Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: Vehicle Identification Number
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
Page 6: Vehicle Modifications / Alterations
6 INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 7 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....9 Key-In-Ignition Reminder ....9 Sentry Key —...
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security Alarm System — If Equipped ..24 To Set The Alarm ..... .25 To Disarm The System .
Page 9: Things To Know Before Starting Your Vehicle 7
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith.
Page 10: 10 Things To Know Before Starting Your Vehicle
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE on the remaining transmitters will work. If the vehicle is shifted out of PARK, all the transmitter buttons are disabled for all keys. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Page 11 consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following:...
Page 12: Ignition And Steering Lock
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. IGNITION AND STEERING LOCK In the LOCK position, the steering and ignition systems are locked to provide anti-theft protection for your ve- hicle.
Page 13: Ignition Accessory Delay Feature
NOTE: The steering wheel will lock when the key is removed, and the steering wheel is turned around 115 degrees clockwise or 65 degrees counterclockwise from the center position. Ignition Accessory Delay Feature When the ignition is turned to OFF/LOCK position the accessory features on the vehicle will continue to operate for ten minutes or until the driver’s door is opened.
Page 14: Power Door Locks
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 15 Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
Page 16 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction.
Page 17: Child Protection Door Lock
2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confusing during this program- ming procedure). 3. Insert the key into the ignition. 4. Within 10 seconds, cycle the key from the OFF position to the ON position four times ending in the ON position (do not start the engine).
Page 18 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
Page 19: Remote Keyless Entry
REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
Page 20: To Lock The Doors And Liftgate
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob. NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm.
Page 21: Using The Panic Alarm
Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 6. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. Flash Lamps with Lock Programming 1.
Page 22: General Information
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
Page 23 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ).
Page 24: Battery Replacement
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement The recommended replacement battery is CR2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal.
Page 25: To Set The Alarm
To Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming.
Page 26: Liftgate
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNLOCK button or by inserting a programmed Sentry Key into the ignition and turning the key to the ON position. LIFTGATE Once unlocked, the liftgate can be opened or closed without using the key. To open the liftgate, pull out on the outside handle and lift.
Page 27: Windows
WINDOWS Power Windows THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 The control on the left front door has up-down switches that give you finger tip control of all four power win- dows. There is a single opening and closing switch on the passenger doors for passenger window control.
Page 28: Auto Down
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF.
Page 29: Lap/Shoulder Belts
window. If you will be carrying children too small for adult-size seat belts, your seat belts or the LATCH feature (refer to the Child Restraint section in this manual), can be used to hold infant and child restraint systems. Please pay close attention to the information in this section.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE freely with you under normal conditions. But in a colli- sion, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 31 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 plate and pull out the belt.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. •...
Page 33 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug.
Page 34: Adjustable Upper Shoulder Belt Anchorage
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best.
Page 35: Seat Belt Pretensioners
Automatic Locking Mode To convert from the normal emergency locking mode to the automatic locking mode, grasp the shoulder belt portion and pull all of the webbing out of the retractor. Allow some of the webbing to retract into the retractor, as the belt retracts you will hear a clicking sound to indicate the seat belt is now in the automatic locking mode.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
Page 37: Seat Belts And Pregnant Women
Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen.
Page 38: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbags
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
Page 39 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1.
Page 41 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classification System (OCS) for the Front Passenger Seat − Occupant Classification Module − Passenger Airbag Disable (PAD) Indicator Light − Weight Sensors How the Airbag System Works •...
Page 43 light either momentarily or continuously. A single chime will sound if the light comes on again after initial start WARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE a rear-facing infant seat. Relatively light objects like brief cases and grocery bags will also turn on the PAD Indicator Light. The PAD Indicator Light will be off when teenagers, most children and most children in forward-facing seats are in the front passenger seat.
Page 45 The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the PAD Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time.
Page 47 • The Occupant Classification Module (OCM) is lo- cated beneath the front passenger seat. The OCM classifies the occupant into categories based on the measurements made by the seat weight sensors. The OCM communicates with the Occupant Restraint Con- troller (ORC). The ORC uses the occupant category to determine whether the front passenger airbag should be turned off.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position every- one for the best interaction with the front airbag. If A Deployment Occurs The airbag system is designed to deploy the airbags when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front...
Page 49 WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly, replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well.
Page 50: Child Restraint
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 5 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
Page 51 Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult seat belt. Always check the child seat owner’s manual to ensure you have the right seat for your child.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the seat cushion while the child’s back is against the seatback, they need a belt-positioning booster seat.
Page 53 Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH - Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s second row seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle...
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Second Row Right Side Second Row Left Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint.
Page 57 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with either cinch-...
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to do something more. Disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position or use the locking clip provided with your child restraint.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Second Row Seat...
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints in Third Row Seating (If Equipped) The third seating row is not capable of installing child restraints that require the use of a tether strap. There are no tether anchor provisions for the third seating row in your vehicle, the hooks in the rear floor are not designed to withstand the forces that may occur during a crash.
Page 61 WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 62: Engine Break-In Recommendations
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Page 63: Safety Checks You Should Make Inside The Vehicle
• It may be necessary to sit in a parked vehicle with the engine running for more than a short period. If so, adjust your climate control system to force outside air into the vehicle. Set the blower at high speed and the controls in any position except OFF or RECIRC.
Page 64: Safety Checks You Should Make Outside The Vehicle
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle: Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressure.
Page 65 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......70 Inside Day/Night Mirror ....70 Automatic Dimming Mirror —...
Page 66 66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seats Manual Seat Recliners ...87 Manual Lumbar Support Adjustment — If Equipped ......88 Adjustable Head Restraints —...
Page 67 Headlights, Parking Lights, Panel Lights ..106 Illuminated Entry ..... 107 Daytime Running Lights (Canada Only) ..107 Lights-On Reminder .
Page 68 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reset Button ......121 Global Reset ......121 Step Button .
Page 69 Electrical Outlet Use With Engine Off (Battery Fed Configuration) ....136 Floor Console ......137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Floor Console Features .
