Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
This number also appears on the Automobile Information NOTE: It is illegal to remove the VIN plate. Disclosure Label affixed to a window on your vehicle.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Key-In-Ignition Reminder .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicle Theft Alarm — If Equipped ...26 Sliding Side Door ......28 Power Sliding Door —...
Page 11 Rear Seat Delete Feature (Commercial Vehicles Only) — If Equipped ..66 Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only) .......67 Engine Break-In Recommendations .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer.
Page 13: Key-In-Ignition Reminder
The power window switches, radio, power NOTE: outlets, and removable console (if equipped), will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Page 14 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated.
Page 15: Replacement Keys
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 16: General Information
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 17: Door Locks
NOTE: • The front courtesy overhead console, door courtesy and liftgate lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the “defeat”...
Page 18: Power Door Locks - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 19 If you press the power door lock switch while the sliding door is open, the sliding door will lock. Automatic Door Locks — If Equipped The doors will lock automatically on vehicles with power door locks if: 1. The transmission is in gear, 2.
Page 20: Remote Keyless Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. any door is opened (excluding liftgate) and 5. the vehicle speed is 0 mph (0 km/h). The Auto Unlock feature can be enabled or disabled by performing the procedure in the Overhead Console, Customer Programmable Features section.
Page 21 Three Button Transmitter Six button transmitters will provide functions that allow the same basic operation as the three button, but may also be used to Open/Close the optional power liftgate, left power sliding door, or right power sliding door. Other options of the system allow you to turn ON/OFF the THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Sound Horn On Lock, Remote Unlock Driver’s Door 1st,...
Page 22: To Unlock The Doors And Liftgate
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door side of the vehicle, or twice to unlock all doors and liftgate. The illuminated entry system also turns on.
Page 23: To Program Transmitters
headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on. The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or by turning the ignition switch to the ON position.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Open/Close Right Power Sliding Door — If Equipped Press the RIGHT button twice within five seconds to open/close the right power sliding door. If the button is pushed while the door is being power closed, the door will reverse to the full open position.
Page 25: General Information
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 26: Vehicle Theft Alarm - If Equipped
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case snap two halves together.
Page 27 and moving the ignition switch to the ON/START posi- tion will disarm the system. If you disarm the system and access the liftgate area, the system must be rearmed, as described previously, when closing the liftgate. If some- thing has triggered the system in your absence, the horn will sound three times when you disarm the system.
Page 28: Sliding Side Door
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE exterior lights will flash, the horn will sound, and the ignition will not start the vehicle. If this occurs, disarm the system. SLIDING SIDE DOOR The sliding door may be opened from the inside or the outside.
Page 29: Power Sliding Door - If Equipped
• Avoid high impacts against the door stop when open- ing the door. This is very important when your vehicle is parked on an incline as the door will slide faster in the downhill direction. • There is a hold-open latch that is activated when the sliding door is fully opened.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power sliding door may also be opened by pressing the switches on the overhead console or the switch located on the trim panel just in front of the sliding door. To keep your door operating properly, observe the fol- lowing guidelines.
Page 31 If the inside or outside door handles are used while the power sliding door is activated, the power sliding door feature will be canceled and the door must be opened or closed manually. To avoid unintentional operation of the power sliding door from the rear seats, press the button located in the overhead console to disable the switches for the rear seat passengers.
Page 32: Child Protection Door Lock
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. WARNING! To avoid trapping anyone in the vehicle in a colli- sion.
Page 33: Liftgate
door, regardless of the child lock lever position. To avoid unintentional operation of the power sliding door from the rear seats, press the button located in the overhead console to disable the switches for the rear seat passengers. NOTE: • The power sliding door switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
Page 34: Power Liftgate - If Equipped
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the liftgate is locked and is not equipped with a powered liftgate, pressing the button on the remote keyless entry transmitter will result in the liftgate becom- ing unlocked for 30 seconds allowing you to manually access the liftgate area.
Page 35 WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance.
Page 36: Windows
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle.
Page 37: Power Windows - If Equipped
Power Windows — If Equipped You can control either front window using switches on the driver’s door trim panel. There is a single switch on the passenger’s door trim panel which operates the passenger door window. The switches will operate only when the ignition switch is in the ON or ACCESSORY position.
Page 38: Occupant Restraints
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power window switches remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
Page 39: Lap/Shoulder Belts
WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 43 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 45: Lap/Shoulder Belt Untwisting Procedure
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3.
Page 47: Center Lap Belts
Center Lap Belts The center seating positions have a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a “click”. To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing.
Page 48: Seat Belts And Pregnant Women
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 49 NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment in low speed collisions. The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seatbacks,...
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may dam- age the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 51 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 53 How The Front Airbag System Works • The front airbag control module determines if a frontal impact is severe enough to require the front airbags to inflate. Based on the level of collision severity, the front airbag control module determines the proper rate of inflation.
Page 54: Side Airbags Supplemental Restraint System (Srs) - If Equipped
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the front airbag control module detects a colli- sion requiring the front airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different front airbag inflation rates are possible, these rates are determined by the front airbag control module based on collision severity.
Page 55 The front airbag control module also monitors the readi- ness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, instrument panel and the steering wheel and column.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation.
Page 57 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 58: Daimlerchrysler Corporation Integrated Child Seat - If Equipped
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DaimlerChrysler Corporation Integrated Child Seat — If Equipped Operating instructions for this seat are included with the seat. If the instructions are not with the seat or in the Owner’s Manual Package, replacement instructions can be obtained.
Page 59 Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child restraint anchorage system. Refer to “Lower Anchors and Tether for CHildren (LATCH)” later in this section. • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
Page 61 Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle.
Page 63 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Child restraint systems having attachments designed to connect to the lower anchorages are now available.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. Installing the Child Restraint System If your fleet vehicle is equipped with LATCH anchorages on the 3-passenger bench seat, do not install three child...
Page 65 In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
Page 66: Rear Seat Delete Feature (Commercial Vehicles Only) - If Equipped
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.
Page 67: Restraining Infants And Small Children With Seat Delete Feature
Restraining Infants and Small Children with Seat Delete Feature (Commercial Vehicles Only) There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: •...
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Locate the child restraint tether anchor on the floor just behind the front passenger seat. 2. Extend the child restraint tether anchor forward to- wards the front passenger seat. 3. Follow the child restraint manufacturer’s directions for proper use of connecting the child restraint to the extended tether strap.
