Sound Adjustments; Basic Adjustment Items; Operating Procedure - JVC RXD212B - 110 Watts X 7 Receiver Instructions Manual

Sound adjustments

You can make sound adjustment to your preference after
completing basic setting.

Basic adjustment items

You can adjust the following items. See pages in parentheses for
details.
• You cannot select the items which are not available with the
current setting.
Items To do
SUBWFR LVL* 1 Adjust the subwoofer output level. (27)
1 2
FRONT L LVL* * Adjust the left front speaker output level. (27)
FRONT R LVL* 1 * 2 Adjust the right front speaker output level. (27)
1 2
CENTER LVL* * Adjust the center speaker output level. (27)
SURR L LVL* 1 * 2 Adjust the left surround speaker output level.
(27)
SURR R LVL* 1 * 2 Adjust the right surround speaker output
level. (27)
S BACK LVL* 1 * 2 Adjust the surround back speaker output
level. (27)
S BACK L LVL* 1 * 2 Adjust the left surround back speaker output
level. (27)
1 2
S BACK R LVL* * Adjust the right surround back speaker
output level. (27)
D EQ 63Hz* 1 Adjust the equalization pattern of each
D EQ 250Hz* 1 band. (27)
D EQ 1kHz* 1
D EQ 4kHz* 1
D EQ 16kHz* 1
BASS BOOST* 1 Boost the bass level. (28)
INPUT ATT Attenuate the input level of analog source. (28)
EFFECT* 1 Adjust the effect level. (28)
ROOM SIZE Select the room size for your virtual listening
room. (28)
LIVENESS Select the liveness level for your virtual
listening room. (28)
PANORAMA Add "wraparound" sound effect with side-
wall image. (28)
CENTER WIDTH Adjust the center channel localization
between the center speaker and the left/
right speakers. (29)
DIMENSION Adjust sound localization pattern. (29)
CENTER GAIN Adjust the sound localization of the center
channel. (29)
CENTER TONE* 1 Make the center tone soft or sharp. (29)
CENTER ALIGN Align the vertical localization of the center
channel signals. (29)
1
* You can also use the remote control for the adjustment.
2
* If you have used Quick Speaker Setup on page 20, these
settings are not required.
26

Operating procedure

1,7
On the front panel ONLY:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Ex.: When adjusting subwoofer output level.
1
Press ADJUST.
MULTI JOG now works for the sound adjustment.
2
Turn MULTI JOG until the item you want to
adjust appears on the display.
• As you turn MULTI JOG, the adjustment items change as
follows:
ANALOG
L R
S.WFR
SUBWFR LVL
FRONT R LVL
SURR L LVL
S BACK LVL
S BACK R LVL
D EQ 250Hz
D EQ 4kHz
BASS BOOST
EFFECT
LIVENESS
CENTER WIDTH
CENTER GAIN
CENTER ALIGN
3
Press SET.
The current setting for the selected item appears.
ANALOG
L R
S.WFR
4
Turn MULTI JOG to adjust the selected item.
ANALOG
L R
S.WFR
Your adjustment is stored.
5
Press SET.
6
Repeat steps 2 to 5 to adjust other items if
necessary.
7
Press ADJUST.
The source indication resumes on the display.
3,5 2,4
FRONT L LVL
CENTER LVL
SURR R LVL
S BACK L LVL
D EQ 63Hz
D EQ 1kHz
D EQ 16kHz
INPUT ATT
ROOM SIZE
PANORAMA
DIMENSION
CENTER TONE
(Back to the beginning)
–10
0 +10