Search Method/Code Scan; Special Functions/Ok Key; Easy Set -Up To Operate Your Tuner; Easy Set -Up To Operate Your Tape Recorder - Universal Remote Control TéLéCOMMANDE UNIVERSELLE RC 8 Manual

Easy SET -UP to operate your TUNER

The set-up to operate your TUNER is similar to the set-up procedures for your CD-Player. Follow
the steps 1. until step 10. by using the TUNER/
TUNER replacing the word CD-PLAYER.

Easy SET -UP to operate your TAPE RECORDER

The set-up to operate your TAPE RECORDER is similar to the set-up procedures for your CD-
Player. Follow the steps 1. until step 10. by using the TAPE/
the word TAPE RECORDER replacing the word CD-PLAYER.

Easy programming for the control of your AMPLIFIER

To programme the remote control to operate your AMPLIFIER, proceed as described for the CD
PLAYER. Complete steps 1 to 10 using the AMP/
ply read AMPLIFIER.
Search Method
If the Easy Set-Up procedure was not successfully, try the Automatic Search Method on your RC 8
remote control:
A. Make sure that 2 new batteries have been inserted correctly (see step 1. of the Easy Set-Up).
B. Switch on your TELEVISION.
C. Press the key on your RC 8 (for about 5 seconds) until the LED flashes twice.
TV
D. Enter code
0
E. Press the
15 minutes. (During a code scan for VCR, DVD, CD or TAPE, press and hold the
during a TUNER scan, press and hold key
F. Now press the
TV
G. If your TELEVISION operates incorrectly, repeat step B. to step F.A new code search begins
with the last code number found in the previous search. Please be patient.There may be many
codes to search through before the code for your device is found.
Code scan for VCR, SAT, DVD, CD,TAPE,TUNER and AMP
To complete a code scan for VCR, SAT, DVD, CD,TAPE,TUNER or AMP, proceed as described for
a TV code scan. Complete steps A to G and press keys
/SHIFT + TAPE/
the respective device.
At step E,
for SAT and AMP, press the
for VCR, DVD, CD and TAPE, press the
for TUNER, press key
Special Functions of your RC 8:
Brightness / colour / contrast / etc.
Adjusting brightness / colour / contrast / bass / treble / balance of your television with your RC 8
remote control:
1. Make sure your RC 8 is in the TV-mode (Press
2. Press /SHIFT.
3. Press within 5 seconds:
-
4. Use the and
5. After 5 seconds your RC 8 will return to the normal functions to operate the channel selection.
OK key on your RC 8
• TV-Mode
• TV-Mode/menu
• VCR-Mode
• SAT-Mode
• DVD level
• TAPE-Mode
Make a note of the 3-digits codes of your devices for future reference, because you
will need these codes to set-up your RC 8 remote control again after replacing the
batteries):
TV VCR
with the number keys of your RC 8.The LED flashes twice.
0 1
key on your RC 8 until your TV SET is switched off.This might take up to
key on your RC 8 again until the LED flashes twice.
, /SHIFT + TUNER/
VCR
key;
2
1
3
5
+
to adjust the settings of your television.
Resets your TELEVISION to the basic settings.
Confirmation key.
Recording key (press twice).
Confirmation key.
Confirmation key for settings
Recording key (press twice).
SAT DVD
key on your RC 8 and reading the word
SAT
VCR
DVD key on your RC 8. For CD PLAYER, sim-
).
2
,
VCR SAT
or
SAT
key, and
).
TV
brightness.
contrast.
bass.
CD
key on your RC 8 and reading
, , /SHIFT+ CD/
DVD
/SHIFT + AMP/
colour.
2
treble.
4
balance.
6
TAPE TUNER AMPLIFIER
key;
,
TV
for
DVD