Casio XW-P1 User Manual page 67

Display
Arp Enable
Phrase Enable
Controller >Ent
K1
K2 to K4
Pedal
Touch
TchOffVel
Sequencers >Ent
Tempo
Step SEQ Number Step sequencer number. Specifies the Step Sequencer sequence (page E-51).
Solo1 Ch
Change
Key Shift
Pattern
Arp On/Off
Arp Type
ArpKeyRgLo
Arpeggio on/off. Enables/disables arpeggio function (page E-40) for each zone.
Phrase on/off. Enables/disables the Phrase Sequencer (page E-44) for each zone.
Controller parameters. This is group of editable controller parameters.
Knob Target 1. Selects the parameter controlled by
"CC67:Soft" is specified for this setting,
CC00 to CC97: MIDI control change*
NRPN, RPN: MIDI NRPN and RPN parameters*
Ch Pressure: MIDI channel pressure*
Arpeggio: Preset arpeggio type (page E-40)
Tempo: Tempo setting (page E-45)
EQ Low Gain - EQ High Gain: Master EQ >Low Gain - High Gain (page E-38)
*1 For details about each setting, refer to the MIDI Implementation document
(http://world.casio.com/) and other MIDI documentation.
*2 After selecting these parameters, press
MSB: 63H for NRPN, 65H for RPN (Setting range: 000 to 127)
LSB: 62H for NRPN, 64H for RPN (Setting range: 000 to 127)
Send Data: Specifies whether knob operation controls MSB or LSB. (Settings: MSB, LSB)
Knob Target 2 to Knob Target 4. As with K1 (Knob Target 1), Selects the parameter controlled by
3
K2 to K4 knob operation.
Pedal. Specifies the function of the pedal plugged in to
Hold: Pressing the pedal sustains notes. This is a sustain effect.
Soft: Pressing the pedal slightly lowers the volume of notes.
Sostenuto (Sostenut): Pressing the pedal while keyboard keys are depressed sustains (holds)
only the notes of the pressed keyboard keys.
Step Sequencer Play/Stop (SSEQ P/S): Pressing the pedal starts or stops Step Sequencer
sequence playback.
Phrase Sequencer Play/Stop (Phrase P/S): Pressing the pedal starts or stops Phrase Sequencer
phrase playback.
Phrase Record (Phrase REC): Same function as the Phrase Sequencer
Rotary Slow/Fast (Rotary S/F): Pressing the pedal performs the same operation as drawbar
2
organ tone SLOW/FAST. This changes the speed of rotary speaker rotation.
Touch. Specifies touch sensitivity when the keyboard is played.
Off (Off): Notes sound at a fixed volume level regardless of keyboard pressure.
Normal
Light: High-volume notes are easily produced even with light keyboard pressure.
Touch off velocity. Specifies the volume level at which the above touch curve setting values
become off.
Sequencers parameter. This group includes Step Sequencer (page E-49), Phrase Sequencer
(page E-44), and Arpeggio function (page E-40).
Tempo. Adjusts the Phrase Sequencer and Step Sequencer playback tempo. You also can
change the playback tempo using
Step Sequencer solo track part. Step Sequencer Solo Track 1 is normally Part 14, but it can be
changed to Part 1 (Zone Part 1, page E-54).
Step Sequencer change timing. Specifies the switching timing when a pattern is changed by the
Step Sequencer (page E-55).
Step Sequencer key shift Switches the Step Sequencer key shift function between on and off
(page E-51).
Step sequencer pattern number. Selects the step sequencer pattern (page E-49).
Arpeggio on/off. The arpeggio function is disabled while this setting is off.
Arpeggio type. Specifies the arpeggio type (page E-40).
Arpeggio key range low. Specifies the low keyboard range where the arpeggio function is
enabled. This setting is used in combination with the Arpeggio Key Range Hi setting to configure
the keyboard range where the arpeggio function is enabled.
Description
3
K1 knob operation. For example, if
3
K1 operation will apply a soft pedal effect.
1
*
1 2
1
bq
ENTER again and then adjust the items below.
ck
SUSTAIN/ASSIGNABLE JACK.
8
TEMPO.
Using the Performance Mode
Off, On
Off, On
Refer to the cell to
the left.
Same as K1.
Refer to the cell to
the left.
bn
REC button.
Refer to the cell to
the left.
0 to 127
30 to 255
Preset00 to
User99
1, 14
Wait, Real
Off, On
1 to 8
Off, On
Preset00 to
User99
C-1 to G9
Settings
E-65