Page 70: 70 Understanding The Features Of Your Vehicle
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck).
Page 71: Outside Mirrors
CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
Page 72: Electric Remote-Control Mirrors
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move.
Page 73: Illuminated Vanity Mirrors - If Equipped
WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror.
Page 74: Automatic Dimming Driver's Exterior Mirror - If Equipped
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Driver’s Exterior Mirror — If Equipped This mirror will automatically adjust for annoying light glare from vehicles behind you. This feature is controlled by the inside mirror and can be turned off by pressing the button at the base of the inside mirror.
Page 75 access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the “Operation” Section. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e.
Page 76: Operation
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Voice commands can be used in the operation of the UConnect™ system and to navigate through the UCon- nect™ menu structure. Voice commands should be given after each UConnect™ system prompt. You will be prompted for a specific command and then guided through the available options.
Page 77 • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 having the highest priority. You can connect up to seven cellular phones to your UConnect™ system and the priority allows the UConnect™...
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Next, enter the number designation (e.g. “Home”, “Work”, “Mobile”, or “Pager”). This will allow you to have multiple numbers for each phonebook entry. • Recite the phone number for the phonebook entry that you are adding.
Page 79 Delete Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt, say Phonebook Delete . • After you enter the phonebook delete menu, you will then be asked for the name of the phonebook entry that you wish to delete.
Page 80: Phone Call Features
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say Call . • The UConnect™ system will then prompt you as to number designation you wish to call.
Page 81 Putting a Call on Hold and Retrieving a Call from Hold To put a call on hold, press the ’Phone’ button until you hear a single beep which will indicate that the call has been placed on hold. To bring the call back from hold, press the ’Phone’...
Page 82: Advanced Phone Connectivity
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity Transferring an Active Call between the UConnect™ System and Your Cellular Phone The UConnect™ system allows ongoing calls to be trans- ferred to your cellular phone or to the UConnect™ system without terminating the call.
Page 83: Uconnect™ System Features
List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the Ready prompt, say Setup List Phones and the UConnect™ system will play the phone names of all paired cellular phones in order from highest prior- ity to lowest priority.
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
Page 85 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system. By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s stereo sys- tem.
Page 86: Seats
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Front Seat Manual Seat Adjustment The adjusting lever is at the front of the seat, near the floor. Lift the lever and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
Page 87: Front Seats Manual Seat Recliners
WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Front Seats Manual Seat Recliners The bucket seats are equipped with recliners.
Page 88: Manual Lumbar Support Adjustment - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment — If Equipped The manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support.
Page 89: Way Driver's Power Seat - If Equipped
8 - Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment.
Page 90: Front Heated Seats - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seats — If Equipped This feature heats the driver and front passenger seats. The controls for the front heated seats are located on the center of the instrument panel, below the climate con- trols.
Page 91: Second Row 40/20/40 Seat - Fold And Tumble
then the system will turn off. Thus, a maximum of four hours of operation until the system is reactivated. If the low heat setting is initially selected, the system will operate for two hours and then turn off. If the indicator lamp on the heated seat switch does not light when the switch is depressed or if heated seats does not operate, the system should be serviced by a qualified technician.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Raising the lever allows third row seat passengers to fold the seatbacks and release the latches when exiting the vehicle. Once the seatback is in a folded position continue raising the lever fully to release the cushion latches and tumble the seat.
Page 93: Third Row Seat Bench - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Third Row Seat Bench — If Equipped To Fold The Seats Folding the third seat occurs in two stages: the cushion is lifted and moved forward then the back is folded. Pull up and forward on either one of the 2 straps at the front of the cushion.
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flat Load Floor Unsnap the flipper panels on the third row seats and flip them forward on the back(s) of the second row seat(s).
Page 95 To Achieve Maximum Cargo Capacity Pull up the release handles and strap on the second row seats and fold the seat backs flat. Then fold the third row seat flat. Unsnap the flipper panel on the third row seat and flip it forward on the backs of the second row seats. NOTE: When returning the second row seats to their upright position, always snap the third row seat flipper panel(s) back to the third row seat first.
Page 96: Third Seat 50/50 Split Seat - If Equipped
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Seat 50/50 Split Seat — If Equipped To Fold Down The Seat(s) Folding the third row 50/50 seats requires one step. Pull up the release handle and move the seatback forward. This can be done from either in front of or behind the third row seat.
Page 97: Driver Memory System - If Equipped
To Return The Seat(s) To An Upright Position Snap the flipper panel(s) on the seat back. Then pull on the pull strap on the seat back to reposition the seat(s) to an upright position. NOTE: Make sure the seatback is properly engaged to lock the seatback to a upright position.
Page 98: Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE preset settings. Your Remote Keyless Entry transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. Your vehicle was delivered with two Remote Keyless Entry transmitters. One or both transmitters can be linked to either memory position.
Page 99: Memory Position Recall
4. Adjust the Automatic Temperature Control (ATC) while the ATC is in Auto mode. 5. Press and release the SET (S) button located on the driver’s door. 6. Within 5 seconds, press and release memory button 1 or 2 on the driver’s door. The next step must be per- formed within 10 seconds if you desire to also use a Remote Keyless Entry transmitter to recall memory po- sitions.
Page 100: To Disable A Transmitter Linked To Memory
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (S, 1, or 2), or pressing any one of the power seat buttons, or pressing the adjustable pedals button, or pressing either the LOCK or UNLOCK button on the remote keyless entry trans- mitter when not in the ignition switch.
Page 101: Driver Easy Exit And Easy Entry Control
control may be restored by first reaching the recently limited or obstructed position, then release and reactivate the same button or buttons. Continued seat travel beyond the obstructed position will indicate the recently encoun- tered self-limitation has been cleared. Driver Easy Exit and Easy Entry Control This additional feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle.
Page 102: To Open And Close The Hood
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then push the safety latch lever to the right. It is located between the grille openings left of the center.
Page 103: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 LIGHTS WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
Page 104: Interior Lights
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or when the UNLOCK button is pressed on the key fob.
