Niles ZR-6 Installation Manual page 37

SYSTEM CONFIGURATION
CONFIGURING THE ZR-6 MULTIZONE RECEIVER
ZONE 5 PRE-OUT
The ZR-6 MultiZone Receiver is equipped with Zone 5 pre-amplifi er
outputs that enable the use of a separate outboard power amplifi er.
While in the confi guration mode (see above), press the Set
button until the display shows [ZONE 5 PRE-OUT VARIABLE].
The default setting is for the preamplifi er outputs to be variable
(controlled by the ZR-6 volume control).
Z O N E 5 P R E O U T
V A R I A B L E
To change these outputs to a fi xed volume level, press the Band
key. The display will show [PRE-OUT 5 FIXED]. The Zone 5 Output
is now set to +6dB relative to the selected source input level .
Z O N E 5 P R E O U T
F I X E D
To continue to the next system confi guration step, Zone 6 Pre-Out,
press the Set button once.
To save the settings and exit the confi guration mode,
simultaneously hold down the Band and Set buttons. After the
ZR-6 saves the information, [RELEASE BUTTONS TO CONTINUE]
appears on the display. The ZR-6 will return to the normal operating
mode.
ZONE 6 PRE-OUT
The ZR-6 MultiZone Receiver is equipped with Zone 6 pre-amplifi er
outputs that enable the use of a separate outboard power amplifi er.
While in the confi guration mode (see above), press the Set button
until the display shows [ZONE 6 PRE-OUT VARIABLE]. The default
setting is for the preamplifi er outputs to be variable (controlled by
the ZR-6 volume control).
Z O N E 6 P R E O U T
V A R I A B L E
To change these outputs to a fi xed volume level, press the Band
button. The display will show [PRE-OUT 6 FIXED]. The Zone 6
Output is now set to +6dB relative to the selected source input level.
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373
Z O N E 6 P R E O U T
F I X E D
To continue to NAMING THE SOURCE DEVICES, press the Set
button once.
To save the settings and exit the confi guration mode, simultaneously
hold down the Band and Set buttons. After the ZR-6 saves the
information, [RELEASE BUTTONS TO CONTINUE] appears on the
display. The ZR-6 will return to the normal operating mode.
NAMING THE SOURCE DEVICES
While in the confi guration mode, press the Set button until the
display shows [SOURC NAME]. Press the Band button to highlight
a source number. The numbers indicate the six sources of the ZR-6
MultiZone Receiver. The cursor will return to Source 2 after Source
6. You cannot re-name Source 1 because it is always the built-in
AM/FM tuner. The default name for Source 2 is iPod.
3 4 5 6
I P O D
If an iPod will not be used with the system, select a name for
the source device 2. If iPod remains as the Source 2 name
and no iPod is connected, whenever Source 2 is chosen [IPOD
DISCONNECTED] will appear on the screen.
Press the Band button to highlight the source number. The cursor
moves to the next source as you press the Band button, returning
to Source 2 after Source 6. With a source number highlighted,
toggle through the available source device names by pressing
the + and – buttons.
2 4 5 6
S A T R A D I O
The source device name that is selected is the name that will
appear on the LCD displays of Solo-6 MD Master Keypads
whenever that source is selected. There are 35 source device
names available. They appear in alphabetical order, except N/A
which appears fi rst, and iPod which appears fi rst for Source 2 only.
S O U R C N A M E
S O U R C N A M E
(CONTINUED ON NEXT PAGE)
35