Desa SBVBN(C) Owner's Operation And Installation Manual page 20

OPERATING STOVE WITH B-VENT BURNER SYSTEM
20
Optional Remote Operation
OPERATING STOVE WITH
B-VENT BURNER SYSTEM
Continued
OPTIONAL REMOTE
OPERATION
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 32). Follow instructions included
with the remote control.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instruc-
tions, page 19.
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide the selector switch
to the REMOTE position (see Figure 49). Note: The burner
may light if hand-held remote was on when selector switch
was last turned off. You can now turn the burner on and off
with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the RE-
MOTE or ON position when the pilot is not lit. This will
drain the battery.
Selector Switch
in Remote
Position
(Optional
Remote Control)
Control Knob in On Position
Figure 49 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
ON/OFF SERIES
(MODELS GHRCB AND CGHRCB)
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 50).
TO LOCK press both buttons on hand-held remote control until
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
press both buttons together on hand-held remote
TO UNLOCK
control until the light stops flashing. The hand-held remote is
now unlocked.
Figure 50 - On/Off Hand-Held Remote Control Unit (C)GHRCB
For more information, visit www.desatech.com
For more information, visit www.desatech.com
THERMOSTAT SERIES
(MODELS GHRCTB AND CGHRCTB)
The hand-held remote can be operated using either the manual mode
(MANU) or thermostatic mode (AUTO) (see Figure 51). To select
Fahrenheit/Centigrade mode display, carefully press the ˚C/˚F mode
button with the end of a paper clip or similar blunt object.
Manual Mode
1. Press the POWER and LOCK buttons together to turn on
2. Press the MANU button to turn on the fireplace.
3. Press the POWER and LOCK buttons together to turn off
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons together to turn on
2. Press AUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP
4. Press the POWER and LOCK buttons together to turn off
Note: Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turn off the fireplace. Ideally, place the hand-held remote in the
center of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Digital Display
Shows
Temperature and
Settings
Turns Burners
On or Off
Decreases Room
Temperature in
AUTO Mode
Figure 51 - Thermostat Hand-Held Remote Control Unit
Selections (C)GHRCTB
Safety Features
Control Button
When away from home for an extended period of time or as a
Turns Burners
child safety feature to prevent accidental ignition of the fire-
On and Off
place, the receiver ON/OFF/REMOTE switch should be in the
OFF position.
the hand-held remote control.
the fireplace.
the hand-held remote control.
+ or - buttons.
the fireplace
Turns Remote On
or Off and Allows
You to Choose the
Manual Setting
Selects Auto
Setting
Increases Room
Temperature in
AUTO Mode
Locks System to
Prevent Accidental
Ignition
106828-01C