Page 69 5. Route the tether strap beneath the head restraint between the two head restraint posts. Ensure that the child restraint tether strap is centered between the two head restraint posts. 6. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal ring on the vehicle tether anchor.
Page 70: Engine Break-In Recommendations
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The vehicle tether anchor is designed to be used with a child restraint only. It should not be used for any other purpose. Before use inspect the tether anchor strap for nicks, abrasions, discoloration, and loose threads.
Page 71: Safety Tips
SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 72: Periodic Safety Checks You Should Make Outside The Vehicle
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked.
Page 73: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......77 Inside Day/Night Mirror ....77 Automatic Dimming Mirror —...
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Reclining Seats — If Equipped ..83 Manual Lumbar — If Equipped ... .84 Middle Rear Bench Seat Recline — If Equipped .
Page 75 Turn Signals ......102 Headlight Low/High Beam Selector Switch . . . 103 Passing Light ......103 Windshield Wipers And Washers .
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Erasing Homelink Buttons ....124 Reprogramming a Single Homelink Button . . . 124 Security ......124 Power Sunroof —...
Page 77: Mirrors
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 (toward rear of vehicle).
Page 78: Driver's Side Outside Mirror Auto Dimmer - If Equipped
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you.
Page 79: Power Remote-Control Mirrors - If Equipped
WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror.
Page 80: Heated Remote Control Mirrors - If Equipped
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Rear Window Defrost. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor.
Page 81: 8-Way Driver's Power Seat - If Equipped
WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Your vehicle may be equipped with side airbags.
Page 82: Adjustable Head Restraints - If Equipped
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 83: Manual Reclining Seats - If Equipped
Manual Reclining Seats — If Equipped The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 seatback to its normal position.
Page 84: Manual Lumbar - If Equipped
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 85: Middle Quad Fold & Tumble Seating
Middle Quad Fold & Tumble Seating The passenger’s and driver’s side middle quad seats can be tilted forward for easy access to the third seat or rear cargo area. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 To tilt the seat, pull up on the release handle and tilt the seat fully forward.
Page 86: Middle Quad Fold & Tumble Seat Removal
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In the event of a collision you could be injured if the seat is not fully latched. Middle Quad Fold & Tumble Seat Removal 1. Remove any obstructions from the floor in front of the seat.
Page 87 5. Pull the release bar located at the bottom front edge of the seat to disengage the front attachments. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 6. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers. To reinstall the seat, remove any obstructions from the floor in front of the seat and ensure the head restraint is in its full downward position.
Page 88: 50/50 Fold & Tumble Rear Seat Removal
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to engage the rear attachments. Pull the seatback release lever to return the seatback to its full upright position. Ensure that the seatback is fully latched in the upright position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments.
Page 89 3. Pull the release strap “3” located at the bottom of the seat to disengage the front attachments. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 4. The seat assembly can now be removed from the vehicle and moved on its Easy Out Rollers. To reinstall the 50/50 rear seat, lower the head restraint to the full down position, tilt the seat forward and engage the front floor attachments, then tilt the seat rearward to...
Page 90: Passenger And 3 - Passenger Bench Seats
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE lever to return the seatback to its full upright position. Ensure that the seatback is fully latched in the upright position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments.
Page 91: Plastic Grocery Bag Retainer
WARNING! If not properly latched, the bench seats could be- come loose. Personal injuries could result. After reinstalling these seats, be sure the red indicator button on the release handles return into the handles. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats.
Page 92: Rear-Most Bench Seat
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear-Most Bench Seat The seat position can be adjusted fore and aft to any of three positions - normal (rearward), intermediate, and full forward. In this way varying needs for legroom and cargo space behind the seat can be accommodated. The release lever is below the seat and is accessible from the front and back of the seat.
Page 93 1. Normal Seating— The 2nd and 3rd row seats are installed. The 3rd row bench seat is in the full rear position on the tracks. 2. Increased Storage— Increased storage area is provided by adjusting 3rd row bench seat to the intermediate track position. Rear seat- ing for 3 passengers (children) is still provided.
Page 94: Rear Quad And 50/50 Seating Flexibility
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Auxiliary Seating— The middle quad seats are removed from the vehicle. The 3– passenger bench seat can be installed in either the second or third row. Rear Quad and 50/50 Seating Flexibility The seats may be used with either or both seatbacks folded forward for additional storage space, or with either or both seats removed from the vehicle.
Page 95 NOTE: Driving with the 2nd-row seats in the tumbled position is not recommended when passengers occupy the 3rd row seats. This position is intended only to increase available cargo area without requiring removal of the seats. Do not leave the head restraint stored between the cushions for extended periods of time or inadvertent damage to the seat cover or head restraint may occur.
Page 96: To Open And Close The Hood
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat.
Page 97 Next, push to the left the safety catch located under the front edge of the hood, near the center. Use the hood prop rod to secure the hood in the open position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 To prevent possible damage, do not slam the hood to close it.
Page 98: Lights
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS All of the lights, except the hazard warning lights, are controlled by switches to the left of the steering column on the instrument panel. Interior Lights Interior lights are turned on when a door or liftgate is opened, the keyless entry transmitter is activated, or when the dimmer control is moved to the extreme top.
Page 99: Park Lights
NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate. Park Lights Turn this switch to the first detent to turn the park lights on. This also turns on all instrument panel lighting.
Page 100: Automatic Headlights - If Equipped
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior light Defeat (OFF) Rotate the dimmer control to the OFF position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent.
Page 101: Daytime Running Lights (Canada/Fleet Vehicles Only)
Daytime Running Lights (Canada/Fleet Vehicles Only) The Daytime Running Lights will come on whenever the vehicle is running, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or the park lights are left on, or if the dimmer control is in the extreme top position after the ignition switch is turned off, a chime will sound when the...
Page 102: Front Fog Lights - If Equipped
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The lights must be turned off within 45 seconds of turning the ignition off to activate this feature Front Fog Lights — If Equipped To activate the front fog lights, turn on the park lights or the low beam headlights and pull out on the headlight switch control knob.
Page 103: Headlight Low/High Beam Selector Switch
Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about one mile with the turn signals on, a chime will sound to alert the driver. Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel to switch the headlights between HIGH and LOW beam.
