Display Section; Operations - Pioneer DJM-800 Operating Instructions Manual

NAMES AND FUNCTIONS OF PARTS (DISPLAY SECTION)
DISPLAY
SECTION
1. Effects display section
The <EFFECT SELECT> indicator lights constantly, and the
alpha-numeric display (seven characters in two lines) indicates
the name of the effect as shown below. Also, when one of the
change operations is performed as noted in the table, the
corresponding characters are displayed for two seconds, after
which the display returns to the original effect name.
Switching Operation
At MIDI start
At MIDI stop
MIDI snapshot
1 Effect display
Effect
Upper/
selector
Lower
DELAY Upper DELAY
Lower
ECHO Upper ECHO
Lower
REV DLY Upper REVERSE
Lower DELAY
PAN Upper PAN
Lower
TRANS Upper TRANS
Lower
FILTER Upper FILTER
Lower
FLANGER Upper FLANGER
Lower
PHASER Upper PHASER
Lower
REVERB Upper REVERB
Lower
ROBOT Upper ROBOT
Lower
CHORUS Upper CHORUS
Lower
ROLL Upper ROLL
Lower
REV ROLL Upper REVERSE
Lower ROLL
SND/RTN Upper SEND/
Lower RETURN
12
EFFECT SELECT
CH SELECT
1 2 3 4
A B
MIC MST
PARAMETER
MIDI
AUTO
TAP BPM
%
Upper/
Display
Lower Row
Upper MIDI
Lower START
Upper MIDI
Lower STOP
Upper SNAP
Lower SHOT
3 Parameter display
Minimum Maximum
Effect name
value value
1 4 000
1 4 000
10 4 000
10 16 000
10 16 000
10 32 000
10 32 000
10 32 000
1
–100
10 32 000
10 4 000
10 4 000
2. Channel select display section
The <CH SELECT> indicator lights constantly, and a red frame
lights around the number position corresponding to the
1 chosen effect channel selector.
3. Parameter display section
<PARAMETER>:
The <PARAMETER> indicator lights constantly.
AUTO/TAP:
2
[AUTO] lights when the BPM measuring mode is set to AUTO,
and [TAP] lights when the BPM measuring mode is set to
manual (TAP).
BPM counter display (3 digits):
In AUTO mode, displays the automatically detected BPM value.
3
If the BPM count cannot be detected automatically, the display
will flash at the previously detected value. In manual (TAP)
mode, displays the BPM value designated by TAP input, etc.
BPM:
4
Lights constantly.
MIDI:
Displays the MIDI start/stop status.
¶ Indicator lights after MIDI start command has been sent.
¶ Indicator goes out after MIDI stop command has been sent.
Parameter 1 display (5 digits):
Displays parameters designated for each effect. When the beat
select buttons (BEAT 2, 3) are pressed, the corresponding
beat multiple change is displayed for one second. If the beat
select buttons (BEAT 2, 3) are used to designate a value
outside the parameter range, the current number will flash
but will not change.
Unit Display (%/ms):
Lights in accordance with the unit used for each effect.
4. Beat display section
Displays the location of parameter 1 relative to BPM (1/1 beat).
The lower row is lighted constantly. When the parameter 1
location approaches a threshold value, the corresponding
indicator is lighted. When the parameter 1 is between
threshold values, the indicator flashes. Although the display
includes seven actual indicators, the two ends can also be
considered to act as indicators, with the result that a
theoretical nine positions can be postulated. When the values
are at the two ends, no indicators light.
Default Unit
500 ms
500 ms
500 ms
500 ms
500 ms
2 000 ms
2 000 ms
2 000 ms
100 50 %
100 0 %
2 000 ms
500 ms
500 ms
4 Beat display
1 2 3 4 5
1/8 1/4 1/2 3/4 1/1
1/8 1/4 1/2 3/4 1/1
1/8 1/4 1/2 3/4 1/1
1/16 1/8 1/4 1/2 1/1
1/16 1/8 1/4 1/2 1/1
1/4 1/2 1/1 2/1 4/1
1/4 1/2 1/1 2/1 4/1
1/4 1/2 1/1 2/1 4/1
10 20 30 40 50
— –100 –66 –50 0
1/4 1/2 1/1 2/1 4/1
1/16 1/8 1/4 1/2 1/1
1/16 1/8 1/4 1/2 1/1
Shaded items
6 7 8 9
2/1 4/1 8/1 16/1
2/1 4/1 8/1 16/1
2/1 4/1 8/1 16/1
2/1 4/1 8/1 16/1
2/1 4/1 8/1 16/1
8/1 16/1 32/1 64/1
8/1 16/1 32/1 64/1
8/1 16/1 32/1 64/1
60 70 80 90
26 50 100 —
8/1 16/1 32/1 64/1
2/1 4/1 8/1 16/1
2/1 4/1 8/1 16/1
are not displayed.