Expression Pedal; Lfos; Factory Reset - DigiTech RP355_E - REV 18-6412V-D Owner's Manual

7. The Expression Pedal will control output level of the recorded phrase.
8. To stop or restart the playback, press the Down (Stop/Play) Footswitch.
9. To record a new passage, press the Amp A/B (Record) Footswitch again.
10. To exit Learn-A-Lick mode, press and hold the Up and Amp A/B Footswitches simultane-
ously. The Display briefly reads LrnenD.
Note: While the Phrase Looper feature is active, the Learn-A-Lick feature is not available.

Expression Pedal

The Expression Pedal on the RP355 can be linked to control the RP355's Volume, Wah, Wham-
my™, YaYa™, or almost any of the RP355's other parameters in real time with your foot. When
a parameter has been linked to the Expression Pedal, a minimum (heel) and maximum (toe)
value can also be specified. Apply extra pressure to the toe of the Expression Pedal to activate
the V-switch, and the Expression Pedal switches between the linked parameter and the Wah. The
procedure for linking a parameter to the Expression Pedal is as follows:
1. Press either Edit button until the Expression row has been selected (indicated by the LED
lighting on the Expression row).
2. Rotate Knob 1 until eXPPDL appears in the Display.
3. Rotate Knob 2 until the desired parameter to be linked appears in the Display. See page 32
for a complete list of parameters that can be linked to the Expression Pedal.
4. Rotate Knob 3 to select the minimum (heel) value the assigned parameter will reach with the
Expression Pedal in the toe up position.
5. Rotate Knob 4 to select the maximum (toe) value the assigned parameter will reach with the
Expression Pedal in the toe down position.
6. Store your Expression Pedal assignment to your preset. See page 12 for more information on
the storing procedure.

LFOs

The RP355 includes two assignable low frequency oscillators (LFO 1 and LFO 2) which
can be assigned to any of the same parameters available for assignment to the Expression
Pedal. A low frequency oscillator will automatically vary the value of the assigned parameter at
a steady rate. A minimum and maximum value each LFO will reach may be also be assigned.
For instance, if the Amp Gain was assigned to LFO 1, and the minimum value was set at 1 and
the maximum value was set at 99, the RP355 would automatically sweep the amount of
distortion from a clean sound to a distorted sound. Individual LFO speeds are also available
for assignment. In the previous example, the LFO speed would determine the length of time it
took the LFO to sweep from the clean to the distorted sound. The procedure for assigning the
LFOs in the RP355 is as follows:
1. Press the Edit button until the Expression row has been selected (indicated by the LED light-
ing on the Expression row).
2. Rotate Knob 1 to select one of the two LFO links, LFO 1 (LFO1) or LFO 2 (LFO2).
3. Rotate Knob 2 to select the parameter you want linked to the LFO 1 or LFO 2. See page 32
for a list of assignable parameters.
4. Rotate Knob 5 to select which waveform you want the LFO to use, Triangle (trIanG), Sine
(SIne), or Square (SQuAre).
5. Rotate Knob 6 to select the speed you want the parameter to be controlled at.

Factory Reset

This function resets the RP355 to its original factory settings. This procedure erases all custom
User presets, and recalibrates the Expression Pedal.
ATTENTION: Performing this function will erase all user-programmed data. All
such data will be lost forever! Be sure you want to erase the memory and start
fresh before continuing with this procedure.
The procedure for performing a Factory Reset is as follows:
28