Page 105: Battery Saver
all the way down to the OFF detent will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer).
Page 106: Headlight Delay
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for 90 seconds. This delay is initiated when the ignition is cycled off while the headlight switch is on, and then the headlight switch is cycled off.
Page 107: Illuminated Entry
Illuminated Entry Headlights turn on for 90 seconds, when the Remote Keyless Entry UNLOCK button is pressed. NOTE: This feature can be activated by your authorized dealer. Daytime Running Lights (Canada Only) The headlights on your Durango will illuminate when the engine is started.
Page 108: Multifunction Control Lever
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position and pressing the fog light button. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on.
Page 109: Passing Light
of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate.
Page 110: Windshield Wipers
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 111: Windshield Washers
WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 112: Traction Control Switch - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED Traction control monitors the amount of wheel spin in each of the driven wheels. If wheel spin is detected, the pressure to the brake system of the slipping wheel(s) is modulated to provide enhanced acceleration.
Page 113: Tilt Steering Column
To turn the system back ON, press the switch a second time until the traction control Indicator turns OFF. NOTE: • The traction control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF.
Page 114: Driver Adjustable Pedals - If Equipped
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 115: Adjustment
Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, up to move the pedals toward the driver or down to move the pedals away from the driver.
Page 116: Electronic Speed Control - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel.
Page 117: To Resume Speed
WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it. To Resume Speed To resume a previously set speed, push and release the RESUME button.
Page 118: To Accelerate For Passing
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Functions 3.7L Engage Speed 35 mph (56 km/h) Minimun RESUME Speed 30 mph (50 km/h) ACCEL Increase 2 mph (3km/h) COAST Decrease 1 mph (2 km/h) Dropout Speed 30 mph (50 km/h) To Accelerate For Passing Depress the accelerator as you would normally.
Page 119: Overhead Console
WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 120: Courtesy/Reading Lights
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped.
Page 121: Reset Button
RESET Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and elapsed time displays.
Page 122: Step Button
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Use this button to choose or cycle through the four trip conditions. Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases.
Page 123: Trip Odometer (Odo)
fuel capacity, which corresponds to approximately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations. NOTE: The Distance To Empty will remain equal to zero, until the vehicle runs out of fuel or is refueled.
Page 124: Compass/Temperature Display
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 free from large metal objects or power lines. The CAL symbol will turn off and the compass will function normally. Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings.
Page 126: Outside Temperature
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 127 For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
Page 128: Programming Homelink
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 129 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 130: Canadian Programming/Gate Programming
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener).
Page 131: Using Homelink
If you live in Canada or you are having difficulties programming a gate operator by using the Program- ming procedures (regardless of where you live), replace Programming HomeLink step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the cycling process to prevent possible overheating.
Page 132: Reprogramming A Single Homelink Button
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2.
Page 133: Power Sunroof - If Equipped
HomeLink is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console. Pressing the open end of the rocker switch once moves the panel to a comfort stop position short of full opening. Pressing and holding the switch causes the panel to continue moving rearward, up to the full-open position.
Page 134: Wind Buffeting
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
Page 135: Sunroof Maintenance
the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.
Page 136: Electrical Outlet Use With Engine Off
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge suffi- ciently to degrade battery life and/or prevent engine starting.
Page 137: Floor Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 FLOOR CONSOLE Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat, has the following features: • Miscellaneous storage compartments • Flexible cup holder inserts • Portable phone storage bin •...
Page 138 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The coin slots are located under the instrument panel center stack. Cup Holders The Durango has 8 cupholders. Four are located in the center console, two are located in the second row armrest, and two are located in the right hand quarter panel for third row occupants.
Page 139: If Equipped
FACTORY INSTALLED ROOF LUGGAGE RACK— IF EQUIPPED The load carried on the roof when equipped with a luggage rack must not exceed 68 kg (150 lbs.), and should be uniformly distributed over the cargo area. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 The side rails between the stantions should be used to tie down cargo.
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle.
Page 141 INSTRUMENT PANEL AND CONTROLS CONTENTS Instruments And Controls ....144 Instrument Cluster ..... . 145 Instrument Cluster Description .
Page 142 142 INSTRUMENT PANEL AND CONTROLS Operation Instructions - (CD Mode For CD Audio Play) ... 165 Load/Eject Button (CD Mode For CD Audio Play) ... 166 Notes On Playing MP3 Files .
Page 143 Climate Controls ..... . . 179 Manual Control ..... . 179 Air Conditioning Operation .
Page 144: 144 Instrument Panel And Controls
144 INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS...
Page 145: Instrument Cluster
INSTRUMENT PANEL AND CONTROLS 145 Instrument Cluster...
Page 146: Instrument Cluster Description
146 INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operat- ing satisfactorily.
Page 147 left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. 5.
Page 148 148 INSTRUMENT PANEL AND CONTROLS CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off.
Page 149 engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 11. Liftgate Open The Gate Open light will illuminate when the liftgate is not properly closed and the ignition is ON. 12.
Page 150: Traction Control
150 INSTRUMENT PANEL AND CONTROLS each position to all other positions. For a good signal the display will place a box around the selected transmission range (PRND21). If the PRNDL displays only the char- acters PRND21 (no boxes) have the system checked by an authorized dealer.
Page 151: Transmission Temperature Indicator
NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the Traction Control indicator. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
Page 152 152 INSTRUMENT PANEL AND CONTROLS light stays on, it may be an indication that the parking brake has not been released, or there is a low brake fluid level. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction.
Page 153 CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. 25.
Page 154: Radio Reception Information
154 INSTRUMENT PANEL AND CONTROLS The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button. 29. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display.
Page 155: Clock Setting Procedure
Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune / Audio control. 3. After the hours are adjusted, press the right side Tune / Audio control to set the minutes. 4.
Page 156: Operating Instructions - Radio Mode
156 INSTRUMENT PANEL AND CONTROLS Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
Page 157 NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next.
