVD combo.
One or more • Make sure that the channels are not blocked.
channels do not See "Setting parental control levels" in the
display. User Guide.
• Make sure that the channels are not hidden.
The channel may have been deleted from the
channel list. You can tune to the channel by
pressing the number buttons or you can add
the channel back to the channel list. See
"Hiding channels" in the User Guide.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure you have the correct input selected
to view channels from the cable or satellite
box.
• If you are using an antenna, the digital channel
signal may be low. To check the digital
channel signal strength, see "Checking the
digital signal strength" in the User Guide.
Password is lost. • Enter 9999 to access parental controls, then
set a new password. See "Setting or changing
the password" in the User Guide.
Some settings • If a setting is grayed, the setting is not
cannot be available in the current video input mode.
accessed.
TV/DVD combo • When the TV/DVD combo is in use, the
cabinet creaks. temperature rises naturally and may cause the
cabinet to expand or contract which can cause
a creaking noise. This is not a malfunction.
Control buttons • Make sure that the Button Lock option is set
do not work to Off. See "Locking control buttons" in the
User Guide.
• Unplug the power cord, wait a few seconds,
then plug the cord back in and turn on your
TV/DVD combo.
TV/DVD combo • Make sure that the sleep timer is not turned
keeps turning off on. See "Setting the sleep timer" in the User
Guide.

Disc playback

Problem Solution
Playback does not • No disc is loaded. Insert your disc into the
start. disc slot.
• The disc may be dirty. Clean the disc.
• The disc is not supported. See the User
Guide for a list of compatible disc formats.
No picture. • The TV/DVD combo is not in DVD mode.
Press INPUT and select DVD as the input
source.
No sound. • If an external speaker is connected, check its
volume control.
Picture distortion • The picture will be distorted occasionally.
during fast This is not a malfunction.
reverse/forward
playback.
Playback features • The playback features such as stopping,
failure. skipping, or repeat play are not applicable to
all discs.
5
DX-19LD150A11