Editable Performance Parameter List - Casio XW-P1 User Manual

Using the Performance Mode

Editable Performance Parameter List

Editable Parameter List
Display
Zone Parame >Ent
Zone
Tone
KeyRangLow
KeyRangHi
Volume
Pan
Oct.Shift
Transpose
FineTune
BendRngDwn
BendRngUp
Rev Send
Cho Send
DSP Line
Knob1Enable
Knob2Enable
Knob3Enable
Knob4Enable
Bend Enable
Wheel Enable
Pedal Enable
E-64
Zone parameters. This group includes parameters for each of the zones (Zone 1 through 4).
9
• Use the PART minus (–), plus (+) buttons to select the zone you want to edit.
• You also can enter the group using the following shortcut: Perform step 2 under "To register a
performance" (page E-62) and then hold down
Zone on/off. Turns all zones on or off This setting is different from the mixer function page (page
E-68) part on/off (Part Enable) setting.
Tone. Selects the tone for each zone. This setting is the same as the mixer function part tone
(page E-68).
• While this item is selected, you can select a tone using the same operation as that used in the
Tone Mode.
• This setting can also be configured using quick editing (page E-16).
• There are some limitations on the selection of tone categories for Zones 2 through 4 (page
E-16).
• A tone with DSP will have DSP next to the tone name on the display (page E-37).
Key range low. Specifies the low key range of the keyboard for each zone. This setting is used in
combination with the Key Range Hi setting to configure key ranges for each zone.
For example, configuring F3 (low) to C7 (high) for Zones 1 and 2 and C2 (low) to E3 (high) for
Zones 3 and 4 will enable play of Zone 1 and 2 tones on the right side keyboard range in the
illustration below, and the Zone 3 and 4 tones on the left side keyboard.
Zone 3
Zone 4
C2 E3 F3
• Setting can be specified using the keyboard keys.
Key range high. Specifies the high range of the keyboard for each zone. This setting is used in
combination with the Key Range Lo setting to configure key ranges for each zone.
Volume. This setting is the same as the mixer function tone volume (page E-68).
Pan. Adjusts the left-right position of sound in the stereo field. This setting is the same as the
mixer function part panning (page E-68).
Octave shift. Shifts the tone of notes by octave units.
Transpose. Shifts the tone of notes by semitone units. This setting is the same as the mixer
function part coarse tune (page E-68).
Fine tune. This setting is the same as the mixer function part fine tune (page E-68).
Bend range down. Pitch change amount for downward bender operation.
Bend range up. Pitch change amount for upward bender operation.
Reverb send. This setting is the same as the mixer reverb send (page E-68).
Chorus send. This setting is the same as the mixer chorus send (page E-68).
DSP line. This setting is the same as the mixer function part DSP line (page E-68).
Knob 1 on/off. Enables/disables
Knob 2 on/off. Enables/disables
Knob 3 on/off. Enables/disables
Knob 4 on/off. Enables/disables
Bender on/off. Enables/disables
Modulation wheel on/off. Enables/disables
Pedal on/off. Enables/disables operation of a pedal plugged in to the
ASSIGNABLE JACK for each Zone.
Description
7
EDIT. This will enter the group.
Zone 1
Zone 2
3
K1 operation for each zone.
3
K2 operation for each zone.
3
K3 operation for each zone.
3
K4 operation for each zone.
bs
BENDER operation for each zone.
bs
MODULATION operation for each zone.
C7
ck
SUSTAIN/
Settings
Off, On
Zone 1:
Solo Synth P00 to
Various U29
Zone 2 to 4:
Piano P00 to
Various U29
C-1 to G9
C-1 to G9
0 to 127
–64 to 0 to +63
–2 to 0 to +2
–12 to 0 to +12
–99 to 0 to +99
0 to 24
0 to 24
0 to 127
0 to 127
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On