Page 104: Tilt Steering Column - If Equipped
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE a maximum of 20 seconds or until the lever is released. If another washer cycle is desired the end of the lever must be pressed again to get another 20 second washer cycle. If the lever is depressed while in the delay range, the wipers will operate for several seconds after the lever is released, and then resume the intermittent interval pre-...
Page 105: Traction Control Switch - If Equipped
WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 TRACTION CONTROL SWITCH —...
Page 106: Adjustable Pedals - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system back ON, press the switch a second time until the TRAC OFF indicator turns OFF. NOTE: • The Traction Control System indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF.
Page 107: Electronic Speed Control - If Equipped
• The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control System is ON. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information Sys- tem (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled —...
Page 108: To Activate
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located below the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off.
Page 109: To Vary The Speed Setting
To Vary the Speed Setting: When the speed control is set, speed can be increased by pressing and holding the “RESUME/ACCEL” button. When the button is released, a new set speed will be established. Tapping the “RESUME/ACCEL” button once will result in a 2 mph (3 km/h) speed increase.
Page 110: Overhead Console - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 111: Sunglass Storage
The lights also turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed. The area around the instrument panel cupholders is also illuminated from a light in the overhead console.
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turns in an area free from large metal or metallic objects, the “CAL” symbol will turn off and the compass will function normally. Manual Compass Calibration If the compass appears erratic and the “CAL” symbol does not appear, you must put the compass into the Calibration Mode manually.
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 To set the variance: Turn the ignition switch ON and set the display to Comp/Temp. On vehicles equipped with a Compass/Mini Trip Computer press the RESET button for approximately 5 seconds. On vehicles equipped with Compass/Temp press and hold the C/T and US/M buttons for 5 seconds.
Page 114: Mini-Trip Computer
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mini-Trip Computer This displays information on the following: • Average Fuel Economy (ECO AVG) Shows the average fuel economy since the last reset. • Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank.
Page 115: Electronic Vehicle Information Center (Evic) - If Equipped
Electronic Vehicle Information Center (EVIC) — If Equipped The Electronic Vehicle Information Center, when the appropriate conditions exist, displays the following WARNING messages and symbols. Each message is accompanied by a single chime: • TURN SIGNALS ON (with graphic) • PERFORM SERVICE •...
Page 116: Customer Programmable Features - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Tire pressure menu items are available only on vehicles equipped with the Tire Pressure Monitor Sys- tem. Customer Programmable Features — If Equipped Press the “MENU” button until one of the display choices following appears: Language When in this display you may select one of five lan-...
Page 117 the Tire Pressure Monitor system and the training routine is not performed, training will be cancelled after one minute or the next time you cycle the ignition key. See your authorized dealer for service and retraining of the system. Use Factory Settings If “Yes”...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Remote Linked To Memory (Available with Memory Seat and Pedals Only) When this feature is selected, pressing the Unlock button on any Remote Keyless Entry transmitter already linked to memory will return the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station presets to their memory set positions.
Page 119: Garage Door Opener - If Equipped
30, 60, or 90 seconds, or not remain on. Pressing the “STEP” button when in this display will select 30, 60, 90, or “OFF.” Headlamp On With Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch has been moved to the “AUTO”...
Page 120: Programming Homelink
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 121 WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the Gate Operator/Canadian Pro- gramming section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter.
Page 123: Canadian Programming/Gate Programming
and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device. NOTE: To program the remaining two HomeLink but- tons, begin with Programming step two.
Page 124: Erasing Homelink Buttons
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-355- 3515.
Page 125: Power Sunroof - If Equipped
This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.
Page 126: Express Open Feature
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the button located to the right of the sunroof switch, to open the vent. The sunroof can be stopped at any position between closed and full vent.
Page 127: Wind Buffeting
WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A third outlet is located on the driver’s side, just to the rear of the sliding door and is also controlled by the ignition switch. The lower and rear outlets will not accommodate a conventional cigar lighter unit. The outlets include tethered caps labeled with a key or battery symbol indicating the power source.
Page 129: Electrical Outlet Use With Engine Off
Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 130: Convenience Tray And Optional Smoker's Package Kit
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE into one of the cupholders and then push the arm toward the container until the container is held stable. There are adjustable positions for the arm so the cupholder can accommodate a wide variety of container types and sizes, including those with handles.
Page 131 If your vehicle is equipped with quad seats in the 2nd seat position, these cupholders are located on the out- board side of the seat pedestal. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 NOTE: • The quad seat cupholders will remain upright if the seat is tilted forward.
Page 132: Storage
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Front Seat Storage Bin — If Equipped The storage bin is located under the front passenger’s seat. If equipped with a lock, it can be locked with the ignition key. Removable Floor Console — If Equipped The removal floor console has a power outlet, storage tray, light, cell phone holder, tissue holder, and a map holder.
Page 133 To remove the console use the following procedure: 1. Open the rear lid and remove the storage tray. 2. Pull the release handle located inside the floor console, reinstall the storage tray and close the rear lid. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3.
Page 134 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE forward to engage the front of the console into the floor tray. Rapidly push down on the rear of the console with enough force to engage the latch, you should hear the latch “snap” into place. Pull up on the console to be sure it’s firmly attached.
Page 135: Rear Compartment Storage Bins
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 136: Cargo Organizer - If Equipped
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing. Cargo Organizer — If Equipped Long wheel base vehicle with rear air conditioning may be equipped with a cargo organizer that mounts on the floor behind the rear seat.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 2. Place the rear corners of the cargo organizer into the supports located on the rear trim panel. Press down on the back of the cargo organizer to lock it into place.
Page 138 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not load objects over 20 lbs (9 kg) in the upper position. Failure to follow this warning could cause the cargo organizer to collapse resulting in personal injury. CAUTION! Do not load objects over 100 lbs (45 kg) in the lower position.
Page 139: Roof Luggage Rack - If Equipped
Cargo Organizer removal Unscrew the two plastic fasteners located on the floor of the rear of the cargo area and remove the cargo organizer from the vehicle. NOTE: The cargo organizer must be removed to take out the third row seat. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 ROOF LUGGAGE RACK —...
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the cross bars, press the upper edge of each cross bar button pass the detent, then move the cross bar to the desired position.
Page 141: Load Leveling System
CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appro- priately. • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle.
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the leveled vehicle is not moved for approximately 15 hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system. WARNING! Do not install the load leveling system on vehicles that are not equipped with Anti-Lock Brakes.