Page 158 158 INSTRUMENT PANEL AND CONTROLS Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL will display.
Page 159: Operation Instructions - Cd Mode
Preset Buttons 1 - 6 (Radio Mode) These buttons tune the Radio to the stations that you commit to push-button memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 160 160 INSTRUMENT PANEL AND CONTROLS SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Page 161: Operating Instructions - Hands Free Phone - If Equipped
Operating Instructions - Hands Free Phone — If Equipped Refer to the HANDS FREE PHONE (UConnect™) section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VIDEO CAPABILITIES INSTRUMENT PANEL AND CONTROLS 161 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 162 162 INSTRUMENT PANEL AND CONTROLS Mode Button (Radio Mode) Press the mode button repeatedly to select between the Radio, CD player, Hands Free Phone, Satellite, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode.
Page 163 RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satel- lite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency.
Page 164 164 INSTRUMENT PANEL AND CONTROLS within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broad- cast PTY information. Toggle the PTY button to select the following format types: 16 Digit-Character Dis- Program Type No program type or un- defined...
Page 165: Operation Instructions - (Cd Mode For Cd Audio Play)
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 166: Load/Eject Button (Cd Mode For Cd Audio Play)
166 INSTRUMENT PANEL AND CONTROLS begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. SEEK Button (CD MODE For CD Audio Play) Press the right side of the SEEK button for the next selection on the CD.
Page 167 LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
Page 168: Notes On Playing Mp3 Files
168 INSTRUMENT PANEL AND CONTROLS RND/PTY Button (Random Play Button) (CD MODE For CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 169 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 3-character extension) • Level 2: 31 (including a separator 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
Page 170 170 INSTRUMENT PANEL AND CONTROLS MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 171: Operation Instructions - (Cd Mode For Mp3 Audio Play)
Operation Instructions - (CD Mode For MP3 Audio Play) SEEK Button (CD Mode For MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file.
Page 172 172 INSTRUMENT PANEL AND CONTROLS Press the MSG button once more to return to elapsed time priority mode. Press and hold the MSG button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection.
Page 173: Satellite Radio - If Equipped
Operating Instructions - Video Entertainment System (VES ) (If Equipped) Refer to separate Video Entertainment System (VES ) Guide. SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast.
Page 174: Selecting Satellite Mode In Ref Radios
174 INSTRUMENT PANEL AND CONTROLS ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With RAQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds.
Page 175: Selecting A Channel
Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
Page 176: Pty Button Seek
176 INSTRUMENT PANEL AND CONTROLS one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds.
Page 177: Remote Sound System Controls - If Equipped
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. INSTRUMENT PANEL AND CONTROLS 177 The right hand control is a rocker type switch with a push button in the center.
Page 178: Cd Player
178 INSTRUMENT PANEL AND CONTROLS The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set push-buttons. CD Player Pressing the top of the switch once will go to the next track on the CD.
Page 179: Radio Operation And Cellular Phones
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from...
Page 180: Air Conditioning Operation
180 INSTRUMENT PANEL AND CONTROLS Air Conditioning Operation To turn the air conditioning On or Off perform the following steps: • Position the mode control button to the desired airflow setting. • Set the front blower control to any desired speed. •...
Page 181: Front Mode Control
Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots and give an even blend of both modes.
Page 182 182 INSTRUMENT PANEL AND CONTROLS NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Heat (Floor) Outside air flows primarily through the floor out- lets located under the instrument panel.
Page 183: Rear Temperature Control - If Equipped
Temperature Control The temperature of the air is controlled by a slide located on the top center of the control panel. Move the slide left or right to change the temperature. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 184: Rear Window Defrosting And Rear Window Washer/Wiper
184 INSTRUMENT PANEL AND CONTROLS mode on the front control will give you air from the outlets in the headliner in the rear. Floor mode in the front will give you floor in the rear. Rear Window Defrosting and Rear Window Washer/Wiper See the “Rear Window Features”...
Page 185: Level Of Automatic Control
The ATC system uses an infrared sensor located in the overhead console to measure the temperature of the driver. Based on the sensor input, the system will auto- matically control comfort by varying the temperature, fan speed, and mode. This maintains a comfortable tempera- ture, even under changing conditions.
Page 186: Manual Control (Atc)
186 INSTRUMENT PANEL AND CONTROLS Manual Control (ATC) You also may choose to customize your comfort by selecting the fan speed and mode manually. Pressing the fan speed button or any mode button places the system into manual operation. While in manual operation there are six fan speeds available and the choice of any mode.
Page 187 Manual control of Recirculation is possible only in Panel, Floor, and Bi-Level modes. It will not operate in Mix, or Defrost modes. The recirculation symbol will flash three times indicating recirculation is not available in these modes. NOTE: If the interior of the windows begin to fog, press the recirculate button to return to outside air.
Page 188 188 INSTRUMENT PANEL AND CONTROLS the A/C snowflake button has not been pressed. This dehumidifies the air to help dry the windshield. Rear Temperature Control (ATC) The “REAR FUNCTIONS” button cycles through the following modes: Rear Control from Front This allows the driver or passenger to control the rear blower speeds using the FAN +/–...
Page 189: Rear Zone Climate Control - If Equipped
Rear Zone Climate Control — If Equipped Headliner air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow. INSTRUMENT PANEL AND CONTROLS 189 The rear compartment control uses two rotary knobs: one for the temperature control and the other for the fan...
Page 190: Rear Rotary Temperature Control
190 INSTRUMENT PANEL AND CONTROLS Rear Rotary Blower Control The second row seat occupants have control of the rear blower speed, only when the front control unit is in the “REAR CONTROL” position. The rear blower switch has an “Off” position and a range of blower speeds.
Page 191: Front Unit To Rear Unit Chart
Front Unit to Rear Unit Chart If the Front Control is Rear Airflow will come selected from Panel Headliner Bi-Level Headliner • Between Bi-Level Floor Bi-Level Floor Floor Floor Defrost Floor Operating Tips Fast Cooldown For a fast cooldown, set the blower fan to the highest setting, set the mode control to the panel fresh position, press the snowflake button to turn on the air condition- ing, and drive with the windows open for the first few...
