Important Safety Instructions When using your projector, always follow basic safety precautions: 1. Read and understand all instructions before using this equipment. 2. Operate this projector with 110- to 125-volt 60 Hz current only. Incorrect voltage can cause projector malfunction. 3.
The serial number of your projector is printed on the label affixed to the power cord retainer on the base of the projector. Record this number, as well as the model identification, date, and place of purchase, for future reference. KODAK CAROUSEL® Slide Projector...
Introduction Congratulations! You have just purchased a KODAK CAROUSEL Slide Projector which: • triples lamp life • provides brighter and more vivid colors! Introduction Take the time to read the instructions in this operating manual to become ® familiar with your KODAK CAROUSEL Slide Projector and how to operate it properly.
Open the storage compartment and remove the remote control. Plug the 5-pin cable remote connector into the remote-control receptacle, aligning the raised dot with the metallic rivet head. Plug the power cord into a grounded outlet with 110- to 125-volt 60 Hz current only. KODAK CAROUSEL® Slide Projector...
Operation Loading the Slide Tray KODAK Slide Trays are available in 80- and 140-slide capacities. Use a 140-slide tray if you use thin-mounted slides (1/16 in. / 1.6 mm) and need the larger capacity. Use an 80 cpacity tray if any of your slides have thick mounts (1/8 in.
Page 10
Insert your first slide into the first slot in the tray so that the number is visible on the outer circumference of the tray. Insert your second slide in the second slot with the emulsion (dull side) facing your first slide, and so on. KODAK CAROUSEL® Slide Projector...
Page 11
Replace the lock ring by turning it clockwise until it is secure Tray Place the loaded slide tray on the projector. Align the tray index bar with the gate index. The tray will drop into position. KODAK CAROUSEL® Slide Projector...
Page 12
Operation Removing the Tray To remove the slide tray: press the all the way down • select bar align the with the • tray index bar gate index You can then lift off the tray. KODAK CAROUSEL® Slide Projector...
Projecting Your Slides Lens To insert a lens, push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector. Lamp Slide the power switch to lamp. KODAK CAROUSEL® Slide Projector...
Page 14
Models 4400 and 5600. Random Projection For random projection of any slide in the tray: press and hold down the • select bar rotate the tray to the desired slide, • release the select bar. • KODAK CAROUSEL® Slide Projector...
Page 15
To time your slides, use the timer switch for slide changes from 3 to 22 seconds. (Model 5600 only) To interrupt the timer, press either the forward or reverse button. For manual operation, slide the timer switch to Off. KODAK CAROUSEL® Slide Projector...
Page 16
(when a darkened room is required). When you turn the projector off at the end of your presentation, the room light will come on again. KODAK CAROUSEL® Slide Projector...
Page 17
Also, a curved-field lens, in combination with cardboard open face mounts from an automated mounting process, provide superior projection quality. A flat-field lens is the best choice for glass-mounted slides. KODAK CAROUSEL® Slide Projector...
Page 18
• duplicated slides A curved-field lens works best for: embos • sed cardboard mounts (Embossed mounts have beveled edges around the aperture. Kodak labs provide embossed Premium Processing and Kodak Processing mounts.) Lens Focal Length/ Use the illustration on the following page to help determine the lens focal Projector Distance length and projector distance.
Adding a Slide When the lock ring is off, you can add a slide to any empty slot. (See “Adding Your Slides” on page 6.) Replace and secure the lock ring. KODAK CAROUSEL® Slide Projector...
Put the tray aside. Remove the slide or object from the projector gate by pressing the forward button or removing the slide manually. Remount damaged slides to protect your projector and slides from subsequent damage. KODAK CAROUSEL® Slide Projector...
Grasp the viewer handle and pull it out from the base of the projector. It will Viewer pop into place. Slide the power switch to lamp to project your slides. Closing the Viewer To close the viewer, fold it and push it back into the body of the projector. KODAK CAROUSEL® Slide Projector...
Lens on the lens barrel with the notch on the projector. Shutdown To shut down, • remove and store the tray • slide the power switch to off Your projector will remain warm for several minutes. KODAK CAROUSEL® Slide Projector...
EXY (200 hours/less brightness) EXR (35 hours/maximum brightness) Note: An EXW lamp is not recommended for older models of CAROUSEL Projectors. Contact the Kodak Information Center at 1-800-242-2424 in the U.S. or 1-800-465-6325 in Canada if you need help identifying your particular model.
Insert a new lamp into the socket. Push down to tightly seat the replacement lamp. Relatch the clip in the forward position and push the lamp module all the way back into the projector until it latches. KODAK CAROUSEL® Slide Projector...
Use a torx-head screwdriver to remove the screw. Using a flat-blade screwdriver, apply ample pressure to release each of the metal tabs. Lift off the top of the lamp module. KODAK CAROUSEL® Slide Projector...
Page 27
You can clean the condenser lens in place, or by pulling it out. Wear gloves to prevent fingerprints. Caution Heat-Absorbing The heat-absorbing glass is fragile. Handle it only when cool. Glass (For lamp modules The green-tinted heat-absorbing glass easily removes for cleaning. with a heat-absorbing glass.) KODAK CAROUSEL® Slide Projector...
Page 28
Start with the tabs in the rear of the lamp module. Insert the remainder of the tabs into slots until all 7 tabs on the top and 2 on the bottom are secured. Insert the screw and tighten. Then insert and seat the lamp. KODAK CAROUSEL® Slide Projector...
Page 29
To clean the mirror, invert the lamp module to reach the mirror. Gently clean the mirror with a soft, lint-free cloth moistened with lens cleaner. When your maintenance is complete, push the lamp module back into the projector. KODAK CAROUSEL® Slide Projector...
Curved field lens used for rear Use a flat field lens. projection Lamp performance UInstall new lamp and try again. Autofocus has difficulty slide to slide Mixed open and glass slide mounts Do not mix open and glass mounts KODAK CAROUSEL® Slide Projector...
Page 31
Check slide position and slide- projector gate mount condition. Projector won't cycle to next slide Tray not properly positioned Reposition tray. Slide or foreign object stuck in gate See "Clearing a Gate Jam" on page 17. KODAK CAROUSEL® Slide Projector...
Kodak will repair it without charge, except for worn-out projector lamps. If Kodak is unable to repair the projector, the option of replacement or refund of the purchase price will be available.
How to Obtain Service Assistance To obtain service or for assistance in using your KODAK CAROUSEL Slide Projector, contact the Kodak Information Center at 1-800-242-2424, Monday through Friday, 8 a.m. to 8 p.m. (Eastern time). In Canada, call 1-800-465-6325, Monday through Friday, 8:30 a.m. to 5 p.m. (Eastern time).