Page 143: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....148 Base Instrument Cluster ....149 Instrument Cluster With Tach .
Page 144 144 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch, Volume Control ... . 162 Seek Button (Radio Mode) ....162 Tuning .
Page 145 Program Button 4 (Random Play) ..169 Mode ......169 Tape CD Button .
Page 146 146 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button ......186 Changing Modes ..... . 186 Removing Discs From The CD Changer .
Page 147 Manual Air Conditioning Operation ..203 Manual Rear Zone Climate Control — If Equipped ......206 Infrared Three-Zone Automatic Temperature Control —...
Page 148: Instruments And Controls
148 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 149: Base Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 149 BASE INSTRUMENT CLUSTER...
Page 150: Instrument Cluster With Tach
150 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER WITH TACH...
Page 151: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Low Fuel Light When the fuel level reaches approximately 3.0 gallons (11.0 liters) this light will turn on and remain on until fuel is added.
Page 152 152 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed. If brake failure is indicated, immediate repair is neces- sary. WARNING! Driving a vehicle with the brake light on is danger- ous.
Page 153 8. Anti-Lock Light This light monitors the Anti-Lock Brake System. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 154 154 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Engine Temperature Warning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a continuous chime will sound for 4 minutes. After the chime turns off, the engine will still be critically hot until the light turns off.
Page 155 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph.
Page 156 156 UNDERSTANDING YOUR INSTRUMENT PANEL engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage.
Page 157 20. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can...
Page 158 158 UNDERSTANDING YOUR INSTRUMENT PANEL When the tire pressure monitoring system warning light is lit, one or more of your tires is significantly underin- flated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the tire and loading information placard.
Page 159: Information Center - If Equipped
INFORMATION CENTER — IF EQUIPPED Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a chime UNDERSTANDING YOUR INSTRUMENT PANEL 159 will sound to alert you to turn the signals off.
Page 160: Clock Setting Procedure
160 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Turn the ignition switch to the ON or ACC position and press the time button. Using the tip of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio.
Page 161: Am Reception
AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio.
Page 162: Power Switch, Volume Control
162 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode.
Page 163 Program Type Radio Display News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports...
Page 164: Balance
164 UNDERSTANDING YOUR INSTRUMENT PANEL Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is pressed.
Page 165: To Set The Radio Push-Button Memory
To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
Page 166: Fast Forward (Ff)
166 UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
Page 167: Pinch Roller Release
Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play.
Page 168: Seek Button
168 UNDERSTANDING YOUR INSTRUMENT PANEL If the volume control is ON, the unit will switch from radio to CD mode and begin to play. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: •...
Page 169: Ff/Tune/Rw
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 170: Time Button
170 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press this button to change the display from elapsed CD playing time to time of day. Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. CD Changer Control Capability —...
Page 171: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™...
Page 173 Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out. Adjust the balance and push the button back in. Tone Control The tone controls affect the Bass and Treble frequency bands.
Page 174: Cd Player Operation
174 UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
Page 175 show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load”...
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play.
Page 177 Program Type Radio Display Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports...
Page 178: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
178 UNDERSTANDING YOUR INSTRUMENT PANEL Time Press the TIME button to change the display from elapsed CD playing time to time of day. SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on.
Page 179 the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in.
Page 180: Cd Player Operation
180 UNDERSTANDING YOUR INSTRUMENT PANEL both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed.
Page 181 If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds.
Page 182: Cd Changer Control Capability - If Equipped
182 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SA” will appear in your radio display.
Page 183 Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
Page 184: Radio Display Messages
184 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel.
Page 185: Loading The Cd Changer
Loading the CD Changer When inserting the first CD into the changer if the radio is on, wait until the single slot is illuminated on both sides and simply insert the first disc. To insert additional CDs into the changer, the instructions follow: 1.
Page 186: Mode Button
186 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button Press this button to toggle between radio and cd modes. Program Button 1 Press this button to play the next available disc. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 187: Removing Discs From The Cd Changer
Removing Discs from the CD Changer If there is a single CD in the changer, press the EJT button and the CD will eject. If the CD is not removed within 15 seconds, it will automatically reload into the CD changer. To eject additional CDs from the changer, first select the numbered button where the CD is located and then press the EJT button.
Page 188: Operating Instructions - Cd/Dvd Changer
188 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — CD/DVD Changer Loading The CD/DVD Changer The CD/DVD changer is a multi-disc changer, and will accept up to six discs. Gently insert one disc into the CD/DVD changer with the label facing up. The disc will automatically be pulled into the CD/DVD changer.
Page 189: Eject (Ejt) Button
• If you insert a disc with the ignition ON and the radio OFF, the DVD will automatically be pulled into the DVD changer and the display will show the time of day. EJECT (EJT) Button If there is a single disc in the changer, press the EJT button and the disc will eject.
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL MENU Button This button only functions in the DVD video mode. Press this button once to go to the on-screen menu, press the button a second time to go to the main menu. When the DVD is in stop mode, pressing the menu button for 3 seconds will display the set-up screen.
Page 191: Operating Instructions - Video Screen
Channel Button Press this button to select between channel “A” or channel “B”, or if interference is heard through the headphones. Remote Control Battery Service • To replace the batteries for the remote control slide the cover rearward. The replacement batteries for the remote control are two AAA batteries.
Page 192: Operating Instructions - Headphones
192 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Brightness Button Changes the brightness of the screen picture. Operating Instructions — Headphones 1. ON/OFF Button 2. Scan Button 3. Volume Control 4. LED...
Page 193 Power Button Pressing the power button will turn the headphones ON/OFF. NOTE: • The headphones will turn off automatically and the red LED will illuminate for approximately 2 minutes when the radio or rear audio/video system is turned off. • The rear audio/video system must be turned ON before sound can be heard from the headphones.
Page 194: Operating Instructions - Mp3 Player
194 UNDERSTANDING YOUR INSTRUMENT PANEL Headphone Battery Service • Using a key or similar flat object insert into the slot. • Pry on the release tab to open the cover. • Replace the batteries and reinstall the cover. The replacement batteries for the headphones are three AAA batteries.
Page 195: Operating Instructions - Video Games/Camcorders
NOTE: Follow the manufactures instructions for the correct colors when connecting the RCA cables. Operating Instructions — Video Games/Camcorders A video game unit or camcorder can be connected to the rear audio/video system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer. NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet.