Page 192 192 INSTRUMENT PANEL AND CONTROLS and blower speed to maintain comfort. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows.
Page 193: Operating Tips Chart
INSTRUMENT PANEL AND CONTROLS 193 Operating Tips Chart...
Page 194: Rear Window Features
194 INSTRUMENT PANEL AND CONTROLS REAR WINDOW FEATURES Rear Window Wiper/Washer A rotating switch located on the climate control panel turns the rear wiper On or Off. Pressing the rotating switch inward activates the rear window washer. Rotating the switch will enable one of five intermittent delay times for the rear wiper.
Page 195: Rear Window Defrosting
If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel.
Page 197 STARTING AND OPERATING CONTENTS Starting Procedures ..... 200 Automatic Transmission ....200 Normal Starting .
Page 198 198 STARTING AND OPERATING Tire Safety Information ....221 Tire Markings ......221 Tire Identification Number (TIN) .
Page 199 Snowplow ......261 Dodge Durango Models ....261 Recreational Towing (Behind Motorhome, Etc.)
Page 200: 200 Starting And Operating
200 STARTING AND OPERATING STARTING PROCEDURES The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position.
Page 201: Normal Starting
Normal Starting Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
Page 202: Engine Block Heater - If Equipped
202 STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. After Starting The idle speed is automatically controlled on fuel injected engines and will decrease as the engine warms up.
Page 203: Automatic Transmission
WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION Automatic Transmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. To drive, move the selector lever from Park or Neutral to the desired drive position.
Page 204 204 STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park).
Page 205 “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive For most city and highway driving. “2”...
Page 206 206 STARTING AND OPERATING • transmission has reached normal operating tempera- ture. NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level.
Page 207 performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
Page 208: Four-Wheel Drive Operation
208 STARTING AND OPERATING transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position.
Page 209 or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required. WARNING! Always engage the parking brake when powering down the vehicle if the Service 4WD light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury.
Page 210: Shifting Procedure - Nv 144 Transfer Case
210 STARTING AND OPERATING 4LOCK Four-Wheel-Drive LOCK - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Shifting Procedure - NV 144 Transfer Case AWD to 4LOCK or 4LOCK to AWD With the key ON and the engine either OFF or RUN- NING, rotate the transfer case switch, located on the...
Page 211: Nv 244 Generation Ii Transfer Case Operating Information / Precautions
NOTE: Delayed shifting out of 4LOCK may be experi- enced due to uneven tire wear, low tire pressure, or excessive vehicle loading. NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light will flash and the current transfer case position will be maintained.To retry a selection, turn the control knob back to the current...
Page 212 212 STARTING AND OPERATING vehicle in the 4LOCK position on dry hard surfaced roads. This feature provides the safety, security, and convenience of operating in all-wheel drive at all times regardless of road conditions. When additional traction is required, the 4LOCK and 4LO positions can be used to lock the front and rear driveshafts together through the transfer case inter-axle differential and force the front and rear wheels to rotate...
Page 213 WARNING! Always engage the parking brake when powering down the vehicle if the Service 4WD light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
Page 214 214 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 215: Shifting Procedure - Nv 244 Generation Ii
Shifting Procedure - NV 244 Generation II Transfer Case NOTE: The 4x4 system will not allow shifts between AWD/ 4LOCK if the rear wheels are spinning (no traction). In this situation a position indicator light will flash and the original position indicator light will remain ON.
Page 216 216 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to complete stop. 2.
Page 217: Parking Brake
PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. STARTING AND OPERATING 217 Be sure the parking brake is firmly set when parked and the gear-shift lever is in PARK position.
Page 218: Brake System
218 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury.
Page 219 The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The Anti-Lock Brake system includes an amber (ABS) warning light. When the light is illuminated, the Anti- Lock Brake system is not functioning.
Page 220: Power Steering
220 STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 221: Rocking The Vehicle
ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. The least amount of accelerator pedal pressure to main- tain the rocking motion without spinning the wheels or racing the engine is most effective.
Page 222 222 STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 223 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 224 224 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 225: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 226: Tire Loading And Tire Pressure
226 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. Tire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle...
Page 227 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 228 228 STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 229 STARTING AND OPERATING 229...
Page 230: Tires-General Information
230 STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 231: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 232 232 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 233 Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 234: Radial-Ply Tires
234 STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 235: Limited Use Spare - If Equipped
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 236: Tire Spinning
236 STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly.
Page 237: Replacement Tires
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 238: Alignment And Balance
238 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 239: Supplemental Tire Pressure Information
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 240: Snow Tires
240 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Durango trucks. NOTE: The use of class “S” chains is permitted on Durangos with P245/70R17 tires.
Page 241: Tire Rotation Recommendations
TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns. These effects can be reduced by timely rotation of tires.
Page 242: Fuel Requirements
242 STARTING AND OPERATING FUEL REQUIREMENTS All engines (except 5.7L engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality un- leaded “regular” gasoline having an oc- All Engines tane rating of 87. The routine use of pre- Except 5.7L mium gasoline is not recommended.
Page 243: Reformulated Gasoline
and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality.
Page 244: Mmt In Gasoline
244 STARTING AND OPERATING MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance.
Page 245: Materials Added To Fuel
CAUTION! If the Check Engine or Service Engine Soon light is flashing, immediate service is required; see onboard diagnostics system section. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
Page 246 246 STARTING AND OPERATING WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door.
Page 247: Fuel System Cautions
WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive.
Page 248: Carbon Monoxide Warnings
248 STARTING AND OPERATING • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock. If spark knock persists, lighten the load, or engine piston damage may result.
Page 249: Catalytic Converter
the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle. CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only.
Page 250: Vehicle Loading
250 STARTING AND OPERATING vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained imme- diately. To minimize the possibility of catalyst damage: • Do not try to start the engine by pushing or towing the vehicle.
