Communication — — — — Key Press — — — — Trigger — Communication — — while Sampling Warm up is not supported during long-period sampling. SONIC sampling triggered by CH1, CH2, or CH3 is not supported. – 2 –...
120000 ([Number of Variable using power supply command (Command 10). Channels Used] + 1) 17140 Sampling Interval * The number of samples is 2^n when FFT Samples (n) is used. 100msec 5pin Power supplied during ready state. – 3 –...
Auto-ID +5.3V DC +5.3V DC • List (N line data) {CH1 data n, CH2 data n, CH3 data n, SONIC data n, DIG IN data n, sampling Vin-low 0–5V Not used time n} (n: number of samples at the point that request is made) 2.
Page 6
Command 3 - Sample and Trigger Setup { 3, Sampling Interval, Number of Samples, Record Time, Trigger Source, Trigger Threshold, Trigger Edge, Clock Source } Sampling Interval Number of Samples Record Time 0.00002 Number of seconds 1 to Number of samples...
Page 7
Input 0 for constants that are not used. • When the conversion result of the “conversion equation” selected by Command 4 causes an overflow, the EA-200 sends a result of zero (0) to the calculator. Command 5 - Data Range Setup...
Page 8
• An error occurs when fraction data is sent. • Send commands to the EA-200 in accordance with the command table contents. • An error occurs when a parameter that does not exist in the command table is sent. • The EA-200 uses six digits for internal calculations.
Clear Command 1 data of specified channel. Auto-ID Digital Out Perform sampling using automatically recognized sensor. (Channel = 6) Perform 0 to 5V sampling when recognition is not possible. Clear Dig O channel information. Voltage sampling 1 to 32 Number of loops Resistance sampling 1–100kΩ...
Page 10
Output Example <Output Trigger> When the list is: 85(1010101), 34( 100010), 187(10111011), 204(11001100) Following receipt of Command 3, output starts as soon as a Trigger Source is generated. Clock The following can be specified as a Trigger Source. 0: None, 1: [Start] key, 10: Countdown, Command 8 Output is interrupted when the Start/Stop key is pressed.
Page 11
In addition, quadratic data is sent when data is requested. • When 10 and 11 (FFT) After sampled data is sent, FFT real number part data is sent when data is requested. In addition, FFT imaginary number part data is sent when data is requested.
20 Countdown When [Start/Stop] key is pressed or when Command 8 is received, { 3, Sampling Interval, Number of Samples, Record Time, Trigger Source, Trigger countdown is performed by beeping at 1-second intervals the number of Threshold, Trigger Edge, Clock Source } times specified by count number, and then sampling starts.
Page 13
3 Difference Rising value is greater than hysteresis lower limit. Sampling started when [Current Value] – [Previous Value] > [Trigger To trigger at a target threshold, increase or decrease the hysteresis part with Threshold] the edge settings to specify the threshold.
Polynomial: Input constants in sequence from Kn = 0 X > 0 9 Geometric Mixed polynomial: Input constants in sequence from m= 4 to 1, n = 0 to 5. 10 Modified geometric X > 0 11 Reciprocal logarithmic [K In(K –1...
Command 5: Data Range Settings 1– Number of steps (Specifying 2 sends ever other data item). { 5, Channel Select, Data Select, Data Begin, Data End, Step, K (, FFT Samples) } –1 Send using step equivalent to [Number of Sampled Data] [Specified Value K] Cannot be used during sampling.
Command 7: Status Check { 7 } After Command 7 is received, this function sends EA-200 status information upon a data request from the calculator. Status Request Line Line Line Basic Information Status 0: Standby 31 Channel 2 Setup Post-Processing...
If a sampling Trigger Source is generated before supply time is reached, supply (4) Baud rate : 38400 bps. time takes priority and sampling starts after it is reached. When parameter is –1, (5) Parity bit : none. however, sampling starts as soon as sampling Trigger Source is generated.
Page 18
Check Type: A (Ascii) Type Form Line Offset Packet size 0×FF Area Check Type (Char, 1byte) : ASCII Number 1 , ASCII Number 2 , … ASCII Number N ASCII Form (Char, 1byte) Variable List Line (Hex, 2byte Big endian) 0×0001~...
Page 19
1 Except the star code, add the data code to send (hexadecimal number) one by one byte. 2 As a result, one byte of the code that excludes the overflowed digit is set to “SUM”. 3 Calculate the complementary number for 2 of SUM’. The answer is used as the checksum code.
Page 20
CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan SA0601-A –2–...