Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dual XDVD1002CM
Summary of Contents for Dual XDVD1002CM
- Page 1 XDVD1002CM INSTALLATION/OWNER'S MANUAL...
-
Page 2: Table Of Contents
Please read all instructions carefully before attempting to install or operate. Due to its technical nature, it is highly recommended that your DUAL XDVD1002CM is installed by a professional installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only. -
Page 3: Before You Begin
Do not use any screws except the ones provided. If you experience problems during installation, consult your nearest DUAL dealer. To clean the monitor, wipe only with a dry silicone cloth or soft cloth. Do not use a stiff cloth, or volatile solvents such as paint thinner and alcohol. -
Page 4: Package Contents
XDVD1002CM Contents Main Unit Wiring Harness and Hardware Recommended Tools and Equipment • Upholstery hook tool (for removal of panels, if necessary) • #1 and #2 Phillips screwdrivers • Utility knife, razor knife, or shears • Misc. electrical connectors (to connect to vehicle power source – requirement will vary form vehicle to vehicle) •... -
Page 5: Wiring Diagram
Some vehicles incorporate transistorized control of the dome light circuit, and may not support the additional current draw of the unit's dome lights. On these vehicles it may be necessary to connect the green wire (dome light trigger) to a door pin switch wire. XDVD1002CM INSTALLATION Wiring Diagram - Main Unit... -
Page 6: Mounting
XDVD1002CM Mounting INSTALLATION 1. Test fit the mounting bracket and unit on the ceiling of the vehicle, verify- ing that it is not going to interfere with the safe operation of the vehicle and is physically safe for the driver and passengers. -
Page 7: Control Locations
Power Source Select Chapter/Track Down Dome Light Switch Screen Release Aux1 Inputs XDVD1002CM OPERATION Control Locations - Main Unit Rear IR Sensor Motorized Disc Slot Front IR Sensor/Transmitter Chapter/Track Up Play/Pause Disc Eject... -
Page 8: Control Locations
XDVD1002CM Control Locations - Remote OPERATION Power Return Fast Reverse Enter Chapter/Track Down Root Menu Setup Menu Step Subtitle Dimmer Angle Shuffle Goto Video/Source Repeat LCD Screen Menu Program Screen Mode Screen Zoom FM Transmitter Title Repeat A-B Mute Audio... -
Page 9: General Operation
XDVD1002CM OPERATION General Operation To turn on the unit, press the power button on the main unit or on the remote. Press Power On/Off again to turn the unit off. Pressing the screen release lock will unlock the LCD screen, and it will drop down Monitor Open/Close slightly. -
Page 10: Setup Menu
XDVD1002CM General Operation - Setup Menu Selecting Sources - Main Unit Selecting Sources - Remote Volume Mute Display Display Mode Setup Menus General Setup Speaker Setup DIVX (R) Registration OPERATION Press SOURCE on the main unit to select between the following sources: AUX1 >... - Page 11 Select OP MODE from the AUDIO SETUP menu. Press to make selection. Press or to adjust (LINE OUT/RF REMOD). Select DUAL MONO from the AUDIO menu. Press to make selection. Press or to adjust (STERE/L-MONO/R-MONO/MIX-MONO).
-
Page 12: Dvd Operation
XDVD1002CM DVD Operation DVD Mode Insert Disc Eject Disc Selecting DVD Root Menu Stop/Start Play/Pause Chapter Select Direct Title/Chapter Select Direct Title/Time Select Fast Forward and Reverse Step (frame-by-frame) Repeat OPERATION Press SOURCE on the remote or the main unit to select DVD mode. - Page 13 XDVD1002CM OPERATION DVD Operation Press A-B on the remote for more than 2 seconds to set point “A”. Repeat A-B Press A-B for more than 2 seconds to set point “B”. The points between “A” and “B” will continually repeat.
-
Page 14: Cd Operation
XDVD1002CM CD Operation CD Mode Insert Disc Eject Disc Stop/Start Play/Pause Track Select Direct Time Select Fast Forward and Reverse Repeat Repeat A-B Program Mode Display Status OPERATION Press SOURCE on the remote or the main unit to select DVD mode. -
Page 15: Mp3 Operation
Display Status Additional MP3 information: Supports the Following Formats: CD-R/CD-RW Compatibility XDVD1002CM Additional MP3 Operation When an MP3 encoded disc is first inserted, SMART NAVI will show on screen. The disc will automatically begin playback. NOTE: It may take a few seconds for the unit to read disc. -
Page 16: Divx Operation
XDVD1002CM DivX Operation ® DivX Mode Selecting a File/Folder Begin Playback from ROOT Selecting Play Modes Random Display Status What is DivX? OPERATION When a DivX encoded disc is first inserted, playback will begin with the first file auto- matically, To access the SMART NAVI menu screen, stop playback by pressing the remote. -
Page 17: Warranty
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and work- manship for a period of one year from the date of the origi- nal purchase. -
Page 18: Troubleshooting
XDVD1002CM Troubleshooting Unit has no power at main unit Unit has power but no video Picture has occasional distortion Brightness unstable The DVD does not start playback Remote control not working Copyright Notes This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. -
Page 19: Specifications
XDVD1002CM OPERATION Specifications Player Signal-to-noise: >92dB Dynamic range: >85dB Frequency response: 20Hz-20kHz Panel size: 10.2” Diagonal measurement Monitor Format: Widescreen 16:9 View area: 8.74” x 5.24” (222 x 133 mm) Display system: Color TFT active matrix LCD View angle (up/down/left/right):... - Page 20 Dual Electronics Corp. 21318 64th Ave. South Kent, WA 98032 Toll Free: 1-866-382-5476 www.dualav.com ©2005 Dual Electronics Corp. All rights reserved. NSA0805-V01...