Page 251 Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN).
Page 252: Curb Weight
252 STARTING AND OPERATING Inflation Pressure (Cold) This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
Page 253 WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle.
Page 254: Trailer Towing
254 STARTING AND OPERATING TRAILER TOWING To maintain warranty coverage, follow the requirements and recommendations in this manual concerning ve- hicles used for trailer towing. Definitions The following trailer towing related terminology defini- tions will assist in understanding the subsequent sec- tions: GROSS COMBINATION WEIGHT RATING (GCWR) is the total permissible weight of your vehicle and trailer...
Page 255 Consider the following items when computing the weight on the rear axle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
Page 256: Trailer And Tongue Weight
256 STARTING AND OPERATING • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs. (907 kg). • Use an approved trailer harness and connector. If a hitch is ordered, the proper wiring will be provided. •...
Page 257: Gross Combined Vehicle Weight Rating (Gcwr)
Trailer sway control and equalizing hitch are required for tongue weights above 350 lbs. (159 kg). Also, there are maximum tongue weight ratings that are not to be exceeded, as follows: • Class IV (the receiver hitch type) 1200 lbs (544 kg) STARTING AND OPERATING 257 Gross Combined Vehicle Weight Rating (GCWR) The Gross Combined Vehicle Weight Rating (GCWR) is...
Page 258: Trailer Towing Information (Maximum Trailer Weight Ratings)
In Canada, refer to the following website address: http:// www.dodge.ca. Trailer Towing Requirements All Dodge Durango trucks are intended to tow trailers up to 2,000 lbs. (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers over 2,000 lbs.
Page 259: Trailer Tow Wiring
outside lamp/bulb failure. Therefore, an occasional vi- sual check around the vehicle is recommended. Once the trailer is removed the above indication will return to the vehicle. WARNING! The direct connection of hydraulic brake lines from vehicle brake system to trailer system is not accept- able.
Page 260: Cooling System Tips-Trailer Towing
260 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7 - Pin Connector Cooling System Tips—Trailer Towing To reduce potential for engine and transmission over- heating, take the following actions: •...
Page 261: Snowplow
STARTING AND OPERATING 261 SNOWPLOW Dodge Durango Models NOTE: Do not use Dodge Durango Models for snow- plow applications. WARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end or your vehicle.
Page 262: Recreational Towing (Behind Motorhome, Etc.) Of 4X4 Vehicles
262 STARTING AND OPERATING CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) OF 4X4 VEHICLES...
Page 263: Shifting Into Neutral (N)
CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: The NV 244 Generation II transfer case must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection button is located on the lower left hand corner of the 4WD Control Switch.
Page 264 264 STARTING AND OPERATING 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement.
Page 265: Shifting Out Of Neutral (N)
CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P) Shifting OUT of Neutral (N) Use the following procedure to prepare your vehicle for normal usage.
Page 266 266 STARTING AND OPERATING the 1 second time, then all of the position indicator lights will flash continuously until all requirements are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
Page 267: Traction
TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 269 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....270 Adding Fuel ......270 Changing A Flat Tire .
Page 270: Hazard Warning Flasher
270 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers.
Page 271 WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed. You could be burned. Always place gas contain- ers on the ground while filling. WHAT TO DO IN EMERGENCIES 271 WARNING! Remove the gas cap slowly to prevent fuel spray from the filler neck which may cause injury.
Page 272: Changing A Flat Tire
272 WHAT TO DO IN EMERGENCIES CHANGING A FLAT TIRE Jack Location In the Durango, the scissor jack and tire changing tools are stowed under the second row seat. The jack is secured in place with a winged stud and a fixed stud.
Page 273: Removing The Spare Tire
Avoid ice or slippery areas. WHAT TO DO IN EMERGENCIES 273 Removing The Spare Tire The spare tire on the Dodge Durango is located under- neath the vehicle in the rear.
Page 274 274 WHAT TO DO IN EMERGENCIES Remove the spare tire before attempting to jack the truck. 1. Remove the rubber plug from the floor in the cargo area. 2. Engage the jack wrench extension to the spare tire winch through the hole in the floor. 3.
Page 275: What To Do In Emergencies 275
Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 276 276 WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
Page 277 When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as posssible with the drive tubes extending to the rear.
Page 278 278 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6.
Page 279: To Stow The Flat Or Spare
WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised.
Page 280: Jump Starting
280 WHAT TO DO IN EMERGENCIES JUMP STARTING WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or cloth- ing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the con- taminated area immediately with large quantities of water.
Page 281 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result.
Page 282: Towing A Disabled Vehicle
282 WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
Page 283 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment 3.7L V6 ....286 Engine Compartment 4.7L V-8 ....287 Engine Compartment 5.7L HEMI V-8 .
Page 284 284 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 302 Power Steering — Fluid Check ... . 303 Front Suspension Ball Joints ....304 Drive Shaft Constant Velocity Joints .
Page 285 Fog Lights ......335 Fluids And Capacities ....335 Recommended Fluids, Lubricants And Genuine Parts .
Page 286: 286 Maintaining Your Vehicle
286 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.7L V6...
Page 287: Engine Compartment 4.7L V-8
MAINTAINING YOUR VEHICLE 287 ENGINE COMPARTMENT 4.7L V-8...
Page 288: Engine Compartment 5.7L Hemi V-8
288 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 5.7L HEMI V-8...
Page 289: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 290: Emissions Inspection And Maintenance Programs
290 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...
Page 291: Replacement Parts
the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
Page 292: Maintenance Procedures
292 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
Page 293 1. Position the vehicle on a level surface. 2. Turn Off the engine and allow approximately 5 min- utes for the oil to settle to the bottom of the crankcase. 3. Remove the engine oil level indicator (dipstick). 4. Wipe the engine oil level indicator (dipstick) clean. 5.
