Part Names And Functions - Denon DRA-F101 Operating Instructions Manual

ENGLISH
5

PART NAMES AND FUNCTIONS

(1) Front Panel
q
Power operation switch (ON/STANDBY)
• This turns the power for the entire system on and
off.
• Press this once to turn the power on, then press
again to set the power to STANDBY mode.
• The LED color changes as follows, according to
the condition:
During power ON : green
During STANDBY : red
During TIMER STANDBY: orange
The muting mode is set when the main unit's
power button is pressed and when the standby
mode is canceled from the remote control unit.
The power indicator flashes green when in the
muting mode, then stops flashing and turns green
once the set is in the operational mode.
If the indicator is flashing orange (quickly):
The protective circuit is activated.
If this happens, unplug the power cord to turn the
indicator off, then check the input and output
terminals on the rear panel. Check in particular for
short-circuiting of the speaker cords. Once all
connections have been corrected, plug the power
cord. (Wait for at least 10 seconds after turning
the power off before turning it back on.)
• When the DRA-F101 is connected in a system
with the DCD-F101, its power button works as the
power button for the entire system. When the
DRA-F101's power turns on, the power of the
DCD-F101 also turns on.
Power is supplied to the DRA-F101 even when
the power is in the standby mode (low power
consumption).
w
REMOTE SENSOR (Remote Control Sensor)
• Point the included remote control unit (RC-927) at
this sensor when operating it.
e
Headphones jack (PHONES)
• Use this jack to listen to the sound over
commercially available headphones.
• When the headphones' plug is inserted into the
jack, the speaker output is automatically cut off,
so no sound is produced from the speakers.
r
Function dial (FUNCTION)
• Switches the input function. Also used to set the
modes selected with the mode button.
(See pages 12, 13.)
t
Display
Refer to page 9.
8
y
Volume control dial (VOLUME)
• Use this to adjust the overall volume. (Rotary
Encoder System).
• The volume increases when the control is turned
clockwise (, ), decreases when it is turned
counterclockwise (.).
• The volume increases and decreases in 63 steps
from the minimum (VOLUME 0) to the maximum
(VOLUME MAX).
u
Source direct button (SOURCE DIRECT)
• When pressed and set to the "ON" position, the
tone control (bass, treble, balance and loudness)
circuits are set into default condition.
• When pressed again and set to the "OFF"
position, the signals pass through the tone control
circuits, so the tone (bass, treble, balance and
loudness) can be adjusted as desired.
i
Band button (BAND)
• Each time this button is pressed, the band and FM
reception mode change as follows.
FM AUTO FM MONO AM
o
Tuning buttons
(TUNING UP AND DOWN)
• Use these buttons to tune in AM and FM stations.
(TUNING UP/DOWN) (See page 13.)
!0
Memory/set button (MEMORY/SET)
• Use this as the memory button when presetting
AM and FM stations.
• Use this as the set button when setting the time
and timer and when inputting data.
• When the PTY search mode, press this button to
select the type of program.
!1
Display button (DISPLAY)
Each time this button is pressed, the display
changes as follows:
TIME FUNCTION
!2
Timer button (TIMER)
• Press this button during power ON mode to
confirm or change the display. Each time this
button is pressed, the display changes as follows:
FUNCTION CLOCK
TIMER STANDBY
CLOCK: Indicates the current time.
TIMER STANDBY: Indicates the timer standby
mode. Use the TUNING buttons to set the timer
standby mode on or off (refer to page 16).
• Press this buttons for at least 3 seconds to set the
timer (refer to page 15) or to confirm the timer
contents (refer to page 16).
Each time the TUNING button is pressed, the
display changes as follows:
TIME EVERYDAY ONCE
TIME: Use this to set the time.
EVERYDAY: Use this to set the everyday timer.
ONCE: Use this to set the once timer.
• Press this button during in STANDBY mode to
switch ON/OFF ("Saving Energy Mode") the clock
display.
!3
Tone button (TONE)
• Use this to set the bass, treble and balance level.
(Refer to pages 12, 13.)
• Use this to set the loudness function to on or off.
(Refer to page 13.)
(2) Rear Panel
!4
SIGNAL GND (ground) terminal
• Connect the turntable's ground wire here.
NOTE:
• This terminal is designed to reduce noise
when a turntable is connected.
This is not a safety ground.
!5
INPUT terminals (INPUTS)
These are input terminals for CD player, turntable,
DVD or other playback components.
!6
TAPE and MD PLAY terminals (PB)
• Playback terminals (PB)
!7
TAPE and MD REC terminals (REC)
• Recording terminals (REC)
• These are output jacks for recording.
• TAPE:
Use these to connect a cassette deck.
• MD:
Use these to connect an MD recorder
!8
PRE OUT terminal (SUB WOOFER)
• Connector jack for subwoofer with built-in
amplifier (super woofer), etc.
!9
AC OUTLET
• When using in combination with the DCD-F101,
connect DCD-F101 to the AC outlet on the
receiver (DRA-F101).
@0
Power cord
• Plug this cord into a wall power outlet.
@1
Speaker terminals
(SPEAKER SYSTEM)
• Use these to connect the speakers.
@2
System connectors
(SYSTEM CONNECTOR 1 and 2)
• When connecting the DCD-F101 in a system,
connect these connectors to system connectors
on DCD-F101.
(Use the system cord included with the DCD-
F101.)
@3
AM antenna terminal
(ANTENNA TERMINAL AM)
• Connect the AM antenna here.
@4
FM antenna terminal
(ANTENNA TERMINAL FM)
• Connect the FM antenna here.