Related Manuals for NETGEAR GSM7228PS-100NAS
Summary of Contents for NETGEAR GSM7228PS-100NAS
- Page 1 Managed Stackable Switches GSM7200PS and GSM7300S Series Ha r dw a r e I n s ta ll ati on Gu ide 350 East Plumeria Drive San Jose, CA 95134 March 2010 202-10532-02 v1.0...
-
Page 2: Technical Support
To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. -
Page 3: Table Of Contents
Table of Contents Chapter 1 Introduction GSM7228PS Front Panel and LEDs ......5 GSM7228PS Rear Panel . - Page 4 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Specifications for GSM7328S and GSM7352S .....33 Appendix B Default Configuration Settings Appendix C Notification of Compliance Table of Contents...
-
Page 5: Chapter 1 Introduction
The NETGEAR Managed Stackable Gigabit Ethernet Switch is a state-of-the-art, high-performance, IEEE-compliant network solution. It includes powerful management features that you can use to eliminate bottlenecks, boost performance, and increase productivity. This guide describes hardware installation and basic troubleshooting for the following NETGEAR switches: •... - Page 6 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table 1-1. LED Descriptions for GSM7228PS Description This is the stack member ID (1–8) that the software assigns to the switch. • Power Solid green: The power module is present, is supplying power to the switch, and is working normally.
- Page 7 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table 1-1. LED Descriptions for GSM7228PS (Continued) Description SPD/Link/ACT LED: 10/100/1000M Ports (2 LEDs per port) • Off: No link is established on the port. • Solid green: A valid 1000 Mbps link is established on the port. •...
-
Page 8: Gsm7228Ps Rear Panel
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide GSM7228PS Rear Panel The rear panel has two module bays, a console port, redundant power supply connector, and a power module bay for the APS525W. Power supply connector AC Power Console Stacking/XFP/SFP+/CX4 Connector... - Page 9 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table 1-3. GSM7252PS LED Description Description This is the stack member ID (1–8) that the software assigns to the switch. Power • Solid green: The power module is present, is supplying power to the switch, and is operating normally.
-
Page 10: Gsm7252Ps Rear Panel
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table 1-3. GSM7252PS LED Description (Continued) Description • ports Off: No SFP module link is established on the port. • Solid green: A valid 1000 Mbps SFP module link is established on the port. •... -
Page 11: Gsm7328S Front Panel And Leds
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide GSM7328S Front Panel and LEDs The following figure shows the front panel of the GSM7328S. The front panel contains LEDs, a Reset button, a USB port, RJ-45 jacks, copper/fiber combo ports, and 10G SFP+ ports. Combo Ports RJ-45 jacks LEDs... -
Page 12: Gsm7328S Rear Panel
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table 1-5. LED Descriptions for GSM7328S (Continued) Description 10/100/1000M Ports Link/ACT LED: (2 LEDs per port) • Off: No link is established on the port. • Solid green: A valid link is established on the port. •... -
Page 13: Gsm7352S Front Panel And Leds
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide • SFP+ Adapter AX743 • CX4 Adapter AX744 • ProSafe 24-Gigabit Stackable Module AX742. For more information, see “Adapters and Modules Compatible with the High-Speed I/O Module Bays” on page 2-21. GSM7352S Front Panel and LEDs The following figure shows the front panel of the GSM7352S. -
Page 14: Gsm7352S Rear Panel
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table 1-6. GSM7352S LED Description (Continued) LEDs Description 10/100/1000M Ports Link/ACT LED: (2 LEDs per port) • Off: No link is established on the port. • Solid green: A valid link is established on the port. •... -
Page 15: Safety Instructions
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide The module bays support any combination of the following: • ProSafe 10-Gigabit Ethernet XFP Adapter (AX741) • SFP+ Adapter AX743 • CX4 Adapter AX744 • ProSafe 24-Gigabit Stackable Module AX742. For more information, see “Adapters and Modules Compatible with the High-Speed I/O Module Bays”... - Page 16 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide • To help avoid damaging your system, be sure that the voltage selection switch (if provided) on the power supply is set to match the power available at your location: 115 volts (V), 60 hertz (Hz) in most of North and South America and some Far Eastern countries such as South Korea and Taiwan 100 V, 50 Hz in eastern Japan and 100 V, 60 Hz in western Japan...
