Table of Contents
Advertisement
Timer recording
Refer to the control reference on page 17.
[RAM] [DVD-R]
You can enter up to 16 programmes up to a month in advance.
(Each daily or weekly programme is counted as one programme.)
Manually programming timer
recordings
1
Press [PROG/CHECK].
TIMER
RECORDING
No. Name
Date
Start
01
ARD
15/ 7 TUE
19:00
New Timer Programme
SELECT
ENTER
RETURN
2
Press [3, 4] to select "New Timer
Programme" and press [ENTER].
3
Press [1] to move through the items
and change the items with [3, 4].
TIMER
RECORDING
Name
Date
Start
1 ARD
15/ 7 TUE
22:00
≥Press and hold [3, 4] to alter the Start (Start time) and
Stop (Finish time) in 30-minute increments.
≥You can also set Name (Programme position/TV Station
Name), Date, Start (Start time), and Stop (Finish time) with
the numbered buttons.
≥You can also press [REC MODE] to change the recording
mode.
≥Date
[.
Date:
Current date up to one month later minus
l
;:
one day
l
Daily timer:
SUN-SAT>MON-SAT>MON-FRI
l
;:
a.
Weekly timer: SUN>--->SAT
≥Programme Name ( page 32)
Press [2, 1] to select "Programme Name" and press
[ENTER].
4
Press [ENTER].
TIMER
RECORDING
No. Name
Date
Start
01
ARD
15/ 7 TUE
19:00
02
ARD
15/ 7 TUE
22:00
New Timer Programme
Repeat steps 2–4 to programme other recordings.
5
Press [F TIMER].
The unit turns off and "F" lights on the unit's display to
indicate timer recording standby has been activated.
RQT7444
18
Remain
1:58 SP
12:56:00 15. 7. TUE
Disc
Stop
Mode
space
20:00
SP
OK
Press ENTER to store
new programme.
Remain
1:58 SP
12:57:00 15. 7. TUE
Stop
Mode
22:30
SP
Programme Name
Remain
1:58 SP
12:58:00 15. 7. TUE
Disc
Stop
Mode
space
20:00
SP OK
Check to make sure
22:30
SP OK
"OK" is displayed.
[RAM]
Even if the unit is in timer recording standby, play starts when you
press [1] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
∫ To release the unit from recording standby
Press [F TIMER].
The unit turns on and "F" goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if "F" is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
≥You can also press and hold [∫] on the main unit for more than
3 seconds to stop recording.
[Note]
≥"F" flashes for about 5 seconds when the unit cannot go to
timer recording standby (e.g., a recordable disc is not in the
disc tray).
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the "F" flashes on the unit display. In this case,
press [F TIMER] to put the unit in the timer recording standby
mode.
≥When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R).
Hide quick links:
Advertisement
Table of Contents