Page 196: Radio Operation
196 UNDERSTANDING YOUR INSTRUMENT PANEL system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of the radio from AM to FM to Tape or CD mode depending on which radio is in the vehicle.
Page 197: Cd Player
CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play.
Page 198: Cd/Dvd Disc Maintenance
198 UNDERSTANDING YOUR INSTRUMENT PANEL turned all the way down. To prevent this, you should periodically clean the head with a commercially available WET cleaning cassette. As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette.
Page 199: Climate Controls
CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Front Blower Control The Front Blower Control selects whether the Cli- mate Control System is ON or OFF. When the blower UNDERSTANDING YOUR INSTRUMENT PANEL 199 control is set to the O (OFF) position the front blower will turn off and the system will be placed in the Recirculation...
Page 200: Front Mode Control
200 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle. This is accomplished by having a separate temperature control lever for both the driver and front seat passenger.
Page 201 Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center UNDERSTANDING YOUR INSTRUMENT PANEL 201 outlets.
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
Page 203: Manual Air Conditioning Operation
Defrost Mode Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or UNDERSTANDING YOUR INSTRUMENT PANEL 203 Defrost modes are selected.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than expected, check the A/C air filter and the front of the A/C condenser for an accumulation of dirt or insects. The A/C condenser is located in front of the radiator. The A/C air filter is located under the instrument panel on the passenger side.
Page 205 A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON. The frequent use of outside air will help keep odors from building up within the air conditioner- heater housing.
Page 206: Manual Rear Zone Climate Control - If Equipped
206 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Rear Zone Climate Control — If Equipped The Manual Rear Zone Climate Control system has floor air outlets to the rear of the right side sliding door and overhead outlets at each outboard rear seating position. The unit provides warm or cool air through the floor and upper outlets.
Page 207 speed positions. This allows the second seat occupants to control the volume of air circulated in the rear of the vehicle. CAUTION! Interior air enters the Manual Rear Zone Climate Control system through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door.
Page 208: Infrared Three-Zone Automatic Temperature Control - If Equipped
208 UNDERSTANDING YOUR INSTRUMENT PANEL temperature selection follows the setting of the driv- er’s temperature control on the front climate control unit. The rear mode selection follows the setting of the front mode control. Rear Economy Mode If rear economy mode is desired, set the center knob on the front control unit to the “REAR”...
Page 209 display along with “HI” or “LO”. The system will then automatically regulate the amount of air flow. Next, dial in the temperature you would like the system to maintain by pressing the driver’s or passenger’s temperature con- trol button. The rear temperature can only be adjusted from the front when the “REAR SYSTEM”...
Page 210 210 UNDERSTANDING YOUR INSTRUMENT PANEL • The “DELAY” symbol will flash to indicate that the feature as been disabled. This feature may be enabled using the following proce- dure: • Press and hold the Heated Rear Window and Auto HI buttons for 5 seconds.
Page 211 Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center UNDERSTANDING YOUR INSTRUMENT PANEL 211 outlets.
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
Page 213 Defrost Mode Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. Depress the “A/C” button to turn on and off the air conditioning during manual operation only. Cool dehumidified air comes through the outlets UNDERSTANDING YOUR INSTRUMENT PANEL 213 selected by the Mode Control.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL improve window clearing operation. Recirculation will be disabled automatically if these modes are selected. Auxiliary Rear Automatic Temperature Control — If Equipped The Rear Automatic Temperature Control System has floor air outlets to the rear of the right side sliding door and overhead outlets at each outboard rear seating position.
Page 215 Operation of the rear system is quite simple. Begin by rotating the rear system center control knob on the front ATC control unit to the “REAR CONTROL” position, this illuminates an “UNLOCK” symbol in the rear display. Next, rotate the Rear Blower Control and the Rear Mode Control to the “AUTO”...
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door. Do not block or place objects directly in front of the inlet grille or heater outlets.
Page 217 Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the head- liner outlets and warmer air from the floor outlets. Headliner Mode Air comes from the outlets in the headliner.
Page 218 218 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Operating Tips Vehicle windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use the Recirculation mode without A/C for long periods as fogging may occur.
Page 219: Rear Window Features
A/C Air Filter — If Equipped The climate control system filters out dust, pollen and some odors from the air. Strong odors can not be totally filtered out. Refer to section 7 “Air Conditioning” for filter replacement instructions. REAR WINDOW FEATURES Intermittent Rear Wiper Operation —...
Page 220: Rear Wiper Operation - Automatic Temperature Control Only
220 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with Automatic Temperature Control, the controls for these features are located in the middle of the instrument panel above the radio. Rear Wiper Operation — Automatic Temperature Control Only Press this button to have the rear wiper have a continuous wipe.
Page 221: Rear Washer Operation - Automatic Temperature Control Only
Rear Washer Operation — Automatic Temperature Control Only Press and hold the button as long as spray is desired. If the switch is depressed while the wipers are on, the wipers will operate for a few seconds after the switch is released then resume the previously set mode of intermittent wiper or continuous wipe.
Page 222: Electric Rear Window Defroster - If Equipped
222 UNDERSTANDING YOUR INSTRUMENT PANEL Electric Rear Window Defroster — If Equipped Press this button to turn on the rear window defroster and the optional heated mirrors. A light will show that the defroster is on. The defroster automati- cally turns off after about 10 minutes of operation. If your vehicle is equipped with Infrared Three-Zone Automatic Temperature Control the rear defroster sym- bol will show in the display screen when the rear...
Page 223: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 226 2.4L Engine ......226 3.3L And 3.8L Engine .
Page 224 224 STARTING AND OPERATING Tire Loading And Tire Pressure ... 247 Tires—General Information ....251 Tire Pressure .
Page 225 Gasoline/Oxygenate Blends ....267 MMT In Gasoline ..... 267 Sulfur In Gasoline .
Page 226: Starting Procedures
226 STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather;...
Page 227 Extremely Cold Weather (below 29°C or insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommended. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 228: 3.3L And 3.8L Engine
228 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released.
Page 229 WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 230: Engine Block Heater - If Equipped
230 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released.
Page 231: Automatic Transmission
WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. STARTING AND OPERATING 231 AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
Page 232: Brake/Transmission Interlock System
232 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 233 Reset Mode - Electronic Transmission The transmission is monitored electronically for abnor- mal conditions. If a condition is detected that could cause damage, the transmission automatically shifts into sec- ond gear. The transmission remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate.