Page 294: Maintenance Schedules
294 MAINTAINING YOUR VEHICLE Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures are below 32°F (0°C). •...
Page 295 The proper SAE viscosity grade of engine oil should be selected based on the following recommendation and be within the operating temperature shown in the recom- mended SAE viscosity chart. • SAE 5W-30 is the preferred oil for Dodge Trucks with 3.7L/4.7L/5.7L engines. Synthetic engine oils may be...
Page 296 296 MAINTAINING YOUR VEHICLE used provided that the oil quality requirements de- scribed above are met and the recommended mainte- nance intervals for oil and filter changes are followed. • Lubricants which do not have both the engine oil certification mark or current service symbol and the correct viscosity grade number should not be used.
Page 297: Engine Oil Filter
governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter.
Page 298: Ignition Cables
298 MAINTAINING YOUR VEHICLE due to a faulty spark plug. Check the Vehicle Emissions Control Information label for the proper type of spark plug for your vehicle. CAUTION! When replacing plugs, do not overtighten. You could damage them and cause them to leak. Ignition Cables Replace the ignition cables (5.7L engines only) at the mileage interval shown in the maintenance charts.
Page 299: Engine Fuel Filter
Engine Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. Catalytic Converter The catalytic converter requires the use of unleaded fuel only.
Page 300: Maintenance-Free Battery
Maintenance-Free Battery All Dodge trucks are equipped with maintenance-free batteries. You will never have to add water, nor is periodic maintenance required.
Page 301 WARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. MAINTAINING YOUR VEHICLE 301 To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration.
Page 302: Air Conditioner Maintenance
302 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test.
Page 303: Power Steering - Fluid Check
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 304: Front Suspension Ball Joints
304 MAINTAINING YOUR VEHICLE Front Suspension Ball Joints The ball joints and seals should be inspected whenever the vehicle is serviced for other reasons. Damaged seals should be replaced to prevent leakage or contamination of the grease. Drive Shaft Constant Velocity Joints All four wheel drive models are equipped with four constant velocity joints.
Page 305: Windshield Wiper Blades
Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accu- mulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
Page 306: Exhaust System
306 MAINTAINING YOUR VEHICLE freezing the fluid on the cold windshield. Mopar All Weather Windshield Washer Solution used with water as directed on the container, aids cleaning action, reduces freezing point to avoid line clogging, and is not harmful to paint or trim. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust...
Page 307 bugs, leaves, etc. If dirty, clean the radiator core by gently spraying water from a garden hose at the back of the core. Check the coolant bottle tubing for condition and tight- ness of connection at coolant bottle and radiator. Inspect the entire system for leaks.
Page 308 308 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill If the solution is dirty and contains a considerable amount of sediment, it should be cleaned and flushed. See your authorized dealer for proper draining, flushing and refilling of your vehicle’s cooling system. Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal.
Page 309 CAUTION! Mixing of coolants other than specified (non- HOAT), may result in engine damage that may not be covered under the new vehicle warranty, and decreased corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 310 310 MAINTAINING YOUR VEHICLE WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool overheated engine. The coolant is under pres- sure and severe scalding could result. Coolant Pressure Cap The coolant pressure cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant coolant bottle.
Page 311: Emission Related Components
The radiator normally remains completely full, so there is no need to remove the pressure cap except checking coolant freeze point or replacement with new antifreeze coolant. Your service attendant should be advised of this. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle.
Page 312 312 MAINTAINING YOUR VEHICLE swelling suggest deterioration of the rubber. Particular attention should be given to examining hose surfaces nearest to high heat sources, such as the exhaust mani- fold. Insure nylon tubing in these areas has not melted or collapsed.
Page 313: Brake System
Brake System Power Disc Brakes (Front) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. MAINTAINING YOUR VEHICLE 313 Brake Master Cylinders The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on.
Page 314 314 MAINTAINING YOUR VEHICLE WARNING! Use of brake fluid that may have a lower initial boiling point, or is unidentified, as to specifications may result in sudden brake failure during hard prolonged braking. You could have an accident. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching on fire.
Page 315: Automatic Transmission
WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Automatic Transmission Fluid Level Check – 3.7L Engine This fluid level should be checked when the engine is fully warmed up and the fluid in the transmission is heated to its normal operating temperature.
Page 316 316 MAINTAINING YOUR VEHICLE 5. Remove the dipstick and feel if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips.
Page 317 4. Place the gear selector momentarily in each gear position ending with the lever in P (Park). 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides.
Page 318 Authorized Dodge Dealer or Service Center. It is important that the transmission be adjusted periodically, the fluid main- tained at the correct level, and that it be drained and refilled as specified.
Page 319: Transfer Case
Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low. Have the transfer case serviced immediately. CAUTION! Damage may result from operation of the vehicle with low transfer case fluid. The transfer case fluid should be drained and refilled at the intervals specified.
Page 320: Selection Of Lubricating Grease
320 MAINTAINING YOUR VEHICLE Front Axle Front Axle fluid level should be at the bottom of the filler hole plug. Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for chassis components.
Page 321: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 322 322 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
Page 323 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. •...
Page 324 324 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer.
Page 325: Power Distribution Center (Fuse/Relay)
POWER DISTRIBUTION CENTER (FUSE/RELAY) Your vehicle is equipped with two electrical power distribution centers located next to each other in the left side of the engine compartment. Thess power distribution centers house new plug-in “Maxi” fuses which replace all the in-line fusible links previously used.
Page 326: Vehicle Storage
326 MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it suggests a problem in the circuit that must be corrected.
Page 327: Replacement Light Bulbs
REPLACEMENT LIGHT BULBS Dome Light ......WL212–2 Liftgate Lamp ......567 Overhead Console Lights .
Page 328 328 MAINTAINING YOUR VEHICLE 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by removing the fender panel access door which is located in the wheel liner. 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel.
Page 329: Rear Side Marker, Tail Lights, Turn Signals And Backup Lights - Replacement
MAINTAINING YOUR VEHICLE 329 Rear Side Marker, Tail Lights, Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing.
Page 330 330 MAINTAINING YOUR VEHICLE 2. Rotate the light to the outboard side of the vehicle and 3. Unlock and remove electrical connector. remove.