-
Page 17: Chapter 2 Hardware Installation
Resource CD: The CD either includes these documents or links to access them: ProSafe 7200PS Managed Switch CLI Manual, Version 8.0.2 NETGEAR 7000 Series Managed Switch Administration Guide NETGEAR Installation Guide for the 7000 Series Stackable Managed Switch This Hardware Installation Guide •... -
Page 18: Protecting Against Electrostatic Discharge
2-17. Note: If any item is found missing or damaged, contact your local NETGEAR reseller for replacement. Inspect the products and accessories for damage. Report any damage immediately. Installation Install the equipment in the sequence presented in this section:... -
Page 19: Select A Location
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Select a Location. See “Select a Location” on page 2-19. Install the Switch. See “Install the Switch” on page 2-20. Check the installation. See “Check the Installation” on page 2-20. Apply power and check the LEDs. -
Page 20: Install The Switch
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Install the Switch You can install the switch on a flat surface or in a standard 19-inch rack. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bottom of the switch. -
Page 21: Connect To Power And Check The Leds
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Verify that all cables are installed correctly. Check cable routing to ensure that cables are not damaged and will not create a safety hazard. Be sure that all equipment is mounted properly and securely. Connect to Power and Check the LEDs The switch does not have an On/Off switch. - Page 22 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide • ProSafe 24-Gigabit stacking module AX742 Figure 2-11 AX742 • ProSafe 10-Gigabit Ethernet SFP+ Adapter Module AX743: Figure 2-12 AX743 • ProSafe 10-Gigabit Ethernet CX4 Adapter AX744: Figure 2-13 AX744 After the appropriate adapter has been installed, the following modules (sold separately) can be inserted into the adapter’s module bay: •...
-
Page 23: Installing An Adapter And Module
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide • SFP module with LC connector, compatible with the IEEE 802.3z 1000Base-X standard. Figure 2-14 SFP Module Installing an Adapter and Module The steps are the same for adapter models AX741, AX742, AX743, and AX744. First, install the adapter into the switch: Figure 2-15 Adapter Installation... -
Page 24: Creating A Stack
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Creating a Stack You can connect up to eight switches to form a stack with a single management IP address. The switches automatically select a master unit. Once the master is selected, you can use its console to manage all the switches in the stack. -
Page 25: Power Module Bay
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Power Module Bay The power module bay provides an easy way to replace a failed power module APS525W or APS135W. If the switch needs to continue to operate while you replace the power supply, an appropriate Redundant Power Supply (RPS) must be used to connect to the redundant power supply connector on the switch rear panel. -
Page 26: Connecting A Redundant Power Supply
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Connecting a Redundant Power Supply Each switch has a redundant power supply (RPS) connector at the rear of the switch next to the power supply panel. Power receptacle Redundant power supply connector Figure 2-19 Redundant Power Supply You can connect an external DC-to-DC power supply unit to the switch to provide redundant... - Page 27 PDF format on the Resource CD). • ProSafe 7200PS Managed Switch CLI Manual, Version 8.0.2: Gives detailed examples of how to use the CLI. • NETGEAR 7000 Series Managed Switch Administration Guide: Describes configuration tasks. Chapter 2: Hardware Installation | 27...