Page 234 234 STARTING AND OPERATING Apply parking brake when leaving vehicle in this range. • “R” Reverse Shift into this range only after the vehicle has come to a complete stop. • “N” Neutral Engine may be started in this range. •...
Page 235: All Wheel Drive - If Equipped
transmission operating temperature exceeds acceptable limits. This is done to prevent transmission damage due to overheating. ALL WHEEL DRIVE — IF EQUIPPED This feature provides full time, on-demand, All Wheel Drive (AWD). The system is automatic with no driver inputs or additional driving skills required. Under nor- mal driving conditions, the front wheels provide most of the traction.
Page 236 236 STARTING AND OPERATING Park position. To release the parking brake, pull out on the parking brake release located on the left side of the instrument panel. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park.
Page 237: Brake System
WARNING! Be sure the parking brake is fully disengaged before driving: failure to do so can lead to brake failure, and an accident. BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function.
Page 238 238 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake Sys- tem. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 239 • and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
Page 240: Power Steering
240 STARTING AND OPERATING All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer. POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces.
Page 241: Traction Control - If Equipped
TRACTION CONTROL — IF EQUIPPED The Traction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction (spinning). The system operates at speeds below 35 mph (56 km/h). The system is always in the “stand by”...
Page 242: Tire Safety Information
242 STARTING AND OPERATING NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC and the OFF indicators located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition.
Page 243 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
Page 244 244 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 245 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 246: Tire Identification Number (Tin)
246 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 247: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. STARTING AND OPERATING 247 Tire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle...
Page 248 248 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 249 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
Page 250 250 STARTING AND OPERATING...
Page 251: Tires-General Information
WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 252: Tire Inflation Pressures
252 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 253 The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation.
Page 254 254 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Page 255: Radial-Ply Tires
Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 256: Tire Spinning
256 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed.
Page 257: Replacement Tires
These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 258: Alignment And Balance
258 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 259: All Wheel Drive (Awd) - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! All Wheel Drive (AWD) vehicles must have the same size and type tires on all wheel positions.
Page 260: 1,2,3, Or 4 Tire(S) Low Pressure
260 STARTING AND OPERATING are significantly underinflated. It is particularly impor- tant, therefore, for you to check the tire pressure in all of your tires regularly and maintain proper pressure. 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 28 psi [1.9 bars] (193 kPa) or less detected in one or more tires.
Page 261: Tire Pressure Now Available
TIRE PRESSURE NOW AVAILABLE The TPM system is functioning normally and the external interference is no longer affecting the system. SPARE TIRE IN USE? YES/NO The TPM system requires more information to determine the correct mode of operation, one or more of the vehicle active tires has been replaced by the spare, a wheel rim not equipped with a TPM sensor or the TPM system requires service.
Page 262 262 STARTING AND OPERATING CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and/or style.
Page 263: General Information
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 264: Snow Tires
264 STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
Page 265: Tire Rotation Recommendations
Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions.
Page 266: Fuel Requirements
If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 267: Gasoline/Oxygenate Blends
The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
Page 268: Sulfur In Gasoline
268 STARTING AND OPERATING It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformu- lated gasolines.
Page 269: Fuel System Cautions
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system, and could result in loss of warranty coverage. •...
Page 270: Adding Fuel
270 STARTING AND OPERATING • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 271 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. NOTE: The driver’s side sliding door cannot be opened while the fuel door is open.
Page 272: Vehicle Loading
272 STARTING AND OPERATING WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive.
Page 273: Gross Vehicle Weight Rating (Gvwr)
• Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo.
Page 274: Loading
274 STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
Page 275: Trailer Towing
Front Axle Empty Weight 2140 lbs Load (Including driver, pass- 360 lbs sengers and cargo) Total 2500 lbs GAWR 2544 lbs TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Page 276 276 STARTING AND OPERATING • The trailer tongue load must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to the Tire– Safety Information Section in this manual.
Page 277 TRAVEL CONDI- MAXIMUM TRAILER WEIGHT (TRAILER FRONTAL AREA NOT TO EXCEED 32 SQ. FT.) TION 2.4L ENGINES MAX. COMBINED WEIGHT OF VE- HICLE AND TRAILER NOT TO EXCEED 5,200 lbs (2358 kg) ALL MODELS UP TO 2 PER- 850 lbs (385 kg) SONS &...
Page 278 278 STARTING AND OPERATING A load equalizing hitch is recommended for loaded trailer weights above 1,000 lbs (454 kg) and required for weights above 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity.
Page 279: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....280 If Your Engine Overheats ....281 Jacking And Tire Changing .
Page 280: Hazard Warning Flasher
280 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the radio. To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 281: If Your Engine Overheats
IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transaxle in neutral, but do not increase engine idle speed.
Page 282: Jacking And Tire Changing
282 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Page 283: Jack Location
Jack Location The jack and jack-handle are stowed behind the rear left side trim panel in the cargo area. Pull up on the lever to release the cover. WHAT TO DO IN EMERGENCIES 283 Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism.
Page 284: Preparations For Jacking
284 WHAT TO DO IN EMERGENCIES Spare Tire Removal Fit the jack-handle over the drive nut. Rotate the nut to the left until the spare is on the ground with enough slack cable to allow you to pull the tire out from under the vehicle.
Page 285: Jacking Instructions
• Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1.
Page 286 286 WHAT TO DO IN EMERGENCIES properly engaged in the described location. Do not raise the vehicle until you are sure the jack is securely engaged. 5. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
Page 287 about the correct tightness, have them checked with a torque wrench by your dealer or at a service station. 10. Lower the jack to its fully closed position. WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle.
Page 288: Jump-Starting Procedures If Battery Is Low
288 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES IF BATTERY IS WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. WARNING! •...
Page 289 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach and without letting the vehicles touch.
Page 290: Driving On Slippery Surfaces
290 WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels.
Page 291: Freeing A Stuck Vehicle
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and Drive.
Page 292 292 WHAT TO DO IN EMERGENCIES km/h). Exceeding these towing limits may cause a trans- mission geartrain failure. If the transmission is not op- erative, or if the vehicle is to be towed more than 100 miles (160 km), the vehicle must be towed with the front wheels off the ground.
