Table of Contents
Advertisement
How-tos
How-tos
This section contains detailed guides on how to quickly
set-up your instrument to match various conditions.
CONNECTING A BASS PEDAL UNIT
Connect a MIDI cable between MIDI OUT of your bass ped-
BASS PEDAL
al unit and
input.
• All MIDI messages will be received via the
input regardless of MIDI channel setting.
• MIDI messages received via the
BASS MIDI CHANNEL
on the
• MIDI messages will be received on the
NEL
MIDI IN
via
.
• Local Control settings apply to devices connected via
BASS PEDAL
the
input.
SETTING UP THE HALF MOON SWITCH
The Half Moon Switch is an accessory item and sold sepa-
rately. When set to Half Moon Switch operation, the
RY SPEAKER
buttons on the front panel, as well as Rotary
Speed Continuous Controller messages received via
IN
are disabled.
1
Mount the Half Moon Switch following the
included instructions.
2
Connect the Half Moon Switch to the
CONTROL
input
3
Press
SHIFT
+
SYSTEM
to enter the System Menu
4
Navigate with the PAGE/MENU buttons to
page 7
5
Change setting
SHIFT
PAGE/MENU
Press
+
to "HA"
6
Press SYSTEM / MIDI / SOUND buttons to exit
menu
ADJUSTING THE PEDAL POLARITY
If you encounter the sustain or rotary control pedal operat-
ing "backwards" you can adjust the pedal polarity in the
System Menu.
1
Press
SHIFT
+
SYSTEM
to enter the System Menu
2
Navigate with the PAGE/MENU buttons
For adjusting the sustain pedal, navigate to page 5.
For adjusting the rotary pedal, navigate to page 7.
3
Change setting
Press
SHIFT
+
PAGE/MENU
4
Press SYSTEM / MIDI / SOUND buttons to exit
menu
18
BASS PEDAL
BASS PEDAL
input is sent
MIDI OUT
via
.
BASS MIDI CHAN-
ROTA-
MIDI
ROTARY
buttons and change setting
buttons to change setting.
User Manual
ADJUSTING THE SWELL PEDAL SPAN
As expression pedals from different manufacturers have
various span characteristics, you can select span preset in
the System Menu.
1
Press
SHIFT
+
2
Navigate with the PAGE/MENU buttons to
page 9
3
Change setting
SHIFT
PAGE/MENU
Press
+
FA
Fatar
ER
Ernie Ball
YA
Yamaha
RO
Roland
If the manufacturer of your pedal is not listed above,
you can try operating the pedal to it's end positions.
The pedal range is briefly shown in the
value between 0 and 100. Select the setting that best
match the range of your pedal.
PLAYING AN EXTERNAL SOUND
SOURCE
Since both manuals send MIDI data on separate MIDI chan-
nels, it is possible to connect an external sound source and
control it from one manual while playing internally on the
other.
Follow the steps below as necessary:
1
Connect
MIDI OUT
device
2
Match MIDI channels
Match the MIDI channel setting of the manual you
want to use with your external device. Please refer to
"The MIDI Menu" on page 15 for detailed instructions.
• MIDI channel setting 1 - 16 uses the fast trigger key-
board response which result in MIDI note messages
being sent with fixed velocity data.
• MIDI channel setting E1 - E9 uses normal trigger
response which result in velocity variable data being
MIDI OUT
sent via
internally.
3
Set MIDI CC Mode to "Off"
Normally all buttons and knobs send MIDI continuous
controller data, which can lead to undesirable results
when an external sound generator is connected.
This can be turned of by setting the MIDI CC Mode to
"Off" or "Receive". This is done in the MIDI menu. Please
see "Continuous Controller mode" on page 16 for
detailed instructions.
4
Set Sustain Pedal Mode
If you want the sustain pedal to operate the external
device only, set the sustain pedal setting in the System
menu to "
OF
". Please refer to "Sustain Pedal" on page 15
for detailed instructions.
SYSTEM
to enter the System Menu
buttons to change setting.
DISPLAY
to MIDI in on the external
. Fast trigger response is still used
as a
Advertisement
Table of Contents