Page 331 MAINTAINING YOUR VEHICLE 331 4. Remove the three screws holding the bulb strip to the 5. Remove the bulb strip from the tail light lens. back of the tail light lens.
Page 332 332 MAINTAINING YOUR VEHICLE 6. Remove bulbs from bulb strip by pulling the bulb straight out.
Page 333: License Lights
License Lights 1. Remove the two screws securing the lens to the liftgate. MAINTAINING YOUR VEHICLE 333 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket.
Page 334: Center High-Mounted Stoplight
334 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assem- bly to the liftgate. 3. Pull bulb straight from socket to remove. 2. Turn socket 1/4 counterclockwise and free from hous- ing.
Page 335: Maintaining Your Vehicle
Fog Lights 1. Rotate bulb and connector 1/4 turn counterclockwise. 2. Pull bulb off of connector. FLUIDS AND CAPACITIES Fuel 3.7L/4.7L, 87 Octane 5.7L, 89 Octane Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified 5.7L, SAE 5W-30, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle...
Page 336 336 MAINTAINING YOUR VEHICLE 3.7L with Rear Heat (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L without Rear Heat (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L with Rear Heat (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L without Rear Heat (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L with Rear Heat (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula)
Page 337: Engine
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) P/N 5011764AB or equivalent. Engine Oil Use SAE 5W-30, API Certified, meeting material standard MS-6395. Engine Oil Filter Mopar Engine Oil Filter, P/N 5281090 or equivalent.
Page 338: Chassis
338 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant. SAE 75W-140 Synthetic Gear Lubricant.
Page 339 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..340 Emissions Testing ..... . . 340 Maintenance Schedules .
Page 340: Emission Control System Maintenance
340 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 341: Maintenance Schedules
MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. •...
Page 342 342 MAINTENANCE SCHEDULES CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 343: Schedule "B" 343
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 344 344 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if neces- sary. 3,000 6,000 9,000 (5 000) (10 000) (14 000) 12,000 15,000 (19 000)
Page 345 Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only).
Page 346 346 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. 33,000 36,000 39, 000 (53 000) (58 000) (62 000) 42,000...
Page 347 Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect and replace ignition cables if necessary (5.7L only).
Page 348 348 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Inspect auto tension drive belt and replace if re- quired.
Page 349 Miles (Kilometers ) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if re- quired.
Page 350 350 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Flush and replace engine coolant. Change rear axle fluid. Change front axle fluid (4X4). 93,000 96,000 99,000 (149 000) (154 000) (158 000) 100,000 102,000 (160 000) (163 000)
Page 351 Miles (Kilometers) Change engine oil and engine oil filter. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect and replace ignition cables if neces- sary (5.7L only).
Page 352 352 SCHEDULE “B” Miles (Kilometers) Drain and refill automatic transmission fluid, change filter (3.7L). This applies only if your vehicle is used for police, taxi, fleet, or trailer towing. Drain and refill automatic transmission fluid and change main sump filter (4.7L/5.7L only). * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty.
Page 353: Schedule "A" 353
Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. 6,000 12,000 18,000 (10 000) (19 000) (29 000) [12] [18] SCHEDULE “A”...
Page 354 354 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60 months, regardless of mileage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs.
Page 355 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required.‡...
Page 356 356 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Drain and refill tranfer case fluid (4X4). Flush and replace engine coolant, if not done at 60 mos. Flush and replace engine coolant, if not done at 102,000 miles (163 000 km) Inspect brake linings.
Page 357 Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. SCHEDULE “A” 357 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 359: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......360 Prepare For The Appointment .
Page 360: Suggestions For Obtaining Service For Your Vehicle
360 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 361 The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf.
Page 362 362 IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni-...
Page 363: Warranty Information
Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
Page 364 364 IF YOU NEED CONSUMER ASSISTANCE...
Page 365: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 366: Publication Order Forms
366 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 367 • Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips. IF YOU NEED CONSUMER ASSISTANCE 367 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada)
Page 369 INDEX...
Page 370 370 INDEX Adding Engine Coolant (Antifreeze) ..309 Adding Fuel ......245,270 Air Cleaner, Engine .
Page 371 Axle Lubrication ......319 Ball Joints ......304 Battery .
Page 372 372 INDEX Center High Mounted Stop Light ... . 334 Certification Label ..... . . 250 Changing A Flat Tire .
Page 373 Daytime Running Lights ....107 Dealer Service ......291 Defroster, Rear Window .
Page 374 374 INDEX Exhaust Gas Caution ....62,248 Fails to Start ......201 Flooded, Starting .
Page 375 Transfer Case ......319 Fog Lights ......107,335 Folding Rear Seat .
Page 376 376 INDEX Headlights ......327 Delay ......106 High Beam .
Page 377 Key, Replacement ......10 Key, Sentry ......9 Key-In Reminder .
Page 378 378 INDEX Turn Signal ......108,329 Warning (Instrument Cluster Description) ..146 Washer Fluid ......153 Loading Vehicle .
Page 379 Rearview ......70 Vanity ....... 73 Modifications/Alterations, Vehicle .
Page 380 380 INDEX Pets ........61 Pets, Transporting ......61 Phone, Cellular .
Page 381 Reclining Front Seats ..... . 87 Recommended Fluids, Lubricants and Genuine Parts ....... 337 Recreational Towing .
Page 382 382 INDEX Pretensioners ......35 Reminder ......147 Seats .
Page 383 Emergency (Jump Starting) ....280 Engine Block Heater ....202 Engine Fails to Start .
Page 384 384 INDEX Jacking ......275 Load Capacity ..... 226,227 Radial .
Page 385 Filter ....... 318 Fluid ......318,338 Maintenance .
Page 386 386 INDEX Windshield Defroster ....63,182,187 Windshield Washers ....110,111,305 Fluid .

This manual is also suitable for:

2004 hb durango

Dodge 2004 Durango Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Instrument Panel and Controls

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Dodge 2004 Durango

Summary of Contents for Dodge 2004 Durango