Page 293: Without The Ignition Key
If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transmission remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
Page 295 MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine ......298 3.3L/3.8L Engines ..... . 299 Onboard Diagnostic System —...
Page 296 296 MAINTAINING YOUR VEHICLE Front Suspension Ball Joints ....314 Steering Shaft Seal ....314 Steering Linkage .
Page 297 Front Park/Turn Signal And Sidemarker Lights ......340 Front Fog Light ..... . 341 Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights .
Page 298: 2.4L Engine
298 MAINTAINING YOUR VEHICLE 2.4L ENGINE...
Page 299: 3.3L/3.8L Engines
MAINTAINING YOUR VEHICLE 299 3.3L/3.8L ENGINES...
Page 300: Onboard Diagnostic System - Obd Ii
300 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 301: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready...
Page 302: Replacement Parts
302 MAINTAINING YOUR VEHICLE ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
Page 303: Maintenance Procedures
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 304 304 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 305 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). •...
Page 306 306 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only recommends API Certified engine oils that meet DaimlerChrysler Material Stan- dard MS-6395.
Page 307: Engine Oil Filter
Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that meet the Ameri- can Petroleum Institute (API) and SAE viscosity stan- dard.
Page 308: Spark Plugs
308 MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, or glazing, and replaced if there is indication of damage which could result in belt failure. If adjustment is re- quired, the belts must be adjusted according to the specifications and procedures described in the Service Manual.
Page 309: Engine Fuel Filter
WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed.
Page 310 310 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 311: Maintenance-Free Battery
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle.
Page 312: Air Conditioner
312 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and identified on the battery case.
Page 313 WARNING! • Use only refrigerants approved by this manufac- turer for your air conditioning system. Some un- approved refrigerants are flammable and can ex- plode, injuring you. Other refrigerants can cause the system to fail, requiring costly repairs. • Never add air conditioning refrigerant to correct a non-cooling problem unless pressure gauges are connected to the system by a certified technician.
Page 314: Power Steering - Fluid Check
314 MAINTAINING YOUR VEHICLE Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
Page 315: Steering Linkage
Steering Linkage The tie rod end ball joints are permanently lubricated and do not require periodic maintenance. Drive Shaft Universal Joints Your vehicle has constant velocity universal joints. Peri- odic lubrication of these joints is not required. However, the joint boots should be inspected for external leakage or damage when other maintenance is performed.
Page 316: Windshield Wiper Blades
316 MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accu- mulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
Page 317: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken,...
Page 318: Cooling System
318 MAINTAINING YOUR VEHICLE Cooling System Inspection WARNING! • When working near the radiator cooling fan, turn the ignition key to the OFF position. The fan is temperature controlled and can start at any time when the ignition key is in the ON position. •...
Page 319 from the radiator drain cock. If the cap is sealing prop- erly, the coolant will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System — Drain, Flush and Refill At the intervals shown in the maintenance schedules, the system should be drained, flushed and refilled.
Page 320 320 MAINTAINING YOUR VEHICLE Adding Coolant When adding coolant, or refilling the system, a minimum of 50% solution of ethylene glycol antifreeze coolant in water should be used. Higher concentrations (not to exceed 70%) are required if temperatures below ( 38°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/antifreeze solution.
Page 321 Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground.
Page 322: Hoses And Vacuum/Vapor Harnesses
322 MAINTAINING YOUR VEHICLE • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks.
Page 323: Brakes
Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
Page 324: Master Cylinder - Abs Brakes Brake Fluid Level Check
324 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to facilitate the assembly of hoses to couplings.
Page 325 Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear.
Page 326: Fuel System Hoses
326 MAINTAINING YOUR VEHICLE Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline. You are urged to use only the manufacturers specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing.
Page 327 CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 328 328 MAINTAINING YOUR VEHICLE 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips.
Page 329: All Wheel Drive (Awd)
NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules. If the transmission is disassembled for any reason, the fluid and filter should be changed. Special Additives Do not add any fluid additives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks.
Page 330: Front And Rear Wheel Bearings
330 MAINTAINING YOUR VEHICLE transmission fluid, refer to Recommended Fluids, Lubri- cants and Genuine Parts for correct fluid type. To assure performance, it is important that the proper lubricant be used. Rear Carrier The fluid should be maintained at the bottom of the filler hole opening.
Page 331 trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection.
Page 332 332 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
Page 333 • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle.
Page 334: Cleaning The Instrument Panel And Underseat Cup Holders
334 MAINTAINING YOUR VEHICLE defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instru- ments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.
Page 335 Press the stop tab, slide the entire drawer out and remove it from the instrument panel. MAINTAINING YOUR VEHICLE 335 Cleaning Soak the drawer, with the drawer front facing up, in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap.
Page 336: Integrated Power Module (Ipm)
336 MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the battery. This center contains fuses and relays. A label that identifies each component is printed on the inside of the cover. CAUTION! •...
Page 337: Vehicle Storage
The Heated Mirrors, Lower Instrument Panel Power Outlet and Removable Floor Console, when in the front position are fused with self resetting fuses that are only serviceable by an authorized dealer. The power seats are fused by a 30 Amp circuit breaker located under the driver’s seat.
Page 338: Replacement Light Bulbs
338 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Center & Rear Dome Light ....578 Center & Rear Reading Lights ....578 Front Door Courtesy Light .
Page 339: Bulb Replacement
BULB REPLACEMENT Headlights 1. Remove the three screws securing the headlight mod- ule. 2. Turn the bulb socket retaining ring counterclockwise. MAINTAINING YOUR VEHICLE 339 3. Disconnect the electrical connector and replace the bulb.
Page 340: Front Park/Turn Signal And Sidemarker Lights
340 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Front Park/Turn Signal and Sidemarker Lights 1.
Page 341: Front Fog Light
3. Replace bulb, reinstall socket and then reinstall the headlight module. MAINTAINING YOUR VEHICLE 341 Front Fog Light 1. Reach behind the front fascia from under the vehicle. 2. Twist the front fog light bulb to remove from the fog light module.
Page 342: Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights
342 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two light assembly push-in type fasteners. 3. Squeeze the socket assembly tabs to remove it from the housing. 4. Pull the bulb to remove it from the socket. 5.
