Summary of Contents for Kenmore 3247 - Elite 36 in. Gas Cooktop
Page 1
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal...
Page 2
Important Notes to the Installer • Be sure your cooktop is instaJJed and grounded Read all instructions contained in these installation properly by a qualified installer or service technician. instructions before installing the cooktop. Remove all packing material before connecting the This cooktop must be electrically...
Page 3
13" (33 cm) Max. Depth For Cabinet 30" (76.2 cm) Installed Above Min, Clearance Cooktop. Between the Top of the Cooking Platform and Unprotected Wood or Metal 11/2" (3.8 cm)Minimum Distance Clearance Cabinet Between Rear Edge of Cutout and Nearest Combustible Surface Above Countertop, 18"...
Page 4
Typical Gas Cooktop Installation Over an Electric Built-in Oven Installed Under the Counter I_---- 18" (45.7 cm) Max.-----_ 4" (10.2 cm) 61_2" Manifold Pi 5" ,(16.5 cm) Flare (12.7cm) Min. Union 120V/60Hz Flexible Connector Grounded Right Side of Flare Outlet Cabinet Union Pressure...
Page 5
Typical Under Counter Installation of an Electric Built-in Oven with a Cooktop Mounted Above Side filler panels are necessary to isolate the unit from adjoining cabinets. Panel height should allow for installation of approved cooktop This cooktop may models. See "Typical Gas Cooktop be installed over Installation Over an Electric Built-in certain built-in elec-...
Page 6
Wall Outlet Location To clamp down, insert an angle bracket into the slot on each side of the unit as shown.Run thumb screw up through the bracket, up against the bottom of the counter. Tighten until the unit draws down and is secure. 12"_ Provide an Adequate...
Page 7
Important: Remove a llpacking material and The supply line must be equipped with an approved manual shutoff valve. This valve should be located in the literature fromcooktop before connecting g asand electrical supply to cooktop. same room as the cooktop and should be in a location that allows ease of opening and closing.
Page 8
Electrical Requirements C. Place a burner cap on each burner head, matching the cap size to the head size. Each burner cap has an 120 volt, 60 Hertz, properly grounded branch circuit inner locating ring which centers the cap correctly on protected by a 15 amp circuit breaker or time delay fuse.
Page 9
4.Adjustthe 5. Adjust the "LOW" Setting of the Bridge Burner "low" setting for regular surface burner Surface Valve (Figure g) (some models): valves(Figure g) Note: On the dual valve the low setting of each portion a. Push in and turn control to LITE until burner ignites. (rear portion of bridge burner and the center portion of b.
Page 10
LA INSTALACION Y EL SERVICIO DEBEN SER REAUZADOS POR UN INSTALADOR CALiFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL iNSPECTOR ELECTRICO LOCAL. LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS Si todas las instrucciones de este manual no son observadas a la letra, se puede ocurrir...
Page 11
que la plancha de cocinar sea instalada ,,Aseg_rese Notas importantes para el instalador: I. Lea todas las instrucciones de instalaci6n antes de y puesta a tierra correctamente pot un instalador o t&cnico calificado. realizar la instalaciOn de la plancha de cocinar. 2.
Page 12
Max, p rofundidad degabinetes instalados por encima dela plancha d e 30" (76.2 cm) ¢ Minimo de empotar es13" (33cm). espacio entre la parte 1Y2" ( 3.8cm)Minimo Distancia superio de la entreelhorde posterior del Espacio plataforma de hueco y la mas cerca superficie la plancha de combustible porencima del 18"Min.
Page 13
Instalaci6n tipica de la plancha de cocinar a gas pot encima de un homo el6ctrico empotrado instalado debajo del mostrador 4" (10.2cm) 61/2 '' Tubo mOIti 5" (13.5 cm) (12.7cm) Min. Uni6n Lado derecho :'"',, Uni6n del armario Conector flexible 120V/60Hz Toma de Uni6n...
Page 14
Tipica instalaci6n de un horno el6ctrico empotrado con una plancha de cocinar por encima Entrepar_os Ilenador de lados son necesarios para aislar el aparato de los armarios adyacentes. La altura de panel debe de permitir la instalacion de Todas las fijaciones de modelos de planchas de cocinar montaje deben de estar aprobantes.
Page 15
Ubicaci6n de la toma de corriente de la pared Para ajustar el aparato, inserte la consola de escuadra, con el lado desviado,en las ranuras en cada lado del aparato. El tornillo de orejas debe entonces de pasar a tray,s del 1 2 It soporte y hasta la parte de abajo del mostrador.
Page 16
Instalad6n deJ regulador de presi6n Instale el regulador de presiOn con la flecha del regulador apuntando hacia la unidad en una posiciOn que permita alcanzar la tapa de entrada. No ajuste demasiado la conexiOn. regular esta fundida a presiOn. AI ajustar demasiado se puede romper el regulador causando una fuga de gas y un posible incendio o explosion.
Page 17
Requerimientos eJectricos Anillo de Un circuito derivado conectado correctamente a tierra de localizaci6n 120 voltios, 60 Herz protegido por un interruptor automatico de 15 amp o un fusible de retardo. No utilice un cable flexible de extensi6n en esta plancha de Tapa del cocinar.
Page 18
Ajuste bajo ("LO") ara la v_lvula de los quemadores En sentido de las de superficie (Figura 9) manecillas a. Presione y gire el control hasta la posici6n LITEpara reloj prender los quemadores. En sentido opuesto _ a las manecillas b. Gire r,_pidamente gire la perilla a la POSICIONMAS BAJA.
Page 19
TOP Bb_NER LGN I TER CAUTION: OPT [ ONAL LABEL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS OLJEMADOR DE E'\OEND DO SUPERIOR DPC I ONAL _IRIM] E_OR CAN CAbbiE [_R{_ER DANGEWOb<_ OPTRATION _:)UG I E D' ALLb,_AGE BRL_ EUR VERIFY PROPER ORERA_]_ AFTER DERVICIKG...