-
Page 28: Chapter 3 Troubleshooting
Troubleshooting Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Table 3-1. Troubleshooting Chart Problem Cause Solution Power LED is off. No power is received Check the power cord connections for the switch at the switch and the connected device. Make sure that all cables used are correct and comply with Ethernet specifications. -
Page 29: Additional Troubleshooting Suggestions
You can verify the integrity of the switch by resetting the switch. To reset the switch, use the Tools> Reset command or remove AC power from the switch and then reapply AC power. If the problem continues, contact NETGEAR technical support. Auto-Negotiation: The copper 10/100/1000 Mbps ports negotiate the correct duplex mode and speed if the device at the other end of the link supports auto-negotiation. -
Page 30: Appendix A Technical Specifications
Technical Specifications Specifications for GSM7228PS and GSM7252PS Table A-1. Technical Specifications for GSM7228PS and GSM7252PS Feature GSM7228PS GSM7252PS IEEE Network Protocol • 802.3 10BASE-T • and Standards 802.3u 100BASE-TX • compatibility 802.3z 1000BASE-SX • 802.3z 1000BASE-LX • 802.3ab 1000BASE-T • 802.3ae 10000BASE-LR •... -
Page 31: Specifications For Gsm7228Ps And Gsm7252Ps
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table A-1. Technical Specifications for GSM7228PS and GSM7252PS (Continued) Feature GSM7228PS GSM7252PS • Layer 2 services 802.1Q Static VLAN (Up to 4k) • 802.1p Class of Service (CoS) • 802.1D Spanning Tree Protocol (STP) •... -
Page 32: Specifications For Gsm7328S And Gsm7352S
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table A-1. Technical Specifications for GSM7228PS and GSM7252PS (Continued) Feature GSM7228PS GSM7252PS Power consumption 545 W maximum 100–240VAC, 50–60 570 W maximum 100–240VAC, 50–60 Hz universal input when PoE output Hz universal input when PoE output 384W 384W... -
Page 33: Specifications For Gsm7328S And Gsm7352S
Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table A-2. Specifications for GSM7328S and GSM7352S (Continued) Feature GSM7328S GSM7352S • Switch management Port mirroring support • SNMP v1, v2c, v3 • RFC1757 RMON 1 groups 1, 2, 3, and 9 •... - Page 34 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Table A-2. Specifications for GSM7328S and GSM7352S (Continued) Feature GSM7328S GSM7352S • Interface (Auto Uplink on 48 RJ-45 connectors for • all RJ-45 ports) 24 RJ-45 connectors for 10BASE-T, 10BASE-T, 100BASE-TX, and 100BASE-TX, and 1000BASE-T 1000BASE-T •...
-
Page 35: Default Configuration Settings
Default Configuration Settings Feature Default Setting Port speed Auto-negotiation Port duplex Auto-negotiation Flow control (half duplex) Enabled Flow control (full duplex) Disabled Broadcast storm control Enabled Gigabit port type Auto detect Management IP DHCP configuration Password protection Disabled User name Admin Password (none) - Page 36 Managed Stackable Switches GSM7200PS and GSM7300S Series Hardware Installation Guide Feature Default Setting GVRP Disabled GMRP Disabled IP routing Disabled Enabled MAC address aging 300 seconds OSPF Disabled SNMP community public (read-only access), private (read/write access) DHCP Server Disabled VLAN Ingress filtering Enabled IP multicast filtering Disabled...
- Page 37 Please refer to the notes in the operating instructions. It is hereby certified that the NETGEAR ProSafe 24-port Gigabit L3 Managed Stackable Switch GSM7328S has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992.The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions.
-
Page 38: Canadian Department Of Communications Radio Interference Regulations
Communications du Canada. EN 55 022 Declaration of Conformance This is to certify that the NETGEAR ProSafe 24-port Gigabit L2+ Managed Stackable Switch with PoE GSM7228PS is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. - Page 39 EN 55 022 and EN 55 024 Statements This is to certify that the NETGEAR ProSafe 24-port Gigabit L2+ Managed Stackable Switch with PoE GSM7228PS is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.