Page 343: Center High Mounted Stop Light (Chmsl)
Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
Page 344: Recommended Fluids, Lubricants And Genuine Parts
344 MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Oil Filter 2.4 liter engines Oil Filter 3.3/3.8 liter engines Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Use API Certified, meeting material standard MS-6395, (GF-3).
Page 345: Chassis
Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Overrunning Clutch AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid. Mopar Gear Lubricant 75W-90. Mopar ATF+4 Automatic Transmission Fluid. Mopar Gear Lubricant 75W-90. Mopar DOT 3 and SAE J1703 should be used.
Page 347 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..348 Maintenance Schedules ....348 Schedule “B” ......351 Schedule “A”...
Page 348: Emission Control System Maintenance
348 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 349 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. NOTE: Most vehicles are operated under the conditions listed for Schedule B . Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Sched- ule B .
Page 350 350 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake hoses. • Inspect the CV joints and front suspension compo- nents. • Check the automatic transmission fluid level. •...
Page 351: Schedule "B" 351
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 352 352 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Inspect and adjust the power steering pump belt tension on 2.4 liter engines.
Page 353 Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs 2.4 liter engines. Inspect the tie rod ends and boot seals. Inspect and adjust the power steering pump belt tension on 2.4 liter engines.
Page 354 354 SCHEDULE “B” Miles (Kilometers) Change the All Wheel Drive (AWD) overrun- ning clutch and rear carrier fluid. (See the note at the end of this chart) Replace the air conditioning filter. 21, 000 24, 000 27, 000 30, 000 (34 000) (38 000) (43 000)
Page 355 Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. * Inspect and adjust the power steering pump belt tension on 2.4 liter engines. Inspect the generator belt on 2.4 liter engines, replace if necessary.
Page 356 356 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs on 2.4 liter engines. Replace the ignition cables on 2.4 liter en- gines.
Page 357 Miles (Kilometers) Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary. Change the automatic transaxle fluid and fil- ter. Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrun- ning clutch and rear carrier fluid.
Page 358 358 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs on 3.3 liter and 3.8 liter engines.
Page 359 Miles (Kilometers) Inspect engine accessory drive belts on 3.3 li- ter and 3.8 liter engines, replace if necessary. ‡ Check the PCV valve and replace if necessary. Not required if previously changed.* Change the All Wheel Drive power transfer unit fluid. (See the note at the end of this chart.) Change the All Wheel Drive (AWD) overrun- ning clutch and rear carrier fluid.
Page 360 360 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Inspect and adjust the power steering pump belt tension on 2.4 liter engines. Inspect the generator belt on 2.4 liter engines, replace if necessary.
Page 361 Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Replace the spark plugs on 2.4 liter engines. Replace the ignition cables on 2.4 liter engines. Inspect and adjust the power steering pump belt tension on 2.4 liter engines.
Page 362 362 SCHEDULE “B” Miles (Kilometers) Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Replace the air conditioning filter. * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty.
Page 363: Schedule "A
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs on 2.4 liter engines. Inspect the tie rod ends and boot seals.
Page 364 364 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs on 2.4 liter engines. Replace the ignition cables 2.4 liter engines.
Page 365 Miles (Kilometers) [Months] Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary. ‡ Flush and replace the engine coolant at 60 months, regardless of mileage. Replace the air conditioning filter. 42, 000 48, 000 54, 000 60, 000 (67 000)
Page 366 366 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if neces- sary. * Replace the engine air cleaner filter. Replace the spark plugs on 2.4 liter engines. Inspect the tie rod ends and boot seals.
Page 367 Miles (Kilometers) [Months] Replace the spark plugs 3.3 liter and 3.8 liter en- gines. Replace the ignition cables 3.3 liter and 3.8 liter engines. Flush and replace the engine coolant at 100,000 miles, if not done at 60 months. Replace the air conditioning filter. 78, 000 84, 000 90, 000...
Page 368 368 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs on 2.4 liter engines. Replace the ignition cables 2.4 liter engines.
Page 369 Miles (Kilometers) [Months] Flush and replace the engine coolant at 120 months, if not done at 100,000 miles (160 000 km). Replace the air conditioning filter. * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty.
Page 371: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......372 Prepare For The Appointment .
Page 372: Suggestions For Obtaining Service For Your Vehicle
372 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 373 The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf.
Page 374 374 IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni-...
Page 375: Warranty Information
Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
Page 376: Reporting Safety Defects
376 IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 377 • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts.
Page 378: Department Of Transportation Uniform Tire Quality Grades
378 IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
Page 379: Temperature Grades
Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 381 INDEX...
Page 382 382 INDEX Adding Fuel ......270 Adding Washer Fluid ....221,316 Additives, Fuel .
Page 383 Filter ....... 328 Fluid and Filter Changes ....328 Fluid Level Check .
Page 384 384 INDEX Cargo Compartment Luggage Carrier ..... . . 139 Cassette Tape and Player Maintenance ..197 Cassette Tape Player .
Page 385 Radiator Cap ......320 Selection of Coolant ....319,344 Cruise Control .
Page 386 386 INDEX Air Cleaner Filter ..... . 308 Block Heater ......230 Break-In Recommendations .
Page 387 Fuel ....... . . 266 Adding ......270 Additives .
Page 388 388 INDEX High Beam/Low Beam Select Switch ..103 Lights On Reminder ....101 Replacing .
Page 389 Key-In Reminder ......13 Keyless Entry System ..... . 20 Keys .
Page 390 390 INDEX Malfunction Indicator ....155 Oil Pressure ......155 Park .
Page 391 Automatic Dimming ..... 77 Electric Remote ......79 Exterior Folding .
Page 392 392 INDEX Panic Alarm ......22 Parking Brake ......235 Parking On Hill .
Page 393 Rear Window Features ....219 Rear Wiper/Washer ....219,220,221 Rearview Mirrors .
Page 394 394 INDEX Bench ......90,92 Easy Entry ......85 Easy-Out Roller .
Page 395 Steering Wheel Mounted Sound System Controls ......195 Storage ......132,337 Storage Bin .
Page 396 396 INDEX Sizes ....... 244 Snow Tires ......264 Spare Tire .
Page 397 Vehicle Information Center ....115 Vehicle Loading ..... . 272,274 Vehicle Modifications/Alterations .

This manual is also suitable for:

2004 rs caravan

Dodge 2004 Caravan Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2004 Caravan

Summary of Contents for Dodge 2004 Caravan